AUO DISPLAY PLUS PN10ETA02.0 Panel PC User Guide
- June 4, 2024
- AUO DISPLAY PLUS
Table of Contents
Quick Start Guide
This quick guide will help you go:through installation quickly
PN1OETA02.0
Panel PC
https://www.qbictechnology.com/td-1060slim
Contents
Indication
1. DC 12V
2. Micro SDHC
3. USB 2.0
4. RJ45 / PoE+
5. USB 2.0
6. Micro USB for ADB| 7. Audio Jack
8. Front LED
9. Display
10. Factory Reset button
11. Power button
12. Kensington Lock Slot
---|---
Installation
1. Cable connection
STEP 1
The connection cable Device will power on when DC/PoE+ is insert| STEP 2
Install I/O cover| STEP 3
Fix 2*M2 screws
---|---|---
2. Tape Mount
STEP 1 Attach tape on the back of bracket| STEP 2 Place the bracket on the
back side of Panel PC| STEP 3 Fasten M3 screw*1 to secure the bracket and back
cover| STEP 4 Fix the Panel PC on the surface via using tape
---|---|---|---
3. Surface Mount
STEP 1 Install bracket on surface (screws not included)| STEP 2 Mount the
Panel PC on the bracket| STEP 3 Fasten M3 screw*1 to secure the bracket and
back cover
---|---|---
NOTICE:
This Panel PC is also compatible with VESA mounting 75mm x 75mm. It is
recommended to use M3 screws to lock. The suggested length of the M3 screw is
the thickness of the VESA mounting bracket plus 8mm(Screw not included).
Please ensure the mounting surface is clean and smooth before using the tape.
M2 / M3 screw Torque<2 kgf-cm
Installation height: <2 m
CARE AND WARNING
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/panel PC technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- May not cause harmful interference.
- Must accept any interference received, including interference that may cause undesired operation.
Correct Disposal of this product. This marking indicates that this product
should not be disposed of with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling. The power
consumption of the product in networked standby is 5.7W which all wired
network ports are connected and all wireless network ports are a tivated. FCC
& CE RF Radiation Exposure Statement Caution: To maintain compliance with the
FCC & CE’s RF exposure guidelines, place the product at least 20cm from nearby
persons. – Replacement of a battery with an incorrect type that can defeat a
safeguard (for example, in the case of some lithium battery types);
– Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion;
– Leaving a battery in an extremely high-temperature environment can result in
an explosion or the leakage of flammable liquid or gas:
– A battery subjected to extremely low air pressure may result in an explosion
or the leakage of flammable liquid or gas
CAUTION Risk of explosion if the battery is replaced by an incorrect type. Wait one-half hour after switching off before handling parts
Removal
STEP 1 Remove the top screw connecting the TD-1060 slim to the bracket| STEP 2
With both hands supporting the top and bottom of the TD-1060 slim, carefully
tilt the top section of the device downward 30°| STEP 3 Gently pull the
TD-1060 slim down to remove from bracket
---|---|---
STEP 4 Apply hot air gun to the tape beneath bracket until loose| STEP 5
Slowly pull the tape and the bracket downward off the surface
---|---
NOTE:
DO NOT remove bracket or tape from the surface forcefully. Excessive force
during removal may lead to a damaged surface.
Variable Installation
Discrtee Cable Outlets
The TD-1060 Slim is designed for landscape or portrait installation with a
discreet. cable management system.
Surface Preparation for Applying Adhesive Tape
Most substrates are best prepared by cleaning with a 50:50 mixture of
isopropyl alcohol (IPA) and water* prior to applying Tapes. There are
exceptions!
Exceptions to this general procedure that may require additional surface
preparation include:
- Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a surface and should be followed by cleaning with IPA/water.
- Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or oxidation and can increase surface area to improve adhesion.
- Porous Surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc. need to be sealed to provide a unified surface.
- Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper and copper containing metals and plastics or rubber that contain components that migrate(e.g. plasticizers).
General Procedure
- To obtain optimum adhesion, the bonding surfaces must be well unified, clean, and dry. Typical surface cleaning solvents are IPA/ water mixture (rubbing alcohol) or heptane.* (Steps A and B)
- Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure develops better adhesive contact and helps improve bond strength. (steps C and D) Generally, this means that the tape should experience at least 15 psi (100 kPa) in roll down or platen pressure. (Sources- page #4)
- After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature, approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours. In some cases, bond strength can be increased and ultimate bond strength can be achieved more quickly by exposure of the bond to elevated temperatures(e.g. 150°F [66°C] for 1 hour).
NOTE: These cleaner solutions contain greater than 250 g/I of volatile organic compounds (VOC). Please consult your local Air Quality Regulations to be sure the cleaner is compliant. When using solvents, be sure to follow the manufacturer’s precautions and directions for use when handling such materials.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Power Adapter information :
Model No.:ADS-25D-12 12018E
IN PUT:100-240V-50/60Hz 0.6A
OUTPUT:12V 1.5A
NOTE: Operating Temperature: 0-50°C Dealers License No. : XXXXXXXXXXXX
Qbic Technology Co., Ltd.
2 6 F.-1 2,No.99.Sec.1, Xintai 5th Rd.,
Xizhi Dist., New Taipei City 221, Taiwan(R.O.C)
Tel: 886-2-2697-2000 FAX:886-2-2697-2868