BaByliss E935E Hair Trimmers User Manual
- June 5, 2024
- BaByliss
Table of Contents
E935E Hair Trimmers
**User Manual
**
|
---|---
BABYLISS
99 avenue Aristide Briand
92120 Montrouge – France
www.babyliss.com
E935E Please read the following instructions carefully before using the appliance.
PRODUCT FEATURES
- Blades: Moving blade: stainless steel Fixed blade: stainless steel
- Precise cutting length adjustment thanks to the lever with a choice of 5 positions (1)
- Turbo function to increase cutting power if necessary (2)
- 8 numbered cutting guides (from 1 to 8): 3mm, 6mm, 9.5mm, 13mm, 16mm, 19mm, 22.5mm, and 25mm (3)
- Rechargeable or mains powered
- Power indicator light (4)
- 0/1 switch
- Styling comb, cleaning brush, blade-protector, oil, pouch
IMPORTANT INFORMATION REGARDING THE NI-MH BATTERIES OF THIS UNIT
To obtain and maintain the longest battery life possible, allow it to
charge for 16 hours approximately every three months. Moreover, the full
battery life of the unit will only be obtained after three complete recharge
cycles (one 16-hour cycle followed by two 8-hour cycles).
CHARGING THE Clipper
- Insert the charging plug into the appliance base and plug into the mains. Check that the light is on, showing that the appliance is charging.
- When the clipper is fully charged, unplug the adapter.
- A full charge will allow 30 minutes of clipper use.
- Before using the clipper for the first time, allow it to charge for 16 hours.
- Subsequent charges should be 8 hours.
USE ON THE MAINS
To use the clipper on the mains, plug the cord directly into the unit. Plug
the clipper, in the OFF position, into the mains and switch to position 1 (if
the battery is very weak, wait about 1 minute).
IMPORTANT! Only use the adapter that is supplied with the appliance.
USING THE CUTTING GUIDES
This clipper is supplied with 8 cutting guides. Important: Always ensure the appliance is switched off BEFORE attaching and/or removing a comb guide.
- To attach the guide, first, place it over the teeth of the clipper and then press on the rear of the guide until it clicks into position.
- To remove it, detach the rear of the guide and lift off.
ADJUSTMENT LEVER
The adjustment lever has a choice of 5 positions, enabling even more precise
cutting length adjustment.
- To increase cutting length, lower the lever.
- To reduce the cutting length, raise the lever.
TURBO FUNCTION
To boost cutting power, you can activate the turbo function by pressing the turbo button. The increased power and cutting speed thus obtained will allow you to continue to cut even the most difficult cutting zones.
PREPARATION
- Make sure blades are clean before each use.
- If possible, use the clipper on clean, dry, and tangle-free hair.
- Make sure the clipper is sufficiently charged or correctly plugged in.
NB: do not use it for more than 20 minutes continuously.
MAINTENANCE
For optimal performance, the appliance must be cleaned after each use:
-
Remove the cutting guide, rinse them under running water and dry thoroughly before storage.
-
The cutting blades can be removed to facilitate cleaning. To remove them, hold the clipper vertically and press the lower blade upwards. (FIG. 1)
– Do not unscrew the blades. -
Use the cleaning brush to remove hair.
-
To reposition the blades, make sure that the adjustment lever is in the lower position. Position the blades on the clipper head and press until they click into place. (FIG. 2)
-
Regular blade maintenance is required to ensure that your clipper performs correctly. To do so, only use the oil supplied. Switch on the clipper and place a few drops of oil on the blades. The oil supplied is specially formulated for clippers, it will not evaporate or slow the clipper blades down.
Машинка для стрижки
Производитель: BaByliss
99 Авеню Аристид Бриан
92120, Монруж, Франция
Факс 33 (0) 1 46 56 47 52
Сделано в Китае
Дата производства (неделя, год): см. на товаре
ithalatci Firma: Ertek Elektrikli Ev Aletleri San ye
Tic. A.S.
Istiklal Cad. Odakule is Merkezi.
Kat: 7/A 34430 Beyoglu – Istanbul
Tel: 0212 293 17 07
Kullanim timrii: 7 yil
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>