Altronix eBridge100RMT IP and PoE+ over Coax or Extended Ethernet Cable Installation Guide

eBridge100RMT Kit IP and PoE+ over
Coax or Extended Ethernet Cable
eBridge100RM Receiver and eBridge100TM Transceiver Kit
Installation Guide

Installing Company:
Service Rep. Name:
Address: _____
Phone #: __

Overview:

Altronix eBridge100RMT is a versatile dual solution Ethernet adapter/media converter kit that transmits data at 100Mbps full duplex and power over Coax cable or extended CAT5e cable in a PoE+ compliant format. The eBridge100RM is powered via a PoE midspan such as the Altronix Netway series or by an endspan. The receiver passes the PoE(+) compliant power over cable to the eBridge100TM transceiver which in turn passes this power to an enabled IP Camera/device. These plug-and-play units facilitate cost-effective solutions for IP devices that need to be installed at distances greater than 100m. They also provide a simple way to replace legacy analog products with new IP devices over existing coax or structured cable.

Features:

Agency Listings:

• UL/cUL Listed for Information Technology Equipment (UL 60950-1).
• CE European Conformity.
• -Tick compliant.

Input eBridge100RM:

• Powered by midspan or endspan.
  PoE compliant to IEEE 802.3af (15W) and
  PoE+ compliant to IEEE 802.3at (30W).

Ethernet:

• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5.
• Distance: up to 500m.
• Speed: 10/100BaseT, half/full duplex, auto negotiation. PoE compliant to IEEE 802.3af (15W) and PoE+ compliant to IEEE 802.3at (30W) Delivered to camera by eBridge100TM. Power provided byveBridge100RM to eBridge100TM by PoE protocol.*
• Throughput is rated to pass 100Mbps of data at distances up to 500m.

Coax Link:

• Distance: Coax 300m (Maximum Length of Coax
  Type vs. Camera Power/PoE Class, pg. 4) for power delivery.

• Connectivity: BNC, RG-59/U or similar.

Coax or CAT5e Link:

• Distance: CAT5e up to 500m, Coax 300m
  (Maximum Length of Coax or CAT5 Type vs.Camera
  Power/PoE Class, pg. 4) for power delivery.
  *See note on the bottom of Page 3.

LED Indicators:

• eBridge100RM and eBridge100TM: Green – PoE ON (by respective RJ45 jack).
• eBridge100RM and eBridge100TM: Yellow and Green LED (RJ45) IP Link status, 10/100Base-T/active.

Environmental:

• Operating Temperature:
  eBridge100RM: – 20ºC to 49ºC (– 4ºF to 120.2ºF).
  eBridge100TM: – 20ºC to 49ºC (– 4ºF to 120.2ºF).

• Storage Temperature: – 30ºC to 70ºC (– 22ºF to 158ºF).

• Humidity: 20 to 85%, non-condensing.

Functions:

• Auto detection and protection of legacy non-PoE cameras/devices.

Applications:

• Retrofit digital IP cameras in an analog CCTV installation.
• Works with Megapixel, HD720, HD1080, and VGA (SD) cameras (see a note, pg. 3).
• Extend Network link distance in an industrial environment over 700m (see a note, pg. 3).
•  Upgrade deployed CCTV Coax to a digital network in Retail, Casinos, Airports, Schools, Hospitals, etc.

Mechanical:

• Dimensions (W x L x H approx.): eBridge100RM/eBridge100TM: 3.5” x 4.375” x 1” (88.9mm x 111.1mm x 25.4mm).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. eBridge100TM and eBridge100RM are not intended to be connected to outside plant leads and should be installed indoors within the protected premises. eBridge100TM and eBridge100RM are intended for indoor use only.
Note: The eBridge100RM and eBridge100TM are a paired set and must be used together.

1. eBridge100RM installation:
   a. Secure the unit to the desired mounting surface with a proper fastening device utilizing the unit’s mounting hole (Fig. 2a, pg. 4). Unit should be mounted in proximity to an ethernet switch/network, NVR, or video server.
   Note: When installing more than one (1) eBridge100RM, please allow at least 1” (25mm) distance between the receivers.
   b. Connect the structured cable from Ethernet midspan or endspan device to RJ45 jack marked [PoE Input] (Fig. 2, pg. 4).
   c. When connecting to the eBridge100TM use either Coax or CAT5 or higher wiring:
   Coax: Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 3).
   CAT5 or higher: Connect CAT5 or higher to the connector marked [RJ45 OUT] (Fig. 2, pg. 4).

2.  eBridge100TM installation:
   a. Secure unit to the desired mounting surface with a proper fastening device utilizing the case’s mounting hole (Fig. 2a, pg. 4). Unit should be mounted in proximity of the camera/device.
   b. Connect the structured cable from the IP camera/device to the RJ45 jack marked [PoE Out] (Fig. 2, pg. 4).
   c. Coax: Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 4).
   CAT5 or higher: Connect CAT5 or higher to the connector marked [RJ45 IN] (Fig. 2, pg. 4).

Note: The eBridge100RMT is designed to accommodate Megapixel, HD720, HD1080, and VGA (SD) cameras. It is important to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may show pixelation and latency. It is advisable to pretest the system if unsure. Alternatively, frame rate and resolution may be reduced to accommodate system equipment.

Technical Specifications:

IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W).
Indicators| Yellow (RJ45 connector): On-Link, Off – No Link, Blinking – Activity.
Green (RJ45 connector): On – 100Base-TX, Off – 10Base-T.
Green: PoE Active.
Environmental Conditions| Operating Ambient Temperature (UL60950-1): eBridgelOORM: – 20°C to 49°C (— 4°F to 120.2°F).
Bridget 00TM: – 20°C to 49°C (— 4°F to 120.2°F)
Storage Temperature: — 30°C to 70°C (— 22°F to 158°F).
Relative humidity: 85% +1— 5%
Operating Altitude: — 304.8 to 2,000m.
Regulatory Compliance| UL/cUL Listed for Information Technology Equipment (UL 60950-1).
CE European Conformity C-Tick compliant.
Weights (approx.)| Product: 0.45 lb. (0.2 kg) I Shipping: 0.8 lb. (0.36 kg)

*Note: Caution: once PoE connection is established between eBridge100RM and eBridge100TM, disconnection from eBridge100TM will not disable the PoE output voltage on the eBridge100RM, although the eBridge100TM can be reconnected, caution should be taken not to connect the CAT5 or single UTP wiring from eBridge100RM to any non-PoE device.

Maximum Length of Coax/CAT5 Type vs. Camera Power/PoE Class:

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty
IIeBridge100RMT G19U

MEMBER
eBridge100RMT Installation Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>