JOHN DEERE MX00654 Select Series Lawn Tractors Instruction Manual

JOHN DEERE MX00654 Select Series Lawn Tractors

Specifications:

• Model: MX00654
• Date: 20170510

Product Information

Thank you for purchasing a John Deere product. Your machine was designed and built to be operated safely in lawn mowing operations.
It is essential to follow all safety instructions and operating guidelines provided in the operator’s manual to prevent serious injuries or accidents.

Product Usage Instructions

Before Using Your Machine:

1. Read the operator’s manual, watch the safety video, and review safety signs.
2. Ensure everyone using the machine understands how to operate it safely.
3. Perform daily checks as outlined in the General Instructions section.
4. Follow instructions in Preventing Injuries, Protect Children, Operating on Slopes and Near Terrain Hazards, Avoid Thrown Objects, and Prevent Fires sections.

Machine Operation:
This machine is intended for customary lawn mowing operations only. Ensure strict adherence to manufacturer’s conditions of operation, service, and repair. Only operate, service, and repair the machine if you are familiar with its characteristics and safety rules.

Machine Servicing and Inspection:
Understand how to service and inspect your machine properly. If you have any doubts or questions, contact your dealer for assistance.

FAQ:

1. Q: Can I use the machine for purposes other than lawn mowing?
   A: No, the machine is designed solely for customary lawn mowing operations. Any other use is considered misuse and may result in damage or injury.

2. Q: Who should operate, service, and repair the machine?
   A: Only persons familiar with the machine’s characteristics and safety rules should operate, service, and repair it. Strict adherence to safety regulations is essential.

Thank You for Purchasing a John Deere Product
We appreciate having you as a customer and wish you many years of safe and satisfied use of your machine.
MX00654,000020B-19-20170510

Using Your Operator’s Manual

Read this operator’s manual, watch the safety video, and review the safety signs on your machine before use. They all contain important safety information and operating instructions that must be followed to help keep you and others safe. Be sure everyone who uses the machine has read the manual, reviewed the safety signs, and knows how to use the machine safely and properly.
Your machine was designed and built to be operated in accordance with all the safe operating instructions. Since it was designed to cut grass, it can amputate hands and feet and throw objects. If you do not follow safety instructions, serious injury or death can occur.
This operator manual is organized in sections to help you find information quickly. You can use this manual to find answers to many of your operating and servicing questions. An index at the end of this book helps you find needed information quickly. Contact your dealer if this manual does not answer your questions.

Before using your machine:

• Know how to operate the machine. The Operating Controls section helps you understand the controls of your machine and what they do.
• Prepare your machine and the mowing area by performing required daily checks outlined in the General Instructions section.
• Follow instructions in the Preventing Injuries section, especially related to:
  • Keeping children safe by following instructions in the Protect Children section.
  • Avoiding injury on slopes and near terrain hazards by following instructions in the Operating on Slopes and Near Terrain Hazards section.
  • Follow the instructions in the Avoid Thrown Objects section and keep all guards in place, including discharge chute.
  • Cleaning machine during use and before storing as outlined in the Prevent Fires section.
• Understand how to service and inspect your machine.

If you do not understand the instructions or have questions, contact your dealer.
The machine shown in this manual can differ slightly from your machine.
RIGHT-HAND and LEFT-HAND sides are determined by facing in the direction that the machine travels when going forward. When you see a broken line (——), the item referenced is hidden from view.
Before delivering this machine, your dealer performed a predelivery inspection to ensure best performance.
This manual is an important part of your machine. Keep this manual with the machine when you sell it.
OUO2005,000078D-19-20200211

Machine Use

• This machine is designed solely for use in customary lawn mowing operations. Use in any other way is considered as contrary to the intended use.
• The manufacturer accepts no liability for damage or injury resulting from this misuse, and these risks must be borne solely by the user.
• Compliance with and strict adherence to the conditions of operation, service, and repair as specified by the manufacturer also constitute essential elements for the intended use.
• This machine should be operated, serviced, and repaired only by persons familiar with all its particular characteristics and acquainted with the relevant safety rules (accident prevention).
• The accident prevention regulations, all other generally recognized regulations on safety and occupational medicine, and the road traffic regulations must be observed at all times.
• Setting fuel delivery beyond published factory specifications or otherwise overpowering will result in loss of warranty protection for this machine.
• Any arbitrary modifications carried out on this machine will relieve the manufacturer of all liability for any resulting damage or injury.

OUO1023,0000025-19-20170605

Special Messages

Your manual contains special messages to bring attention to potential safety concerns and machine damage, as well as helpful operating and servicing information. Please read all the information carefully to avoid injury and machine damage.

CAUTION:
Avoid injury! This symbol and text highlight potential hazards or death to the operator or bystanders that may occur if the hazards or procedures are ignored.

IMPORTANT:
Avoid damage! This text is used to tell the operator of actions or conditions that might result in damage to the machine.

NOTE:
General information is given throughout the manual that may help the operator in the operation or service of the machine.
MX00654,000020D-19-20170605

Service Literature
If you would like to purchase a copy of the Parts Catalog or Technical Manual for this machine, visit The John Deere Technical Information Store at:
https://techpubs.deere.com/
or call:
U.S. & Canada: 1-800-522-7448.
All Other Regions: Your John Deere dealer.
TH84124,0000199-19-20200205

Parts

We recommend John Deere quality parts and lubricants, available at your John Deere dealer. When you order parts, your John Deere dealer needs the serial number or product identification number (PIN) for your machine or attachment. These are the numbers that you recorded in the Product Identification section of this manual.

Order Service Parts Online
Visit http://JDParts.deere.com for your Internet connection to parts ordering and information.
TC00531,00000E9-19-20150306

Product Compatibility

The MulchControl kit is compatible with:

42 in, 48 in, and 54 in Accel Deep™ decks for X300 models.
42 in, 48 in, and 54 in Accel Deep™ decks for X500 models.
48 in Accel Deep™ deck for X700 models and X900 models.
42 in, 48 in, and 54 in Accel Deep™ decks for ZTrak™ models.
42 in and 48 in Accel Deep™ decks for S200 models.

MG39705,00002E5-19-20200220

Record Purchase Information
Record your purchase information in the spaces provided below.
DATE OF PURCHASE:
DEALER NAME:
DEALER PHONE: _____

OUMX258,0000CEA-19-20131203

Read Safety in Machine Operator’s Manual
Read the general safety operating precautions in your machine operator’s manual for additional safety information.
OUMX068,0000230-19-20130918

Parking Safely

Always apply the park brake and remove the key before leaving the machine unattended. Children or others may attempt to move or operate an unattended machine.

• Stop the machine on a level surface.
• Disengage mower blades or other attachments.
• Lower attachments to the ground.
• Apply the park brake.
• Stop the engine.
• Remove the key.
• Wait for engine and all moving parts to stop before you leave the seat.

OUO2005,0000788-19-20200215

Protect Children

MXAL41929-UN: Protect children warning symbol

• Children can be killed or seriously injured by riding mowers when operators do not follow safe operating practices.
• Do not mow in reverse. Operating with the mower engaged while backing up is discouraged.
• Never give children a ride on a mower or in a cart behind the mower, even when the blades are off. They can fall off and be run over or cut by the mower blades.
• Children can interfere with mower operation. Children who have been given rides in the past can suddenly appear in the mowing area for another ride. If you are not aware, they can be run over or backed over by the mower.
• Children are often attracted to lawn mowers and mowing activities, especially if they have been given rides before. They do not know if the blades are rotating or understand that they can be killed or seriously injured even if the blades are not rotating.
• Keep children indoors and out of the mowing area when the mower is being operated. Keep children under the watchful eye of a responsible adult, other than the operator. If there is not a responsible adult to ensure that children stay indoors, DO NOT mow. Be alert to the presence of children or others. Turn off the mower blades and stop the machine if someone enters the mowing area.
• Look in the direction the machine is traveling. Before and while backing, turn off the mower blades and look down and behind the machine carefully, especially for children. Use extreme care when approaching objects that block your view, such as blind corners, shrubs, or trees, especially while backing. They can hide a child.

MX00654,00002ED-19-20200330

Service and Maintenance

• Proper service and maintenance of the machine is essential.
• Keep all parts in good condition, keep all nuts and bolts tight, and repair any damage immediately. Stop and inspect the machine immediately if you strike an object. Ensure that all safety devices, discharge chute, and grass catcher components are in good condition and replace when necessary.
• Understand service procedures thoroughly before working on the machine. If you do not understand the service procedures or are uncomfortable working in your machine, contact your servicing dealer.
• Disconnect the battery or all spark plug wires before servicing the machine. Disconnect negative terminal first and positive last. Install positive terminal first and negative last. Some components could have stored energy in springs or hydraulic components. Servicing procedures described in the Service section describe how to perform service and maintenance tasks safely.
• Support any machine elements that must be raised for service work. Use jack stands or service locks to support components when needed.

MX00654,00002EE-19-20200330

Disposing of Waste Products and Chemicals

• Waste products, such as used oil, fuel, coolant, brake fluid, and batteries can harm the environment and people.
• Do not use beverage containers for waste fluids – someone can mistakenly drink from them.
• A Safety Data Sheet (SDS) provides specific details on chemical products: Physical and health hazards, safety procedures, and emergency response techniques. The seller of the chemical products used with your machine is responsible for providing the SDS for that product.
• To learn how to recycle or properly dispose of waste products generated from service, see your local recycling center or authorized dealer. If you wish to discard the machine, contact your local recycling center or authorized dealer.

MX00654,00002EF-19-20200330

Switching to Open and Closed Modes

CAUTION:
Avoid injury! Rotating belts and blades are dangerous.

1. Park machine on a level surface.
2. Disengage mower blades.
3. Lock the park brake.
4. Wait for all moving mower deck parts to stop before you leave the operator’s station. APY24916-UN: MulchControl™ handle shown
5. Rotate lever clockwise (A) to close or counterclockwise (B) to open.

MG39705,0000293-19-20200522

Unplugging Mower

CAUTION:
Avoid injury! Do not attempt to unplug attachment with machine running.
Rotating blades are dangerous. Shut off the engine and remove the key before getting off the seat to inspect the machine and attachment
Thrown objects can cause serious injury. Make sure that all machine parts are stopped before raising hopper top or removing chutes.

1. Park machine safely. Wait for all moving parts to stop before you leave the operator platform to inspect machine.
2. Check under mower deck and discharge chute for debris.
3. Clear all debris before using mower.
4. If plugging is occurring switch to open mode to allow some grass to discharge.

OUO2004,0000AF8-19-20141112

Removing Mower

(See Removing Mower section in Vehicle/Mower Deck OM) Clear all debris from under mower deck and discharge chute.
MG39705,0000446-19-20200525

Remove Shields, European Models Only (ZTrak™)

MXT014809-UN: Picture Note: 42 in. Accel Deep™ deck shown.

MXT014810-UN: Picture Note: 48 in. Accel Deep™ deck shown.

1. Remove self-tapping screw (A) and cover plate (B).

OUMX068,0000CFC-19-20160307

Remove Shields, European Models Only (42 in Accel Deep™ Decks—X300 and X500)

1. NOTE:
   Hardware (A) is retained to shield with a push nut. MXT014811-UN: Right Side Deck Shield
   Remove right shield (B).

2. APY30208-UN: .
   Flip shield over and cut out as indicated (C) above.

MG39705,00002EF-19-20200220

Remove Shields, European Models Only (X700 and X900)

1. NOTE:
   Hardware (A) is retained to shield with a push nut. MXT014813-UN: Deck Shields
   Remove right (B) and left (C) shield.

2. Cut out along marking (D) in left shield.

MG39705,00002F0-19-20200123

Removing Discharge Blades

CAUTION:
Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.

1. Turn mower deck so underside is face up.
2. Insert wood block between blade and mower deck to prevent blade from turning when removing bolt.
3. MXT012577-UN: Blade Removal
   Remove bolt (A), large washer, (B) and blade (C).

OUO2004,0000A9D-19-20150730

Parts in Kit

IMPORTANT:
The mulching blades for the 42 Inch Accel Deep Mower MUST be used only with the mulch plug insert. Use of Standard or Bagging blades WILL destroy the mulch plug and may damage the tractor and mower deck.

APY24917-UN:
Parts in Kit

MG39705,0000294-19-20200416

Installing MulchControl™ Discharge Plate

CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

NOTE:
For ease of installation, place mower deck in the vertical position.

• The following procedure is for the 42 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 42 in Accel Deep™ deck is similar.

1. APY24918-UN: .
   Position discharge plate (A) as shown.

2. Install discharge plate to the metal chute (B) and toe guard (C) with two M8 x 20 carriage bolts (D) and two M8 lock nuts.

3. Tighten lock nuts.

(15 lb·ft)

MG39705,0000295-19-20200602

Installing Deflector Assembly

CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

NOTE:
For ease of installation, place mower deck in the vertical position.

• The following procedure is for the 42 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 42 in Accel Deep™ deck is similar.

1. APY24920-UN: .
   Assemble kit gate (A) and baffle (C) together as shown and insert the pin (B) in the slots.

2. Install deflector assembly (A) to the mower deck using M8 shoulder bolts (B), M8 lock nuts (D), and lock nut (E).

3. Ensure the pin (C) is in the correct slot and gate door can open and close.

4. Tighten lock nuts (D) and lock nut (E).

(15 lb·ft)

NOTE:
For 200 series model, do not use M8 lock nut (E).

• MulchControl is a trademark of Deere & Company
• Select Series is a trademark of Deere & Company
• Accel Deep is a trademark of Deere & Company

MG39705,0000296-19-20200602

Installing Handle Assembly (For X3, X5, and Z3 Models)

NOTE:
The following procedure is for the 42 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines listed above with a 42 in Accel Deep™ deck is similar.

CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

1. Install handle assembly (A) to hinge pin with M8 lock nut (B). Tighten lock nut until snug on handle.
2. On the top side of deck, install M8 lock nut (C) on shoulder bolt (D) to secure handle assembly.

(15 lb·ft)

MG39705,0000297-19-20200602

Installing Handle Assembly (For S200 Models)

CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

1. Install detent plate (A) and secure with two M8 shoulder bolts (C) from the bottom side to the mower deck and M8 lock nuts (B) on the detent plate (A).
2. Install handle assembly (D) through a slot in detent plate (A) and secure it with M8 lock nut (E) and two washers (F).

(15 lb·ft)

NOTE:
Handle assembly is spring loaded. Apply pressure to handle mounting plate for proper installation.
MG39705,00002F4-19-20200602

Installing Mulch Blades

CAUTION:
Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.

1. Install blade (A) with cutting edge toward the ground.
2. Install large washer (B) and bolt (C).
3. Insert wood block between blade and mower to prevent blade from turning when tightening bolt.
   Item| Measurement| Specification
   ---|---|---
   Blade Bolt| Torque| 68 N·m
   (50 lb·ft)
4. Tighten bolt.
5. To check blade-to-mulch baffle clearance, rotate blades by hand. If interference occurs, check that hardware is tightened.

OUMX068,0000D92-19-20160307

Install Shields, European Models Only (42 in. Accel Deep™ Decks—X300 and

X500)

NOTE:
Hardware (B) is retained to shield with a push nut.

1. Install right shield (A) with attached hardware (B).
2. Check for clearance between handle assembly (C) and shield.
3. If necessary, remove shield and cut away excess material.

MG39705,00002F1-19-20200123

Installing Label

Place label (A) on mower deck as shown to provide visual indication of door direction.
MG39705,0000298-19-20191211

Installing Mower
(See Installing Mower section in Vehicle/Mower Deck OM.)
OUMX068,0000D95-19-20160307

Parts in Kit
IMPORTANT:
The mulching blades for the 48 Inch Accel Deep Mower MUST be used only with the mulch plug insert. Use of Standard or Bagging blades WILL destroy the mulch plug and may damage the tractor and mower deck.

Parts in Kit

MG39705,0000299-19-20200602

Installing MulchControl™ Discharge Plate
CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

NOTE:
For ease of installation, place mower deck in the vertical position.

• The following procedure is for the 48 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 48 in Accel Deep™ deck is similar.

1. Position discharge plate (A) as shown.
2. Insert M8 x 20 carriage bolt (B) through the mower deck and into the hole in the discharge plate.
3. Install M8 lock nut on bolt (B).
4. Insert M8 shoulder bolt (C) through the discharge plate and into the hole in the mower deck.
5. Install M8 lock nut on bolt (C).
6. Tighten lock nuts.

(15 lb·ft)

MG39705,000029A-19-20200602

• MulchControl is a trademark of Deere & Company
• Select Series is a trademark of Deere & Company
• Accel Deep is a trademark of Deere & Company

Installing Deflector Assembly
CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

NOTE:
For ease of installation, place mower deck in the vertical position.

• The following procedure is for the 48 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 48 in Accel Deep™ deck is similar.

1. Assemble kit gate (A) and baffle (C) together as shown and insert the pin (B) in the slots.

2. Install right deflector assembly (D) to the mower deck using M8 shoulder bolts (F) and M8 lock nuts.

3. Ensure the pin (E) is in the correct slot and gate door can open and close.

4. Tighten lock nuts.
   Item| Measurement| Specification
   ---|---|---
   M8 Lock Nut| Torque| 20 N·m
   (15 lb·ft)

5. Install left deflector assembly (I) as shown, to the mower deck using M8 shoulder bolts (H) and M8 lock nuts.

6. On the top side of deck, install M8 lock nut on shoulder bolt (G).

7. Tighten lock nuts.

(15 lb·ft)

MG39705,000029B-19-20200602

• MulchControl is a trademark of Deere & Company
• Select Series is a trademark of Deere & Company
• Accel Deep is a trademark of Deere & Company

Installing Handle Assembly
NOTE:
The following procedure is for the 48 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 48 in Accel Deep™ deck is similar.

CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

1. Install handle assembly (A) to hinge pin with M8 lock nut (B). Tighten lock nut until snug on handle.
2. On the top side of deck, install M8 lock nut (C) on shoulder bolt (D) to secure handle assembly.

(15 lb·ft)

MG39705,000029C-19-20200602

Installing Mulch Blades
CAUTION:
Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.

1. Install blade (A) with cutting edge toward the ground.
2. Install large washer (B) and bolt (C).
3. Insert wood block between blade and mower to prevent blade from turning when tightening bolt.
4. Tighten bolt.
   Item| Measurement| Specification
   ---|---|---
   Blade Bolt| Torque| 68 N·m
   (50 lb·ft)
5. To check blade-to-mulch baffle clearance, rotate blades by hand. If interference occurs, check that hardware is tightened.

OUMX068,0000D93-19-20160307

Install Shields, European Models Only (X700/X900)
NOTE:
Hardware (C) is retained to shield with a push nut.

1. Install left (A) and right (B) shield with attached hardware (C).
2. Check for clearance between handle assembly (D) and shield (A).
3. If necessary, remove shield and cut away excess material.

MG39705,00002F3-19-20200213

Installing Label

APY24933-UN: Domestic Mower Deck is Shown.

APY24934-UN: Export Mower Deck is Shown.
Place label (A) on mower deck as shown to provide visual indication of door direction.
MG39705,000029D-19-20200109

Installing Mower
(See Installing Mower section in Vehicle/Mower Deck OM.)
OUMX068,0000D96-19-20160307

Parts in Kit
IMPORTANT:
The mulching blades for the 54 Inch Accel Deep Mower MUST be used only with the mulch plug insert. Use of Standard or Bagging blades WILL destroy the mulch plug and may damage the tractor and mower deck.

Parts in Kit

MG39705,000029E-19-20200602

Installing MulchControl™ Discharge Plate
CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

NOTE:
For ease of installation, place mower deck in the vertical position.

• The following procedure is for the 54 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 54 in Accel Deep™ deck is similar.

1. Position discharge plate (A) as shown.
2. Insert M8 x 20 bolt (B) through the mower deck and into the hole in the discharge plate.
3. Install M8 lock nut on bolt. Do not tighten yet.
4. Insert M8 shoulder bolt (C) through the discharge plate and into the hole in the mower deck.
5. Install M8 lock nut on bolts.
6. Tighten lock nuts.

(15 lb·ft)

MG39705,000029F-19-20200602

Installing Deflector Assembly
CAUTION:

Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

NOTE:
For ease of installation, place mower deck in the vertical position.

• The following procedure is for the 54 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 54 in Accel Deep™ deck is similar.

1. Assemble kit gate (A) and baffle (C) together as shown and insert the pin (B) in the slots.

2. Install right deflector assembly (D) to the mower deck using M8 shoulder bolts (F) and M8 lock nuts.

3. Ensure the pin (E) is in the correct slot and gate door can open and close.

4. Tighten lock nuts.
   Item| Measurement| Specification
   ---|---|---
   M8 Lock Nut| Torque| 20 N·m
   (15 lb·ft)

5. Install left deflector assembly (I) as shown, to the mower deck using M8 bolts (H) and M8 lock nuts.

6. On the top side of deck, install M8 lock nut on shoulder bolt (G).

7. Tighten lock nuts.

(15 lb·ft)

MG39705,00002A0-19-20200602

• MulchControl is a trademark of Deere & Company
• Select Series is a trademark of Deere & Company
• Accel Deep is a trademark of Deere & Company

Installing Handle Assembly
NOTE:
The following procedure is for the 54 in MulchControl™ on a Select Series™ mower deck. The installation procedure for other machines with a 54 in Accel Deep™ deck is similar.

CAUTION:
Avoid injury! Machine component or attachment is heavy. Use a safe lifting device or get an assistant to help lift, install, or remove component or attachment.

1. Install handle assembly (A) to hinge pin with M8 lock nut (B). Tighten lock nut until snug onto handle.
2. On the top side of deck, install M8 lock nut (C) on shoulder bolt (D) to secure handle assembly.

(15 lb·ft)

MG39705,00002A1-19-20200602

Installing Mulch Blades
CAUTION:
Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.

1. Install blade (A) with cutting edge toward the ground.
2. Install large washer (B) and bolt (C).
3. Insert wood block between blade and mower to prevent blade from turning when tightening bolt.
4. Tighten bolt.
   Item| Measurement| Specification
   ---|---|---
   Blade Bolt| Torque| 68 N·m
   (50 lb·ft)
5. To check blade-to-mulch baffle clearance, rotate blades by hand. If interference occurs, check that hardware is tightened.

OUMX068,0000D94-19-20160307

Installing Label

Place label (A) on mower deck as shown to provide visual indication of door direction.
MG39705,00002A2-19-20191212

Installing Mower
(See Installing Mower section in Vehicle/Mower Deck OM.)
OUMX068,0000D97-19-20160307

Removing MulchControl™ (42 Inch Accel Deep™ Decks)

Removing MulchControl™

1. Remove mower deck. (See Removing Mower section in Vehicle/Mower Deck Operator Manual).

2. For Select Series™ 42 in Accel Deep™ European mowers only, remove right belt shield.

3. CAUTION:
   Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.
   Remove mulch blades.

4. Remove discharge plate (B) from discharge area by removing the carriage bolts (A) and lock nuts.

5. CAUTION:
   Avoid injury! Components are installed under spring tension. Wear eye protection and use proper tools when installing and removing components with spring tension. Loosen lock nuts (D) and remove the handle assembly (C).

6. Loosen M8 lock nuts (E).

7. Remove shoulder bolts (F) and remove deflector assembly (G)

8. ZTrak™ export only: Reinstall cover plate.

Storing MulchControl™
Clean and store all MulchControl™ parts in a clean, dry place.
MG39705,00002B3-19-20200128

Removing MulchControl™ (48 Inch Accel Deep™ Decks)
Removing MulchControl™

1. Remove mower deck. (See Removing Mower section in Vehicle/Mower Deck Operator Manual).

2. For X700/X900 48 in Accel Deep™ European mowers only, remove right belt shield.

3. CAUTION:
   Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.
   Remove mulch blades.

4. Remove discharge plate (B) from discharge area by removing the hex flange bolts (A) and lock nuts.

5. Loosen lock nuts (D) and remove the handle assembly (C).

6. Loosen lock nuts (E) and remove M8 bolts and then remove the LHS deflector assembly (F).

7. Loosen lock nuts (H) and remove M8 bolts and then remove the RHS deflector assembly (G).

8. X700/X900 export only: Install hardware into any exposed holes that remain in deck after removal of MulchControl™ kit.

9. ZTrak™ export only: Reinstall cover plate.

Storing MulchControl™
Clean and store all MulchControl™ parts in a clean, dry place.
MG39705,00002B4-19-20200127

Removing MulchControl™ (54 Inch Accel Deep™ Decks)
Removing MulchControl™

1. Remove mower deck. (See Removing Mower section in Vehicle/Mower Deck Operator Manual).

2. CAUTION:
   Avoid injury! Blades are sharp. Always wear gloves when handling blades or working near blades. Replace blades if defective. Never straighten or weld them.
   Remove mulch blades.

3. Remove discharge plate (B) from discharge area by removing the carriage bolts (A) and lock nuts.

4. Loosen lock nuts (D) and remove the handle assembly (C).

5. Loosen lock nuts (E) and remove M8 bolts and then remove the LHS deflector assembly (F).

6. Loosen lock nuts (H) and remove M8 bolts, and then remove the RHS deflector assembly (G).

Storing MulchControl™
Clean and store all MulchControl™ parts in a clean, dry place.
MG39705,00002B5-19-20200128

Using Troubleshooting Chart

If you are experiencing a problem that is not listed in this chart, see your authorized dealer for service. When you have checked all the possible causes listed and you are still experiencing the problem, see your authorized dealer.
BS62576,00014F0-19-20130919

MulchControl™
Troubleshooting Chart

seated firmly onto pin taper and properly aligned.
MulchControl™ causing blowout in closed position| Check that gate stop is installed (after removal of cut and throw – 42 in. Accel Deep™ only) Ensure that system is in closed position
MulchControl™ Material Dispersion Not Satisfactory| Clean debris buildup from underside of deck Check blades for sharpness and damage
Ensure that correct blades are installed (MulchControl™ is designed to use mulch blades, not standard blades)
Change blades
Check discharge chute for damage
Check procedures on Adjusting Mower Level Side-to- Side and Front-to-Rear.
Adjust system for proper door position Run engine at fast throttle
Mowing too fast for grass conditions
---|---

MG39705,00002F2-19-20200127

John Deere Quality

John Deere equipment is more than just a purchase, it’s an investment in quality. That quality goes beyond our equipment to your John Deere dealer’s parts and service support. This support is needed to keep you a satisfied customer.
That’s why John Deere has initiated a process to handle your questions or problems, should they arise. The following three steps will help guide you through the process.

Step 1
Refer to your operator’s manual

• It has many illustrations and detailed information on the safe and proper operation of your equipment.
• It gives troubleshooting procedures, and specification information.
• It gives ordering information for parts catalogs, service and technical manuals.
• If your questions are not answered in the operator’s manual, then go to Step 2.

Step 2
Contact your dealer

• Your John Deere dealer has the responsibility, authority, and ability to answer questions, resolve problems, and fulfill your parts and service needs.
• First, discuss your questions or problems with your dealer’s trained parts and service staff.
• If the parts and service people are unable to resolve your problem, see the dealership manager or owner.
• If your questions or problems are not resolved by the dealer, then go to Step 3.

Step 3
Contact John Deere

• Your John Deere dealer is the most efficient source in addressing any concern, but if you are not able to resolve your problem after checking your operator’s manual and contacting your dealer, contact John Deere for assistance.
• For prompt, effective service, please have the following ready before you call:
  • The name of the dealer with whom you’ve been working.
  • Your equipment model number.
  • Number of hours on machine (if applicable).
  • Your serial number which you recorded on the inside front cover of this manual. If the problem is with an attachment, your attachment identification number.
•  Then call 1-800-537-8233 (United States and Canada) and our advisor will work with your dealer to investigate your concern. If you are outside the United States and Canada, visit the following website:

http://www.deere.com/globalhome/deerecom/global_home.page?CC=true
Select your country and then click on the Contact Us link.
SP66632,00043A7-19-20170510
Copyright © 2024 Deere & Company. All Rights Reserved.

References

• JDParts.deere.com
• John Deere US | Products & Services Information
• John Deere - Technical Information Store - Technical Information Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>