JOHN DEERE IQ Keypad-PG Touch Keypad User Guide
- May 15, 2024
- John Deere
Table of Contents
JOHN DEERE IQ Keypad-PG Touch Keypad
IQ Keypad is a battery-powered, capacitive touch keypad for use with compatible IQ4 NS, IQ4 Hub & IQ Panel 4 platforms via the PowerG protocol. It provides an easy and intuitive interface to control the basic features of the system. This manual covers both IQ Keypad-PG and IQ Keypad Prox-PG models.
USING YOUR SYSTEM: OVERVIEW
USING YOUR IQ KEYPAD
KEYPAD STATUS LIGHTS
Status lights help you understand the state of the system at a glance.
ARMING KEYS
Arming keys are the primary way of controlling the system from the IQ Keypad.
NOTE
Press and hold the arming keys for two seconds. If successful, the Armed
Status LED will flash twice. If communication is not successful, the keypad
flashes all keypad number LEDs (backlight) 0.5 seconds ON/OFF twice.
SECURE ARMING
When Secure Arming is enabled on the primary panel, a valid 4 – 6 digit user
code is required to Arm the system.
DISARMING KEYS
Disarming from the IQ Keypad is easy. Simply enter a valid 4 – 6 digit code
into the keypad and the system will disarm.
NOTE
If successful, the Armed Status LED will flash twice. If communication is
not
successful, the keypad flashes all keypad number LEDs (backlight) for 0.5
seconds ON/
OFF twice.
PROX TAG SUPPORT
For “IQ Keypad Prox-PG” models that support Prox Tags, you may Arm with a Prox
Tag in place of a 4 – 6 digit code if Secure Arming is enabled and by pressing
the Arming icon of choice, followed by presenting your tag in front of the
bullseye icon on the lower right-hand side of the keypad. If the system is
armed, presenting a valid Prox Tag will disarm it.
EMERGENCY KEYS
Emergency keys allow you to trigger an emergency panic directly from the IQ
Keypad.
NOTE: Press and hold emergency keys for two seconds
START MENU
The Start Menu on the IQ Keypad allows access to more advanced functionality
such as silent arming, bypassing
zones, turning on/off the chime, buzzer and more. See the table below for a
list of functions
NOTE: All menus will follow the secure arming option whether an access
code is needed.
PARTITION ARMING
The Hash Menu on the IQ Keypad allows access to Partition Arming
functionality. It may also act as a “Home” button to back out of any button
press activity and start over. See the table below for a list of functions.
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
- Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. To avoid the possibility
of exceeding the FCC radio frequency exposure limits, this equipment should be
installed and operated with a minimum distance of 20 cm (7.9 inches) between
the antenna and your body during normal operation. Users must follow the
specific operating instructions to satisfy RF exposure compliance.
ISED CANADA NON-INTERFERENCE DISCLAIMER
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
- This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B).
ISED CANADA RF EXPOSURE STATEMENT
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance 20 cm between the radiator and any part of
your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>