EPSON AE-WH5674B Remote Controller Instruction Manual
- June 5, 2024
- Epson
Table of Contents
EPSON AE-WH5674B Remote Controller
Remote control rendering
Remote control physical function requirements description
Button function description
| N0. | Button | Features |
|---|---|---|
| 1 | **** | POWER |
| 2 | **** | apps |
| 3 | UP | |
| 4 | DOWN | |
| 5 | LEFT | |
| 6 | RIGHT | |
| 7 | ENTER |
button prompt command
8| | BACK| Return to the previous or previous page
9| | HOME| Return to the system level home page on any interface
10| | VOICE| (It works only after Bluetooth pairing is connected)
11| | VOL+| Increase the volume (global applies, this button has only
one operation)
12| | VOL-| Decrease the volume (global applies, this button has only
one operation)
13| | YouTube|
14| | NETFLIX|
15| | Google play|
---|---|---|---
Remote control key value
Key code value:
| Usage Page| Usage ID| IR CODE
---|---|---|---
Power| 0x0C| 0x0030| 0x1e
Back| 0x0C| 0x0224| 0x4c
Home| 0x0C| 0x0223| 0x42
Voice search| 0x0C| 0x0221| 0x79
enter（select）| 0x0C| 0x0041| 0x5f
Up| 0x0C| 0x0042| 0x03
Down| 0x0C| 0x0043| 0x5e
Left| 0x0C| 0x0044| 0x02
Right| 0x0C| 0x0045| 0x40
Voice+| 0x0C| 0x00E9| 0x5b
Voice-| 0x0C| 0x00EA| 0x18
APPS| 0x0C| 0x01A2| 0x7a
| 0x0C| 0x0078| 0x7c
| 0x0C| 0x0077| 0x77
| 0x0C| 0x0079| 0x7b
Remote control instructions
-
Special requirements for remote control
-
When Bluetooth is connected, the remote control sends the Bluetooth key value; if Bluetooth is not connected, the infrared key value is sent.
-
Indicator light: red, each time the button is pressed, the indicator light flashes.Low voltage reminder: When the battery is low, the indicator light flashes quickly. As long as it is still in operation, it will remain in the flashing state. When it is no longer operated by the remote controller, it will flash 5 times or flash 3 seconds, then stop and go out.
-
upport Bluetooth remote control online upgrade, and trigger upgrade through HOST.
-
Pairing method:
-
Press and hold the “ENTER” + “VOL-” button for 3 seconds at the same time, the indicator light flashes, and the pairing success indicator light is on for 3 seconds and then off.
-
When the pairing is not successful, if you still press the ENTER +VOL- button, the pairing broadcast will be sent all the time so that the user can pair.
-
Press the ENTER +VOL- button once to match successfully. Do not clear the pairing and then pair again. After a key pairing is successful, the pairing broadcast can no longer be sent until the next time the button is pressed.
＜12ms Connection interval＜12ms -
Remote control distance：≥10m
-
Bluetooth device name:EPSON ATV REMOTE
-
Support ” ENTER ” + “back” to upload bug report function
-
“back” + “down” to open the Accessory page
-
Pairing function requirements: there must be no problems that the Bluetooth device cannot be scanned or paired (including continuous pressing of the pairing key within a short period of time), please verify 50 times to ensure that there is no problem;
-
Reconnection function requirements: there must be no problems with the connection failure, including the box power failure and the connection, the remote control power failure and the connection, stand for 2 hours to reconnect, etc., please verify 50 times to ensure that there is no problem;
-
Anti-interference function requirements: there must be no problems that greatly affect the host’s WIFI throughput, please ensure that the host’s WIFI throughput is normal when connecting the remote control;
-
Performance requirements: It is required to support ≥10m, and there must be no voice call jams, loss, and remote control button jams, missing codes, or continuous keys;
-
Power consumption requirements: the remote control can be used continuously for at least 6 months 16Khz voice sample with 16-bit sampling Voice: 16Khz voice sample with 16-bit sampling, short press the voice button (color button) to start recording, and the remote control will stop recording after receiving the stop recording command from the voice engine. The voice timeout is protected for 30s, and the recording is forced to exit.
-
The box software can control the opening and closing of the MIC.
-
Support the remote control MIC and other MIC (such as the recording key on the phone apk) to alternate and switch voice input.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC Warning
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:(1) This device may not cause
interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d’Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d’interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les
interférences qui peuvent causer un mauvais fonctionnement de l’appareil.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>