URC Automation UR2-DTA DTA Remote Control Instruction Manual
- June 5, 2024
- URC-Automation
Table of Contents
URC Automation UR2-DTA DTA Remote Control Instruction Manual
Introduction
The UR2-DTA is designed to operate the S/A, Pace Micro, Motorola and IPTV set tops, plus the majority of TV equipment on the market as shown below.
DTA : DTA boxs, IPTV set tops
TV : Televisions
Replacing Batteries
Before you program or operate the remote control, you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover on the back of your remote control.
STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below.
STEP3 Replace the battery compartment cover.
Operations
Volume Default: DTA volume and mute through the DTA, with the option of controlling volume and mute through the TV. Refer to Section F for programming the volume and mute through your TV.
Button Functions
Programming the Remote Control
Programming the Remote Control
* Quick Set-Up Method*
The Pre-Programmed 3-Digit Code Method**
* The Auto-Search Method
The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component.
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, the DTA LED will light for 20 seconds.If you do not press a button within 20 seconds, the LED light will turn off and exit setup mode and you will need to start over.
A. Quick Set-Up Method
STEP1 Turn on the component you want to program. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5 seconds until the DTA LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table and release both [DEVICE] key and the number key to save the code. The DTA LED will blink twice to confirm that the code is stored.
STEP3 Point the remote control at the component.
STEP4 Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the PreProgrammed 3-Digit code Method or Scanning Method.
Repeat the steps above for all components. (DTA, TV).
B. Quick Set-up Code Tables
DTA
TV
C. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program(TV,DTA).
STEP2 Press the [DEVICE] button (TV or DTA) to be programmed and [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds indicating the unit is ready to be programmed.
STEP3 Point the remote control toward the Component and enter the 3- digit code number assigned to your brand.
*Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off.
STEP4 Once you have found the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was sucessfully stored.
D. Auto-Search Method
STEP1 Turn on the Component you want to program (TV, DTA).
STEP2 Press the [DEVICE] button (TV or DTA) to be programmed and [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds indicating the unit is ready to be programmed.
STEP3 Point the remote toward the Component and press the [CH5] or [CH6] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH5] or [CH6] button as soon as the Component turns Off.
STEP4 Once you have found the correct code, save it by pressing the same [DEVICE] button one more time. The DTA LED light will blink twice to confirm that the code was successfully stored.
Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre Programmed Method.
E. Finding a Component Button’s Setup Code Number
If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference.
STEP1 Press the [DEVICE] button (TV or DTA) you want to verify and the [SEL] button simultaneously for 3 seconds. The DTA LED light will turn on for 20 seconds.
STEP2 Press the [INFO] button and count the number of times the DTA LED light blinks. This number indicates the first digit of the code, followed by the second third, each separated by a one second pause when the LED will turn off.
*Note : 10 blinks represents the number zero.
Example : One blink, (pause), eight blinks, (pause) and three blinks,
indicates code number 183.
F. Programming Volume Control
By default, the VOL+, VOL- and MUTE keys operate through your DTA. If you would like those keys to operate those functions on a TV device, follow these steps.
STEP1 Press the [SEL] button and [DTA] button simultaneously for 3
seconds.
The DTA LED will turn on for 20 seconds.
The next step must be perfomed while the LED is on.
STEP2 Press the [VOL+] button.
The DTA LED will blink.
STEP3 Press the [TV] button that you would like the vollume and mute
buttons to control.
The DTA LED will blink twice to confirm the programming.
*Note : If you wish to have the volume and mute keys operate your DTA Box, press the [DTA] device button in Step 3.
G. Memory Lock System
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
H. Write your TV Set-up codes
Set-up Code Number :
For additional information about your
remote control, go to
www.universalremote.com
Set-up Code Tables
DTA
DTA
TV
TV
TV
TV
TV
TV
References
- Global HR Solutions & Employment Tools for Distributed Teams | Remote
- URC Automation | Think Beyond Everyday
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>