URC-Automation OCE-0189B DTA Digital Adapter Remote Control Owner’s Manual

URC-Automation OCE-0189B DTA Digital Adapter Remote Control

Welcome

The Digital Adapter Remote controls your digital adapter (DTAJ and the Volume, Mute, Power, and Input on many connected TVs.

Identifying the Digital Adapter in Your Home

This remote control is pre-programmed for the DTA 170HD and the DTA 271HD digital adapter models. Follow the instructions below if you want to use the remote to control the other adapter models, your TV, or for advanced programming features. If you are unsure of your DTA model, check the front panel or bottom label of the DTA for one of the following types:

• Cisco/Technicolor DTA 271HD
• Cisco DTA 170HD
• Technicolor DCl401TWC2
• Arris/Motorola HD-uDTA
• Pace DC60Xu HD

This remote only works with the models listed above.

Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

1. Remove the battery compartment cover on the back of your remote control
2. Check battery polarity carefully, and install the batteries as shown in the illustration to the right.
3. Replace the battery compartment cover.

Get to know your Remote Control

Program the Remote to Control Your Digital Adapter

Cisco/Technicolor DTA 271HD

• No additional programming steps are required. Insert the batteries into your remote and it will work immediately with the DTA 271HD.

Want to place your DTA 271HD out of sight?

If you would like to keep your adapter out of sight and still get a remote signal, enable RF mode. Follow these steps, making sure that your DTA front panel is viewable by the remote control:

1. Step1: Make sure that the DTA and TV are connected and powered on.
2. Step2: Point the remote at the DTA front panel.
3. Step3: Press and hold the PROG button for five seconds, until the RED Power button lights up.
4. Step4: Press and release the INFO button.
5. Steps: The RED Power button will blink slowly indicating the remote is ready to be programmed.
6. Step6: A message on the TV screen will prompt you to enter three (3) digits on the remote control.

If the three (3) digits entered are correct, a message on the TV screen will indicate successful programming. If the three (3) digits entered are incorrect, a message on the TV screen will indicate programming did not succeed.

Cisco DTA 170HD

• No additional programming steps are required. Insert the batteries into your remote and it will work immediately with the DTA 170HD.

Technicolor DCl401TWC2

• The steps below MUST be performed If your digital adapter is a Technicolor DCl401TWC2.

1. Step1:  Insert batteries into the remote.
2. Step2: Press and hold the PROG button for five seconds, until the RED Power button lights up.
3. Step3: Press [11, [01, [31 on the remote control keypad.

If the digital adapter code is valid, the RED Power button will blink twice and turn off. After successfully completing steps 1-3 continue following the steps below, making sure that your DTA front panel is viewable by the remote control.

1. Step4: Make sure that the DTA and TV are connected and powered on.
2. Steps: Point the remote at the DTA front panel.
3. Step6: Press and hold the PROG button for five seconds, until the RED Power button lights up.
4. Step7: Press and release the INFO button.
5. Step8: The RED Power button will blink slowly indicating the remote is ready to be programmed.
6. Step9: A message on the TV screen will prompt you to enter three (3) digits on the remote control.

If the three (3) digits entered are correct, a message on the TV screen will indicate successful programming.If the three (3) digits entered are incorrect. a message on the TV screen will indicate programming did not succeed. Your remote is now programmed to work with your DTA. The DTA can be placed out of sight and your remote will continue to control its behavior.

Arris/Motorola HD-uDTA
The steps below MUST be performed If your digital adapter Is an Allis/Motorola HD-up.

1. Step1:  Insert batteries into the remote.
2. Step2: Press and hold the PROG button for five seconds, until the RED Power button lights up.
3. Step3:  Press [11. [OJ, [21 on the remote control keypad.

If the digital adapter code is valid, the RED Power button will blink twice and turn off. Your remote is now programmed to work with your DTA.

Want to place your Arris/Motorola HD-uDTA out of sight?

If you would like to keep your DTA out of sight and still get a remote signal, enable RF mode. Follow these steps, making sure that your DTA front panel is viewable by the remote control:

1. Step1: Make sure that the DTA and TV are connected and powered on.
2. Step2: Point remote at the DTA front panel.
3. Step3: Press and hold the PROG button for five seconds, until the RED Power button lights up.
4. Step4: Press and release the INFO button.
5. Steps5: The RED Power button will blink slowly indicating the remote is ready to be programmed.
6. Step6: A message on the TV screen will prompt you to enter three Ol digits on the remote control.

If the three (3) digits entered are correct a message on the TV screen will indicate successful programming. If the three (3) digits entered are incorrect, a message on the TV screen will indicate programming did not succeed.

Pace DC60Xu HD

The steps below MUST be performed if your digital adapter is a Pace DC60Xu HD.

1. Step 1: Insert batteries into the remote.
2. Step 2: Press and hold the PROG button for five seconds, until the RED Power button lights up.
3. Step 3:  Press 11], [OJ, [41 on the remote control key pad.

If the digital adapter code is valid, the RED Power button will blink twice and turn off,

Want to place your Pace DC60Xu HD out of sight?

If you would like to keep your DTA out of sight and still get a remote signal, enable RF mode.

Follow these steps, making sure that your DTA front panel is viewable by the remote control:

1. Step1. Make sure that the DTA and TV are connected and powered on.
2. Step2. Point remote at the DTA front panel.
3. Step3. Press and hold the PROG button for five seconds, until the RED Power button lights up.
4. Step4. Press and release the INFO button.
5. Step5. The RED Power button will blink slowly indicating the remote is ready to be programmed.
6. Step6. A message on the TV screen will prompt you to enter three (3) digits on the remote control.

If the three (3) digits entered are correct a message on the TV screen will indicate successful programming.  If the three (3) digits entered are incorrect, amessage on the TV screen will indicate the programming did not succeed.

Program the Remote to Control Your TV optional

If you would like to program your remote to control your TV power, input and volume, there are three methods:

• Quick Set-Up Method
• Manual Code Search
• Automatic Code Search

The Quick Set-Up Method enables the easiest set-up by using one-digit codes for up to 20 major brands. Manual code entry requires you to findyour TV brand in the included list of three-digit TV set-up codes. Automatic mode can take up to 15 minutes and requires you to press a button when your TV responds to the remote control.

Quick Set-Up Method

1. Step1. Make sure that the DT A and TV are connected and powered on.
2. Step2. Locate your TV brand in the Quick Set-UpCode Table and identify the corresponding “Button Press· and “Button Number” values.
3. Step3. Press and hold simultaneously for 3 seconds both the TV & MENU or TV & GUIDE buttons, as specified by the ‘Button Press’ value your TV brand is assigned to. The RED power button light will turn on for 20  seconds confirming that you are in theprogramming mode.
4. Step4. While the RED Power button light is on, point the remote at the TV and press the “Button Number” assigned to your TV brand (e.g. for Sharp TV, key 5). The TV should turn off if it does not. press the same number key repeatedly until the TV turns off.

Note: The remote will exit the programming mode automatically if It does not have matching codes and the RfD Power button light will turn off.

1. Steps5.  Once the TV has turned off, press the TV key once again to save the code. The remote is now ready to control your TV. If the matching code could not be found in step 4, use the Manual Code search or the Automatic Code Search method.

Quick Set-Up Code Tables

TV

Manual Code Search

1. Slep1. Make sure that the DTA and TV are connected and powered on.
2. Step2. Locate your TV brand in the list of TV codes included in this instruction sheet
3. Step3. Point the remote at the TV.
4. Step4. Press and hold the PROG button for five seconds, until the RED Power button lights up.
5. Steps5. Release the PROG button and make sure the RED Power button light stays on.
6. Step6. Press and release TV button. The RED Power button will blink once and remain on.
7. Step7. Find the three (3) digit TV code for your TV brand. Press the three (3) number buttons in order on the remote.

If the device code is valid, the RED Power button will blink twice and turn off. The device code will be retained. If the device code is invalid, the RED Power button will blink twice, but stay on. Input another three 0) digit code or cancel the process by pressing the ‘TV” button.

1. Step8. 11 you are able to control TV power on/off and TV volume with the TV and VOL buttons on the remote you havesuccessfully programmed your remote to your TV. If not. return to step 2 and try the next code for your TV brand.

While in programming mode, if a button is not pressed within 20 seconds, the remote will exit the process.

Automatic Code Search

If the code for your TV cant be found using the Manual Code Search, please try the Automatic Code search using the following steps:

1. Step1. Make sure that the DTA and TV are connected and powered on.
2. Step2. Point the remote at the TV.
3. Step3. Press and hold the PROG button for five seconds, until the RED Power button lights up.
4. Step4. Release the PROG button and make sure the RED Power button light stays on.
5. Step5. Press and release the CH UP button to begin auto search mode. The remote will transmit the TV power code every 15 seconds and the RED Power button will blink at the same time. Finding the correct code may take up to 15 minutes.
6. Step6. When your TV turns off, immediately press the TV button. This will stare the code and exit the search mode.
7. Step7. If you are able to control TV power on/off and TV volume with the TV and VOL buttons on the remote you have successfully programmed your remote to your TV. If your remote is still not programmed, you may need to repeat steps 2·6 and press the TV button faster.

Advanced Programming Features **

**

Restore Remote Default Settings

If you want to restore all remote settings to their original state, follow these steps:

1. Step1. Press and hold the PRCXi button for flve seconds, until the RED Power button lights up.
2. Step2. Press [9], [8], [7), waiting for the RED Power button to blink once after each button press. Once all button presses are completed the RED Power button will blink two times quickly to show the procedure is successful.

Controlling Volume

By default, the remote is set to control the DT A volume. If you would like to control the TV volume using your remote, please complete the “Program the Remote to Control Your TV’ steps.

After TV programming, If you would like to control the DTA volume using your remote control, follow these steps:

1. Step1. Press and hold the PROG button for five seconds, until the RED power button lights up.
2. Step2. Press the VOL· button.

After TV Programming, If you would like to control the TV volume using your remote control, follow these steps:

1. Step1. Set the base volume of the DTA to a high level by holding the VOL+ key until the onscreen indicator shows a high or maximum setting.
2. Step2. Press and hold the PROG button for five seconds, until the RED Power button lights up.
3. Step3. Press and release the VOL+ button.

Troubleshooting

If the remote control doesn’t work

Make sure the batteries are inserted correctly. Make sure the TV and DTA are connected and powered on. If the above steps don’t fix the problem, complete ‘Restore Remote Default Settings’ steps and repeat programming.

If the TV Model Is not Included In the TV code list or TV programming is unsuccessful

• Use your TV remote to power the TV on/off.

If audio is low or of poor quality

If you have not programmed your DTA remote to control your TV volume, use your TV remote to increase the base volume level. You should now be able to use your DTA remote to adjust volume as needed. If you have programmed your DTA remote to control your TV volume, the base volume level of the DTA may be set too low. Reset the remote to control the DTA volume by following the steps in the ‘Controlling Volume· section. Turn up the volume of the DTA to high or maximum and then follow the steps to control the TV volume in the ‘Controlling Volume· section.

If the remote control RED power button blinks 5 times when pressed

• The batteries are low. Replace with new batteries.

Federal Communication Commission (FCO Radiation Exposure statement

This remote device is approved as a hand-held and hand-operated only portable (relative to hand) device which is normally operated at 5 cm from a person’s body.

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Warning: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Note: TIie lllillUfictwer Is not responsible for any Radio or 1V Interference caused by unauthorized modifications to this equipment. Such modifications could void the user’.s authority to operate the equipment.

Set-up Code Tables

DTA

TV

Documents / Resources

| URC- Automation OCE-0189B DTA Digital Adapter Remote Control [pdf] Owner's Manual
OCE-0189B, DTA Digital Adapter Remote Control, OCE-0189B DTA Digital Adapter Remote Control, Digital Adapter Remote Control, Adapter Remote Control, Remote Control
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>