Universal Remote UR2-DTA Manual and Codes

: June 2, 2024
: URC

Table of Contents

1. Introduction
2. Replacing Batteries
3. Operations
4. Button Functions
5. Programming the Remote Control
A. Quick Set-Up Method
B. Quick Set-up Code Tables
C. Pre-Programmed 3-Digit Code Method
D. Auto-Search Method
E. Finding a Component Button’s Setup Code Number
F. Programming Volume Control
G. Memory Lock System
H. Write your TV Set-up codes
Read User Manual Online (PDF format)
Download This Manual (PDF format)

USER MANUAL

Universal Remote UR2-DTA

Universal Remote UR2-DTA

1. Introduction

The UR2-DTA is designed to operate the S/A, Pace Micro, Motorola and IPTV set tops, plus the majority of TV equipment on the market as shown below. DTA : DTA boxs, IPTV set tops TV : Televisions

2. Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

STEP-1: Remove the battery compartment cover on the back of your remote control.

STEP-2: Check battery polarity carefully, and install the batteries as shown in the illustration below.

STEP-3: Replace the battery compartment cover.

Replacing Batteries

3. Operations

Volume Default: TV volume and mute through The TV, with the option of controlling volume and mute through the Cable. Refer to Section F For programming the volume and mute through your Cable.

4. Button Functions

5. Programming the Remote Control

There are three ways you can program your remote:
* Quick Set-Up Method*
The Pre-Programmed 3-Digit Code Method**
* The Auto-Search Method

The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using one-digit codes for up to 10 major brands for each component. The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code numbers that correspond to a particular Component’s manufacturer/ brand, so it’s the fastest and easiest of the two methods. (Code Tablesare on the backside of this Instruction Sheet.) The Auto- Search Method scans through all the codes in the remote control, one at a time.

IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, a component LED will light for 20 seconds. If you do not press a button within 20 seconds, the LED light will turn off and exit setup mode and you will need to start over.

A. Quick Set-Up Method

STEP-1 : Turn on the component you want to program. To program your TV, turn on the TV.

STEP-2: Press and hold the [DEVICE] key for 5 seconds until the POWER LED will blink once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Set-up Code Table and release both [DEVICE] key and the number key to save the code. The POWER LED will blink twice to confirm that the code is stored.

STEP-3: Point the remote control at the component.

STEP-4 : Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre- Programmed 3-Digit code Method or Scanning Method. Repeat the steps above for all components. (DTA, TV).

B. Quick Set-up Code Tables

DTA

DTA

TV

C. Pre-Programmed 3-Digit Code Method

STEP-1: Turn on the Component you want to program(TV, DTA).

STEP-2: Press the [COMPONENT] button (TV or DTA) to be programmed and OK button simultaneously for 3 seconds. The POWER LED light will turn on for 20 seconds indicating the unit is ready to be programmed.

STEP-3: Point the remote control toward the Component and enter the 3- digit code number assigned to your brand.

*Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off.

STEP-4: After you’ve entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now it is time to test the VOLUME and MUTE buttons for the TV to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand until you find the best code.

STEP-5: Once you have found the correct 3-digit code, save it by pressing the same [COMPONENT] button one more time. The POWER LED light will blink twice to confirm that the code was successfully stored.

D. Auto-Search Method

STEP-1: Turn on the Component you want to program (TV, DTA).

STEP-2: Press the [COMPONENT] button (TV or DTA) to be programmed and OK button simultaneously for 3 seconds. The POWER LED light will turn on for 20 seconds indicating the unit is ready to be programmed.

STEP-3: Point the remote toward the Component and press the [CH5] or [CH6] button one step at a time or keep it pressed. The remote will emit a series of ON/OFF commands. Release the [CH5] or [CH6] button as soon as the Component turns Off.

STEP-4: Test functions. (Same as for 3- Digit Code Programming Method – Section C). If any of the functions do not work as they should, repeat from STEP 3 using [CH5] or [CH6] buttons to find the correct code.

STEP-5: Save the code. (Same as for 3-Digit Code Programming Method – Section C).

Now, repeat the Auto-Search Method for those Components you could not program earlier with the Pre- Programmed Method.

E. Finding a Component Button’s Setup Code Number

If you used the Auto-Search Method to program a Component, you may not know what the correct code number is. Here is a way for you to identify the code number, so you can record it for future reference.

STEP-1: Press the [COMPONENT] button (TV or DTA) you want to verify and the OK button simultaneously for 3 seconds. The POWER LED light will turn on for 20 seconds.

STEP-2: Press the [INFO] button and count the number of times the Component LED light blinks. This number indicates the first digit of the code, followed by the second and third, each separated by a one second pause when the LED will turn off.

Note : 10 blinks represents the number zero.

Example : One blink, (pause), eight blinks, (pause) and three blinks, indicates code number 183.

F. Programming Volume Control

Volume and Mute control are factory programmed to automatically transfer to the respective Component mode you select, as follows:

DTA : DTA T V : TV

However, you can program the volume controls (Volume Up, Volume Down and Mute) from one Component to operate in another Component. If you wish to store the TV volume control in DTA mode, use the following steps.

STEP-1: Press the [DTA] button and the [OK] button simultaneously for 3 seconds. The [DTA] Component LED will turn on for 20 seconds.

STEP-2: Press the [VOL 5] button.

STEP-3: Press the [TV] button. The Component LED will blink twice to confirm the programming.

To return to original state:
If you wish to restore the DTA volume control in DTA mode, repeat the above steps but press [DTA] in STEP-3.