REXING MTC1 Motorcycle Dash Camera User Manual

MTC1 Motorcycle Dash Camera
User Manual

Overview

Thank you for choosing REXING!
We hope you love your new products as much as we do. If you need assistance or have any suggestions to improve it, please contact us
care@rexingusa.com
877-740-8004
Our support team will respond to you as soon as possible Always a surprise in Reying
Check us out here.
https://www.faebook.com/rexingusa/
https://www.instagram.com/rexingdashcan/
https://www.rexingusa.com/support/registration/

https://www.facebook.com/rexingusa/
https://www.instagram.com/rexingdashcam/
https://www.rexingusa.com/support/registration/
https://www.rexingusa.com/support/

What’s in the box?

Installation

Various Motorcycles models require different installation instructions. For your and your bike’s own safety, please consider consulting a local professional for installation.

Warning
This is for reference only, please adjust the installation method based on your own motorcycle model.
If you would like to purchase other accessories (Camera Extending Cable, Extra parts), please feel free to contact us.
After you confirm the correct quantity and code of terminals, please make sure your cables and terminals are connected completely.
Moreover, if a terminal is broken, it will have a poor connection, therefore it will not work properly. 

Front and Rear Cameras Installation
Note:
Please repeat the same installation steps for both the front and rear cameras.
Warning
Different motorcycles can have different positioning points for your lenses. In some cases, you can stick your lenses upsidedown. If this is the case, you need to adjust the recording angle.

1. Unscrew the lens support fix.
2. Turn the cylinder-shaped lens body 360 degrees.
3. You can adjust lens vertical angle up to 270 degrees.
   • Lenses are Water Proof (IP67)
   • If cleaning is necessary, please use a gentle cloth to clean lenses
   • Please clean any water, oil stain, or dust before sticking your 3M Adhesive Pad. If you relocate your lenses repeatedly, the 3M Glue’s ability to stick will weaken, and your lens may fall.
   • When you accelerate, the image quality may not be very stable, this is the character of CMOS sensors. Please be aware, that this is not part of the agreement.

Monitor Installation

Place your motorcycle’s handle in the middle of the ring, then use a screwdriver to tide the ring

Install a Micro SD Card

• Please use an 8GB to 128GB micro SD card.
• Please use “Class 10 UHS-1” or a higher standard card and higher speed card. If you use class 10 or lower standard cards, the camera may not able to film.
• Please format your micro SD card before use.

Note:

1. The format will delete all contents in your SD card, please back up your files before formatting.
2. Do not release your finger before removing the memory card.
3. Format regularly. We recommend once a month.
4. If you are removing or inserting a micro SD card while power on, it may damage your data or your camera.

Micro SD card installation

Make sure your camera’s power is off, and make sure you insert card correctly, push the card into the card slot until you hear a click

Micro SD card removal

Make sure your camera’s power is off, push the card in the card slot until you hear a click, then you are safe to remove your micro SD card.

Cable Connection
Before installing your camera to your motorcycle, you can connect the camera to the power source through a USB power cable. You can connect the USB power cable to a 5V/2.0A  output or a portable battery’s AC adaptor.

Hardwire Kit Connection

Hardwire Kit

Optional Connection Methods

USB terminal can be connected to an AC adaptor/a portable battery.

Warning

• AC adaptor and portable battery require 5V/2.0A output. If the portable battery is in low power, it will start normally.
• When you connect your camera to the USB power cable, if there is no sufficient electric current, the GPS receiver will be not able to work.
  Even though sometimes these problems occur, they are not faulty.

Product Overview

Basic Operations

1. Power/Screen On/Off
   • Hold for about 3 secs to switch ON/OFF camera.
   • Press the button to deactivate/activate the camera screen.

2. Menu/Up Button
   • Recording Mode: Press to turn ON/OFF microphone (to record). When not filming (press the OK button to stop recording), hold for about 3 secs to enter the setting menu for filming, and hold for about 3 secs again to exit the setting.
   • Play mode: Press and move to a specific location.
   When play stops, hold for about 3 secs to enter the setting menu for play, and hold for about 3 secs to exit the settings.

3. MicroSD card slot
   Compatible from 8GB to 128 GB, we recommend class 7 0 or higher SD card.

4. OK button
   • Filming mode: press, start/stop filming.
   • Setting menu: confirmation and setting location
   • Playing mode: Start/stop playing videos.

5. Mode switch/Screen display switch/Next button
   When voice recording stops: hold for about 3 secs to switch from voices/ videos/photos play mode.
   Filming mode:
   • Press to switch front and rear screen display mode.
   • Hold for about 3 secs, the camera will start SOS filming, and it will lock the video.
   To unlock, hold for about 3 secs

6. Front Camera Port

7. Rear Camera Port

8. Remote control cable

9. Power connection port

10. Powered by Smart hardwire kit

11. Powered By USB cable

12. Monitor mount socket
    Install the dash cam monitor and fix it with the quick-release plate

13. Emergency Video
    Press: switch front and rear lenses display mode.
    Hold for about 3 secs to start Emergency Video, after entering the Emergency Video Mode, hold for another 3 secs to cancel the mode. Emergency Video Mode automatically locks the recorded footage.

14. Remote control RESET button Use a pin to restart the camera.

15. Monitor the RESET button Use a pin to restart the camera

16. LED light display
    Filming: red light on, flashing blue light

17. 3″ LCD Screen
    Not a touch screen.

18. GPS Logger Port

Wi-Fi Connect

To connect to your mobile phone or tablet. Download the APP via link https://www.rexingusa.com/support/rexing-apps/ or scan the QR code below

https://www.rexingusa.com/support/rexing-apps/

SSID: NPD_CarDV_WIFLXXOX PASSWORD: 1234567890

Screen Display While Filming

Note 1
GPS reception
GPS reception received

Note2
Emergency Filming Icon
The icon will be only shown when the video is locked.
Hold the remote control button for 3 secs OR Press the Mode button, to lock the current video.

Menu Setting

Under the video filming mode, press▲ for about 3 secs to open the menu setting page, so you can change the settings

1. Video resolution: FHD/HD

2. Loop Recording: 1/2/3/5/10 minutes *1-minute cycle is recommended

3. Mic: ON/OFF

4. Volume: Standard/Low

5. Beep: ON/OFF

6. Start-up/Shutdown voice: ON/OFF

7. Time setting: set your dash cam’s date and hour

8. Date Format: set your date and hour display format

9. Stamp Format: Date and hour+ model type/Date/model type/OFF

10. Language: ENGLISH/ [# # /#&# /EH tit

11. Flicker: automatic/50Hz/60Hz

12. LCD Power Saver: OFF/1 min/3mins

13. G-Sensor: OFF/High/Middle/Low

14. GPS: ON/OFF

15. Time zone: setting the time zone

16. System setting: charging system

17.  Format SD card: YES/NO

18. Hardware version: show the current version
    Warning
    If the dash cam detects an error, (for example lens terminal connection cable disappears, microSD card lost, insufficient storage or disconnected), a warning notice will be displayed on the screen with a warning voice. Eliminate the notice and voice by pressing any button on the monitor.

19. Loop Recording: With different settings, videos can be stored as 1/2/3/5/10 minute intervals. When the memory card is full, the newest video will overwrite the oldest.

20. Emergency Video/Anti-Overwrite: When filming, hold () for about 3 secs, or the G sensor detects shocks, Emergency Video begins. When Emergency Video is on, an icon will show up on the top of the screen.
    Under the Emergency Video mode, data will be stored in Emergency Video Folder.
    These videos cannot be deleted through the dash cam, if you want to delete them, you have to delete them from the computer.

When G sensor detects shocks while the camera is filming graph 2, graph 2 and graph 3 will be stored in the Emergency Video Folder.

• When the number of emergency video increase, your Micro SD card will be full, so please format your SD card regularly.
• To prevent insufficient space in your memory card, please set the cycling time to 1 minute.

Filming Time

Filming Time Reference
Filming time may vary depending on different Micro SD cards.

Data above for reference only, actual times may be different.
Filming time is the sum of normal filming and Emergency Video Filming. The actual filming time may vary, depending on your user behaviors.

Troubleshooting

If you have any problems while using our product, please refer to the following table

Make sure you are using factory power cable
Crash| Reset the unit
Unable to read SD card| Insert SD card properly
Format SD card with your computer
Replace with a new SD card
Unable to film| Make sure you installed all lenses correctly
Make sure you have sufficient storage in your SD card
Try switching front and rear lenses
Lenes not displaying| Make sure you connected all lenses correctly
Make sure lenses cable are connected
Try switching front and rear lenses
Normal filming not working| Check your SD card storage
Try to change the filming mode
Warning voice, cannot film| Make sure you installed your SD card correctly
Check your SD card storage
Make sure all lenses are installed correctly

Specification

• Wide angle:140°
• 1920×1080
Rear camera| • 2 million-pixel CMOS sensor
• Wide angle:140°
• 1920×1080
Video length| 1/2/3/5/10 minutes
Front and rear camera display| Up+down (Windows)/Down+Up (Mini Windows)/Up
(Right)+Down (Left)/Down(Left)+Up(Right)
GPS| Support
G-Sensor| Support
Microphone| Built-in, can be switch ON/OFF
Speaker| 1W/801
Filming method| Normal/SOS/Photo
Document formats| Video: H.264 (.mov)
Photo: JPEG
Play videos| Windows Media Player
Water resistant level| IP67
Operating voltage| 0C12/24V
Operating temperature| 14F+122F

Warranty & Support

Warranty
The Rexing MTC1 Motorcycle Dash Cam comes with a full 12-month warranty. If you register your product on our official site (https://www.rexingusa.com/support/registration), you can extend the warranty to 18 months.
Support
If you have any questions regarding your product, please do not hesitate to contact us at care@rexingusa.com, or call us at 877-740-8004. Queries are typically answered within 12-24 hours.
Your opinion matters
Rexing is firmly committed to always improving our products, services, and user experience. If you have any thoughts on how we can do even better, we welcome your constructive feedback and suggestions.
Connect with us today at care@rexingusa.com 
Thank you for choosing Rexing!

Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions(1)this device may not cause harmful interference, and (2)this device must  a0oopA any interference received, including interference that may cause undesired operation. Changes or modifications not expressly a.pp/0wed by the party responsible  for compliance could void the user’s authority to operate the equipment
NOTE. This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to Part 15 of the FCC Rules. These units are designed to provide reasonable protection aging harmful interference in a residential installation, This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm4 interference to radio indications. However, there is n guarantee that interference will not occur in a particular installation,  If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures

• Reorient or rel0Cate the reeving antenna
• Increase thee8ration between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is oneted
• Consult the dealer or an experienced radio/TV technician for help

NOTE This device and#ts antena(s) us4 not be 0o-located or opsonin conjunction with other antenna or ta. gritter

Exposure Statement
To maintain compliance with FCC’8 RF Exposure guidelines, This equipment should be installed ad operated with minirum distance of 20em the rof adiator your body. This  device and it.s antenna(s) must not be oo-located or operation in conjunction with other ante or tarnsmitter.

MADE IN CHINA

Documents / Resources

| REXING MTC1 Motorcycle Dash Camera [pdf] User Manual
MTC1, Camera, Dash Camera, Motorcycle Dash Camera
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>