LEZYNE Super High Beam STVZO E1000 LED Electric Bike Light User Manual
- June 5, 2024
- Lezyne
Table of Contents
LEZYNE Super High Beam STVZO E1000 LED Electric Bike Light
READ ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new
Lezyne LED light. Traffic laws mandating lighting vary from country to country.
Inform yourself about lighting laws and regulations in the country of use.
Our e-bike lights are powered by the motor of an e-bike and need to be
manually installed. Proper installation may require some disassembly of the
bike and motor (depending on make and model/battery type) and additional
wiring to connect the light to the motor. Please contact the e-bike or motor
manufacturer for installation instructions. Please note: Any disassembly may
void the warranty of your e-bike. It is highly recommended to have a trained
e-bike professional install your lights for you. Below is general information
about electrical connectivity.
SUPER HIGH BEAM STVZO E1000
Technical Data
Output 1000 Lumen
Ampere LB/HB 0.65A / 1.3A
Wattage LB/HB 8W / 16W
Input voltage 10.5-13.5V AC DC (E-bike baery systems)
Illuminant LB/HB 3 LED / 6 LED
Power cable length 130 cm
Motor Compatibility
The SUPER HB STVZO E1000 is designed to work with a wide variety of E-Bike
systems. It is intended as a solution to add a powerful headlight to an E-bike
system. It supports power supplies and
batteries from 10.5-13.5V. It requires a minimum of 8W to function properly
and includes a Handle
Bar Switch to power the light on/off and change modes. Please contact the
bicycle manufacturer or supplier for information on compatibility and
installation.
Warnings
To meet technical standards the light must be safely installed and ensured
that the light position cannot be moved due to unintentional adjustment.
DO NOT LOOK DIRECTLY INTO LIGHT BEAM or shine into eyes of another.
Lezyne LED Lights have a water resistance rating of IPX7 under IEC standard
60529. Submerging the device is not recommended. If moisture does enter the
casing, air out until
completely dry.
DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.
Lezyne USA, Inc. does not accept any liability for injuries or other damages
resulting from the improper use or improper installation of this product in
any circumstance.
Warranty
In U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the
original purchase date to the original owner (proof of purchase required).
Lezyne warranttes cover any manufacturing defects in materials or workmanship.
Issues not covered by warranty include normal wear & tear, improper
installation, a empting to access or modify electronics, damage or failure due
to accident, misuse, abuse and/or neglect.
For all warranty issues worldwide, please contact the retailer that sold the
product.
In the case of an LED not working properly or not working at all do not use
your light anymore. These lights must be replaced immediately.
For any warranty questions contact:
warranty@lezyne.com
Installation
Lezyne recommends that our E-Bike lights be installed by an E-bike professional. Below is general information about wiring and mounting the light to a compatible bike.
Operation
The front light will be controlled via the on board electronics of the E-bike system for non-remote switch models. These lights are only to be mounted on E-Bikes with DC voltage that have their own battery charge indication and control. The e-bike system must be capable of automatically shuting the light off when the onboard battery reaches a critical voltage to avoid deep discharging of the battery.
Mounting
The light must be mounted at a height between 400 and 1200mm from the ground and cannot be blocked by any parts of the bike (re, handlebar, etc.)
More Information
For more information on Lezyne products, visit: www.lezyne.com
Lezyne USA, 645 Tank Farm Rd., Unit F, San Luis Obispo, California 93401 74055-Y16-SUPER HB STVZO-EBIKE-EMANUAL-R0A1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>