Wiliot MNDB1 Dual Band Bridge Instructions

Wiliot MNDB1 Dual Band Bridge

Specifications

• Product: Wiliot Dual-band Bridge
• Model No: MNDB1
• Description: Enables a reliable wireless power network for Wiliot IoT tags
• Features: Low cost, small form factor, easy installation on ceilings and walls

Product Usage Instructions

Deployment Guidelines:

1. Mount the MNDB1 on a wall or ceiling using the supplied screws or the adhesive sticker. Position the bridge to broadcast towards the area where the Wiliot IoT tags are expected to be.
2. Connect the USB cable to the MNDB1 bridge and a power supply or wall outlet.
3. Once connected to power, the Blue LED turns on solid for 30 seconds indicating that the bridge is running and BLE.
4. After about 30 seconds, the bridge starts RF power transmission the red LED remains on, and the blue LED is on and off.

FCC WARNING & IC Caution

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

General description

• The Wiliot dual-band Bridge enables a reliable wireless power network for Wiliot IoT tags.
• The bridge scans for Wiliot’s tags and echoes their data to the nearest Gateway device.
• It is a low-cost & small form-factor device and can be easily installed on both ceilings and walls using the supplied screws or adhesive sticker.

Box Content

1. MNDB1 Bridge
2. Adhesive sticker
3. USBc cable
4. Screws

Deployment Guidelines

1. Mount the MNDB1 on a wall or ceiling using the supplied screws or the adhesive sticker -Position the bridge to broadcast towards the area where the Wiliot IoT tags are expected to be.
2. Connect the USB cable to the MNDB1 bridge and a power supply/wall outlet.
3. Once connected to power, the Blue LED turns on solid for 30 seconds indicating that the bridge is running and BLE.
4. After about 30, the bridge starts RF power transmission – the red LED remains on, and the blue LED is on and off.

FCC

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body: Use only the supplied antenna.

IC Caution
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body

FAQ

• Q: How do I know if the bridge is functioning correctly?
  • A: The Blue LED will turn on solid for 30 seconds when the bridge is running and BLE. The red LED will remain on when the RF power transmission starts.
• Q: Can I mount the MNDB1 bridge on any surface?
  • A: Yes, you can mount it on walls or ceilings using the supplied screws or adhesive sticker.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>