Carrera 370503032 RC Quadcopter X2 Instruction Manual
- June 5, 2024
- Carrera
Table of Contents
RC
370503032 RC Quadcopter X2
Instruction Manual
Dear customer
Congratulation! You bought a Carrera RC Quadrocopter which has been
manufactured according to today, state-of-the-art technology. As it is our
constant endeavor to develop and improve our product, reserve the right to
make modifications, either of a technical nature or with respect to features,
materials, and design at the arty time, and .out prior notice. For this
reason, no claims will be accepted for any slight deviations in your product
from the data and Illustrations contained in these Instructions These
operating and assembly instructions are an integral part of the product. These
instructions are M be kept for future reference and in the event that the
product is passed on to a third party. For the latest version of these
operating instructions and information on replacement and spare parts
available, please visit Carrera-rc, com in the service area.
WARNING! Before you first fly the model, find out whether there is a
legal requirement to ensure model airplanes such as this in your country.
Declaration of conformity
Carrera Toys GmbH hereby declares that this model including the controller
conforms with the fundamental requirements of the following EC directives: EC
Directives 200S/48 and the other relevant regulations of Directive 2014/53/EU
(RED).
The original declaration of conformity can be requested from Carrera-
rc.com.
Maximum radio-frequency power transmitted <10 dBm • Frequency range: 2400-2.5
MHz
Warning!
WARNING! This toy contains small parts which can be swallowed and are
therefore not suitable for children under 3 years of age.
WARNING! The danger of pinching during operation! Remove all packaging
materials and wire fastenings before handing the toy over to the child. For
information and to answer any questions, please retain the packaging, address,
and instructions in a safe place for future reference. Keep the Instructions
for use for later reference. Note for adult supervisors: Check if the toy Is
assembled as Instructed. The assembly shall be performed under the supervision
of an adult.
WARNING! Not suitable for children under 12 years old!
This product’s not intended for use by children will. supervision of a parent.
Hying the helicopter requires skill and children must be trained under the
direct supervision of an adult. Before first use: Read the user, Information
together with your child. Inappropriate use may result in severe injuries
and/or damage to property. It has to be operated w the care and caution and
requires both mechanical and mental skiing. The operating instructions contain
notes on safety and technical regulations as wet as information on maintaining
and operating the product. It is indispensable to read these instructions
thoroughly before the first usage. Only these herbs avoid accidents with
injuries and damage. Hands, hair and loose clothing, and.r, and other objects
such as pens and screwdrivers must be kept away from the propeller (rotor). Do
not touch the rotating .r. ally take care that your hands DO NOT get close le
the rot, blades
WARNING: Do not fly near your face to avoid Injuries. For use only
outdoors —not to be used Indoors. Risk of eye injuries. Start and fly only
when the area is appropriate for the intended use (free area, no obstacles)
and only within direct visual contact. As a user of this product, you are
solely responsible for handling it safely in order to ensure that neither you
nor other persons or their property suffer damages or are endangered.
- Never use your model with weak remote control batteries.
- Avoid by areas. Arrays make sure that there is enough space.
- Preferably do not use your model on an open street or in public areas in order not to .anger or hurt anyone.
- CAUTION: Do not start up and fly when persons, animals, or any obstructions are within the flying range of the Ouadrocopter.
- Start and fly is strictly forbidden near high voltage poles, railway tracks, roads, swimming pools, or open water.
- Only operate under good visibility and can weather conditions.
- Exactly observe the instructions and warnings for this product and for any possible additional equipment (battery charger, rechargeable batteries, etc.) being used by you.
- Should the Ouadrocopter come into contact with any living thing or solid object, immediately return the gas control to zero, in other words, the left-hand Mystic. must be at the stop at the bottom of the slide!
- Avoid any moisture as this might do damage to the electronics.
- There is a risk to suffer severe injury or even death if you put parts of your model into your mouth or lick them.
- Do not change or modify anything on the Ouadmoopter.
If you do not agree to these terms please immediately return the complete
OuadrocoMer model in new and unused condition to the retailer.
Important Information concerning Lithium Polymer rechargeable batteries
Lithium-Polymer (LiPM rechargeable batteries are signilicantk more sensitive
than traditional aka’. or NiMH-rechargeable batteries nom., used with radio
control units. There. the instructions and warnings have to be observed in
detail In case of improper use of LiPo rechargeable batteries, there is a
danger of fire. Always follow the manufacturers’ instructions if you dispose
of LiPo rechargeable batteries.
Regulations on disposal of waste electrical and electronic equipment
(WEEE)
This symbol, showing a refuse bin with a cross through them, denotes empty
batteries, and recharge. batteries, button., rechargeable battery pa.
equipment batteries, (bused electrical equipment, etc. should not be damsed of
in domestic refuse, as they are harmful to the environment and health. Please
hap to preserve environment and health and tale to your children about the
correct disposal of used batteries and doused electrical equipment. Batteries
and disused electrical equipment should be handed into
the usual collection points where they can be properly recycled. Do not mix
dissimilar battery types or employ new and used batteries together. Empty
batteries should be removed from the product. Do not recharge non-rechargeable
batteries due to the risk of explosion. Batteries are to be inserted with the
correct polarity.
WARNING, Rechargeable batteries are only to be charged by adults.
Exhausted batteries are to be removed from the toy. Rechargeable batteries
should be removed from the product before charging. Supply terminals are not
to be shod-circuited. Only use the batteries recommended or equivalent types.
WARNING: For the purposes of recharging the battery, only use the
detachable supply unit provided with this toy. Battery chargers used with the
toy are to be regularly examined for damage to the cord, plug, enclosure, and
other parts, and in the event of such damage, they must not be used until the
damage has been repaired. The toy is only to be connected to Class II
equipment bearing the following symbol.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This product has been tested and found to comply with the limits
for Class B digital devices, pursuant to Part 15 of the FCC Rules. These hits
are designed to provide reasonable protection against harmful interference in
a residential installation. This product generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If the product does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to t, to correct the interference by one or more of
the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the product and receiver.
- Connect the product into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC statement
The device contains license-exempt transmitter(s)/ receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- The device must not cause interference;
- The device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-3 (B)/NME1-3(B)
Guidelines and warnings for the use of LiPo rechargeable batteries
- You have to charge the attached 3.7 V 380 mAh/1,41 Wh LiPo rechargeable battery in a safe place and at a safe distance to flammable material. • Never leave the battery unattended while it is charging
- After a flight, the rechargeable battery has to cool down to the ambient air temperature before charging it.
- You must always use the corresponding LiPo charging unit (USB cable / remote control). In case of non-compliance with these directions, there is a danger of fire resulting in health risks and/or damage to property. NEVER use any other battery charger.
- Should the rechargeable battery swell or deform while discharging or recharging, you have to immediately stop charging or discharging the battery. Take the battery out as quickly and carefully as possible and place it in a safe and open area offside any inflammable material and watch it for at least 15 minutes. In case you continue charging or discharging a battery that has already started to swell or deform there is a danger of fire! Even in case of slight deforming or ballooning the rechargeable battery has to be taken out of operation.
- Store the rechargeable battery at ambient temperature in a dry place.
- Always recharge the battery after use to prevent its from becoming deep discharged. After use, the battery must be allowed to cool down for at least 20 minutes before it can be fully recharged. Recharge the battery occasionally (suggested every 2-3 months). Supply terminals are not to be short-circuited. Failure to treat the battery as described above can lead to its becoming defective. Never leave the battery unattended while it is being charged.
- When transporting or temporarily storing the rechargeable battery the temperature should be between 5-50°C. If possible, do not store the battery or the model in a car and do not expose it to direct sunlight. In case the battery is broiled it can be damaged or catch fire.
Note: If the battery voltage/output is low you will recognize that a considerable trim and/or control is necessary to avoid the Quadrocopter starting trundling. This usually occurs before reaching a battery voltage of 3 V and it is a good moment to end the flight.
Contents of package
1x Quadrocopter
1x Controller
1x USB charging cable
1x Rechargeable Battery
2x 1.5 V Mignon AA batteries (non-rechargeable)
Recharging the LiPo rechargeable battery
Rechargeable batteries are to be removed from the toy before being charged.
Make sure you only charge the LiPo rechargeable battery supplied with the LiPo
charging unit also supplied (USB cable and remote control). If you try to
charge the rechargeable battery with a different LiPo battery charger or any
other battery charger, this might cause serious damage. Please carefully read
the previous chapter with warnings and guidelines on the usage of rechargeable
batteries before proceeding. Supply terminals are not to be short-circuited.
You can charge the rechargeable battery fitted in the Quadrocopter with its
USB charging cable from a USB port on a computer:
2a Charging via computer:
- Rechargeable batteries are to be removed from the model before being charged.
- Connect the USB charging cable with the USB port of a computer. The LED on the USB charger cable lights green indicating that the charger unit is correctly connected to the computer. If you plug in a Quadrocopter with a discharged battery, the LED on the USB charging cable no longer lights up, showing that the Quadrocopter battery is being charged. The USB charging cable and the charging socket on the Quadrocopter are designed to make incorrect connection impossible.
- It takes about 60 minutes to recharge a discharged battery (but NOT a deep-discharged one). When the battery is fully charged, the LED display on the USB charger cable lights up green again.
Note: when supplied, the lipo-battery is already partially charged. So
the first charging cycle may well take less time.
It is essential to follow the connection sequence given above! Undo the
plugged connection on the Quadrocopter when you are not using the
Quadrocopter. Failure to observe this precaution may cause battery damage!
2b Insertion of the rechargeable batteries into the Quadrocopter
- Open the cover of the battery compartment with the aid of the enclosed screwdriver. Insert the battery. Close the battery compartment.
- If the LED on the Quadrocopter flashes slowly. you must change the battery.
Inserting the batteries in the remote control
Open the battery compartment with a screwdriver and insert the batteries in
the remote control. Please keep in mind the correct polarity. Different types
of batteries or new and used batteries are not to be mixed. After having
closed the compartment you can check all functions of the remote control with
the help of the power switch on the front. With the power switch turned ON and
functioning correctly, the top center LED on the remote control will light up
red. If the LED control flashes slowly and an acoustic signal is heard, the
batteries in the controller must be changed.
Frequency bind between model and remote control
The Carrera RC Quadrocopter and the controller automatically link up and are
renewed with every operational start-up. If initially there are any problems
with communication between the Carrera RC Quadrocopter and the remote control,
please carry out a new frequency bind.
- Connect the battery in the model.
- The LEDs on the quadrocopter now flash rhythmically.
- Switch on the controller at the power switch.
- WARNING! Immediately after switching it on, place the Quadrocopter on a flat and level surface. The gyro system will then set itself automatically.
- Slide the left joystick, thus the gas lever, completely up and down again into the zero position.
- Allow the helicopter a few moments until the system is correctly initialized and is ready for operation.
- The binding has now been successfully established.
- The LED on the controller now lights continuously.
Description of the Quadrocopter
5 1. Rotor system
2. Rotor protection cage
3. LEDs O4. Battery cable
5. Quadrocopter connecting plug
6. Battery compartment
Range of functions of the remote control
6 1. Power (ON / OFF) 1″‘
2. Control LED
3. Gas Circling
4. Forwards / backwards right / left banking
5. Trimmer for right / left banking
6. Trimmer for forwards / backwards
7. Auto-Start & Fly to .1m Button
8. Auto-Landing Button
9. Looping Button
10. Headless Mode
11. Return aid
12. Beginner/Advanced switch (30D/Q/60%/100%)
3 13. Battery compartment
Choosing the flight area
8 When being prepared for the first flight you should choose a closed
room which is as large as possible without any persons or obstacles. Due to
its size and controllability, experienced pilots may be able to fly the
Quadrocopter in relatively small rooms. For your first flights, we strongly
recommend you choose a room with a minimum floor space of 5 x 5 meters and
2.40 meters in height. After having trimmed your Quadrocopter for flight and
made yourself familiar with the controller and its functions you may start
flying in smaller and less open environments.
To be used in the domestic areas (house and garden) only. There must be
no persons or objects such as pillars between the controller and the
Quadrocopter to obstruct direct connection.
Checklist for flight preparation
This checklist is not a substitute for the contents of the operating instructions. Although it can be used as a quick-start guide, we strongly recommend you first read the operating instructions in detail before you proceed.
- Check the contents of the package.
- Charge the lipo battery as described in the section “Recharging the LiPo rechargeable battery”.
- Fit 2 AA batteries in the controller, making sure their polarity is correct.
- Look for a suitable environment for flying.
- Slide the battery into the battery bay on the bottom of the Quadrocopter. 2b
- Connect the battery in the model.
- Link, as described in 4
- Press button 7 to start the helicopter (Figure 7 ).
- Important note! P ease perform the auto-trimming 17 before each flight without fail!
- Check the control system.
- Make yourself familiar with the control system.
- Trim the Quadrocopter as necessary as described under 17 18 19 20 so that when hovering it no longer moves from the spot without a command from the controller.
- The Quadrocopter is now ready to be flown.
- If the Quadrocopter displays no functions, retry the above binding procedure.
- Fly the model.
- Land the model.
- Disconnect the battery plug connection.
- Always switch off the remote control last.
Flying the 4-channel Quadrocopter
NOTE!
Take care particularly in the first few flights to move the lever on the
controller very gently and not over-hurriedly. Asa rule, only very small
movements of the respective levers are necessary to carry out the desired
control commands!
If you notice that the Quadrocopter moves forwards or to the side without your
touching the respective lever,
please adjust the trim of the Quadrocopter as described in 17 18 19 20
9 +-Gas (up /down)
To fly higher, push the gas lever on the left cautiously forwards. To land or
fly lower, push the gas lever on the left cautiously backward.
10 To make the Quadrocopter circle to the left or the right spot, move
the lever on the left cautiously to the left or the right.
11 To fly the Quadrocopter to the left or the right, push the lever on
the right cautiously to the left or the right. le
12 To fly the Quadrocopter forwards or backward, push the lever on the
right cautiously forwards or backward.
Looping function
WARNING! ONLY FOR EXPERIENCED PILOTS!
13a If you press the “Looping Button”, then an acoustic signal sounds 5x
a time, As long as the acoustic signal sounds, slide the right-hand joystick
up, down, to the right, or to the left. The Quadrocopter then carries out the
loop or rolls in the respective direction. Before you do this, make sure you
have ample room on all sides (about 2.5 m —8′).
Beginner/Advanced switch
WARNING! 100 % IS ONLY FOR EXPERIENCED PILOTS!
13b 30% = beginner mode Signal sounds once on switching over.
60% = medium mode The quadrocopter reacts more sensitively than in the
30 % mode. Signal sounds twice on switching over.
100% = Advanced Modus -> 3D Modus
The Quadrocopter reacts very sensitively to joystick movements. Signal sounds
three times on switching over.
Headless Mode
13c Theheadesszodehelps beginners eamhowtofi Regarlzso
fwthdirec1iontheauadrocopter is rotated, the idea ctioiai ways cores ponds
examine their direonimp, rented the controller. Therefore a beginner longer
has to steer mirror-imaged when he flies e.g. to himself. II you pre. the
“Headless Mode Button” 10 tie, an acoustic signal sounds for as long as
you are in the Headless mode. To deactivate the Headless mode. press the
button renewed.
Automatic control of altitude
14 Tahned Qjouyas dtriocock dteirngwitlhi emafiiin gthatinTthhee
iciguhrrte ,ntaftnydi ogyastitkud ceanaub teomusaeticdat Iolyfalys fsoorwoy
dssfrauc ktradssea thned left-hand at the same height. The left-hand joystick
is used to circle on the spot with a left/right-hand movement.
Auto-Start & Fly to =1 m
15 Press the ‘Auto-start & fly to ‘.1 m’ button on the controller, in
order to start the motors and automatical-ly fly up to the altitude of about 1
m . You are able to influence the direction of flight at any time during the
starting operation by means of moving the right joystick. The Quadrocopter
will maintain itself in position automatically as soon as the altitude of
about 1 m has been reached. The flying height can be changed ma-nually at any
time by moving the left-hand joystick forwards (increase height) or backwards
(reduce height).
Auto Landing
16 You can trigger the automatic landing function at any time by means of
pressing the ‘Auto landing’ but-ton. The speed of the rotors will reduce
gradually as a result. You are able to influence the landing posi-tion at any
time during the landing procedure by means of moving the right-hand joystick.
The motor will switch itself off as soon as the Quadrocopter is on the ground.
Trimming the Quadrocopter
17 Auto-trimming
- Place the Quadrocopter on a horizontal surface.
- Link the Quadrocopter with the controller as described in “Linking the model with the controller”.
- Slide the gas lever and the lever for forwarding/back simultaneously into the right lower corner. The LED on the Quadrocopter flashes on briefly and then lights up continuously. The signaling tone will sound once.
- The neutral setting is completed.
18 When hovering, if the Quadrocopter flies to the left or right without
you moving the lever for left / right movement, please proceed as follows: If
the Quadrocopter moves on its own fast or slow sideways to the left, press the
lower right trimmer for right / left tilt in steps to the right. If the
Quadrocopter moves right, press the trimmer for right / left tilt in steps to
the left.
19 When hovering, if the Quadrocopter flies forwards or backward without
you moving the lever for for-m’ wards or backward movement, please proceed as
follows: If the Quadrocopter moves on its own fast or slow forwards, press the
upper right trimmer for forwards / backward in steps downwards. If the Quadro-
copter moves backward, press the trimmer for forwards / backward in steps
upwards.
Return aid
20 Make sure there are no obstructions in the flight path and that there
is no wind! WARNING: the model is NOT equipped with a GPS system!
As long as this button is pressed, the quadrocopter returns back in the
direction of the pilot, regardless of how it is positioned.
WARNING! Only functions if the quadrocopter is in front of the pilot.
21 Changing the rotor blades
22 OR code for the motor-change system, spare parts, and further
information.
23 WARNING!
Be sure to note the marking and color, also the till angle of the rotor
blades!
Front left: red—marking B
Front right: red—marking “A
Rear right: black—marking “B”
Rear left: black—marking “A”
Carrera toys GmbH.Rennbahn Allee 1.5412 Puch/Salzburg .Austria
|
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>