HuddleCamHD HC-JOY-G4 Serial Joystick Controller User Manual
- June 11, 2024
- HuddleCamHD
Table of Contents
HC-JOY-G4 Serial Joystick Controller
User Manual
HC-JOY-G4 Serial Joystick Controller
Please check huddlecamhd.com for the most up to date version of this document.
Preface
Congratulations on receiving your new HuddleCamHD Serial Joystick Controller.
This manual introduces the function, installation, and operation of the
Joystick. Prior to installation and usage, please read the manual thoroughly.
Precautions
To avoid any damage to the unit, please take these precautions when using your
HC-JOY-G4 Joystick Controller.
- Please read this manual carefully before using the joystick.
• Avoid damage from stress, violent vibration or liquid intrusion during transportation, storage or installation.
• Do not apply excessive voltage. (Use only the specified voltage.) Otherwise, you may experience electrical shock.
• Keep the joystick controller away from strong electromagnetic sources.
• Do not clean the joystick controller with any active chemicals or corrosive detergents.
• Do not disassemble the joystick controller or any of the joystick’s components. If problems arise, please contact your authorized dealer.
• After long term operation, moving components can wear down . Contact your authorized dealer for repair.
Warranty
HuddleCamHD includes a limited parts & labor warranty for all HuddleCamHD
manufactured joystick controllers . The warranty is valid only if HuddleCamHD
receives proper notice of such defects during the warranty period .
HuddleCamHD, at its option, will repair or replace products that prove to be
defective . HuddleCamHD manufacturers its hardware products from parts and
components that are new or equivalent to new in accordance with industry
standard practices .
Supplied Accessories
When you unpack your joystick controler, make sure that all the supplied
accessories are included:
• Joystick Controller | 1 |
---|---|
• RS-232 Cable | 1 |
• 12V DC Power Supply | 1 |
• Quick Start Guide | 1 |
Note: The included RS-232 cable is used to connect the joystick the first
camera. If the first camera is located further than the cable, a DB9 extender
should be used. Subsequent 2nd, 3rd and 4th cameras are connected using the in
and out 8-pin mini-din connections using cascade cables. You can learn more at
PTZOptics.com/cables.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules . These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment . This equipment
generates, uses, and can radiate radiofrequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications . FCC Caution: Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment . Operation is
subject to the following two conditions: This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
• Warning – This is a class B product. In a domestic environment, this
product may cause radio interference in which case the user may be required to
take adequate measures.
Copyright Notice
The entire contents of this manual / guide, whose copyright belongs to
HuddleCamHD, may not be cloned, copied, or translated in any way without the
explicit permission of the company. The product specifications referred to in
this document are for reference only and as such are subject to updating at
any time without prior notice.
Physical Description
1. Speed Control Dial
Adjust Control Speeds
2. Mode Change Button
Basic & Matrix Modes
3. LCD Display
Displays Connection Info
4. Set & Call Presets
Set and/or Call Preset
5. Exposure Control
Exp Modes & Settings
6. White Balance Control
WB Modes & Settings
7. Joystick Controller
Pan, Tilt & Zoom| 8. Focus Control
Adjust or Lock Focus
9. Camera Select
Select your camera
10. Numeric Buttons
Used for Presets
11. Backlight Toggle
Increase Backlight
12. OnePush Trigger
Calculate white level
13. Joystick Setup Menu
Enter Joystick Menu
14. Camera OSD
Adjust camera settings
---|---
Back View of the Joystick Controller
- RS-232 Port (DB9 connection)
- RS-422 Port
- 12V DC Power Port
- Power Switch
- Grounding Knob
Key Product Features
- All Metal housing
- VISCA, PELCO-D and PELCO-P protocol support
- Key-press “BEEP” confirmation (optional – set on or off)
- Variable speed control of pan, tilt, zoom, focus, and presets
- Auto/Manual Focus and Iris
- Cameras #1 -7 Quick Select buttons
- Quick preset set & call (0 – 9)
- Set and Call up to 255 presets per camera
- Real time display of the current status
- 2 Year Warranty
Key Technical Specifications
- Control Interfaces
- RS232 full-duplex, RS485 semi duplex, RS422 full-duplex
- Variable Baud Rate 1200 to 19200 bps
- Maximum communication distance: RS485: 3,937ft [1200m] using 24 gauge twisted pair cabling
- Can control a maximum 255 cameras via Pelco-D/P
- Voltage: 12VDC
- Power Consumption: 6W Max
- Display: LCD
- Working Temperature: 14°F ~ 122°F [-10° ~ +50° C]
- Working Humidity: 10 ~ 90% (non-condensation)
- Weight 3 .4 lbs. [1 .6 kg]
- Dimensions: 12.6”(W) x 7.1”(D) x 4.3”(H) [320mm x 181mm x 110mm]
Installation
-
Power Supply Interface (5.5mm x 12mm center pin JEITA style jack): 12VDC / 2000mA power supply
-
RS485/422 interface (5p screw terminal):
– 1:485+/422TxA
– 2:485-/422TxB
– 3:422RxA
– 4:422RxB
– 5:485/422Gnd -
RS232 interface (DB9M port): 2:Rx, 3:Tx, 5:Gnd
Hardware Features
- Keys: momentary push buttons (keys)
- Joystick: 3-axis joystick
- Digital display: LCD display
Control Mode
-
VISCA, PELCO-P and PELCO-D protocol support
-
Control interfaces:
– 5p Screw Terminal (RS485/RS422)
– DB9 (RS232) -
Baud rate: 1200, 2400, 4800, 9600, 19200
-
Parameters: 8 bits, 1 stop bit, No parity
Keyboard/Joystick Operation
Basic Control
-
Pan & Tilt Control
– Joystick movement provides variable speed pan and tilt of the camera head. -
Zoom Control
– Rotation of the joystick controls variable speed zoom of the lens .
▪ Clockwise rotation of the joystick = zoom in .
▪ Counter-clockwise rotation of the joystick = zoom out .
Manual Control Options
-
Focus Control – VISCA Protocol only. Pelco-D & P do not support Manual Focus commands.
– You can adjust the focus level by twisting the Focus knob . Manual Focus is automatically enabled once the knob is twisted.
▪ Twist the knob clockwise to Focus Far, and counter-clockwise to Focus Near.
– You can return to Auto Focus mode by pressing in the Focus knob. -
Exposure Control – VISCA Protocol only. Pelco-D & P do not support Manual Exposure commands.
– The Iris / Shutter / Gain knob allows you to adjust the corresponding Exposure settings . Press the knob in to change your selection.
– Note: Some cameras do not have an “Iris” or “Shutter” mode . Use Manual Exposure mode for best results. -
White Balance Control – VISCA Protocol only . Pelco-D & P do not support Manual White Balance commands.
– The R Gain / B Gain knob allows you to adjust the corresponding Red or Blue Gain level . Press the knob in to change your selection.
– Note: Your camera must be set to Manual White Balance mode in order to manually define the Red and Blue Gain levels. -
Speed Control
– You can adjust the Pan, Tilt, Zoom, Focus, and Preset control speeds by twisting the Speed knob . Press the knob in to change your selection.
– You can adjust the Pan (0 – 24), Tilt (0 – 20), Zoom (1 – 7), Focus (1 – 7), and Preset Speed (1 – 24).
Selecting a Camera
Quick Camera Select
- Press the CAM # button associated with the camera you want to control .
CAM ID Button
- Press the CAM ID Button
- Input the Camera ID you want to control .
- Press the Enter button
PTZ Presets
Set a PTZ Preset
• Quick Preset Set
- Press and hold one of the 0 – 9 buttons for 3+ seconds to Set a preset in the current position.
Set Button
- Press the Set button
- Input the Preset number you want to Set
- Press the Enter button
Call a PTZ Preset
- Quickly press one of the 0 – 9 buttons to Call that preset .
Call Button
- Press the Call button
- Input the Preset number you want to Call
- Press the Enter buttonave “Call” mode, press the “Esc” key .
Notes on using presets with VISCA:
For your convenience, the HC-JOY-G4 uses the same presets as the IR remote
controller, VISCA, Pelco-D, or Pelco-P protocols. This is in contrast to
Sony’s traditional offset of 1 between the IR remote and VISCA commands.
Joystick Setup Menu – LCD Menu
Key Tone
- Options include: On, Off
Restore Default
- You must press Enter twice to restore the default settings . Press the Escape button to cancel.
ADD:
- Options include: VISCA, Pelco-D, Pelco-P
- To add a camera to the joystick, you will need to select the desired control protocol then press the Enter button . Use the joystick to select the camera ID.
– Left and Right move in increments of 1.
– Up and Down move in increments of 5.
Version
- Displays the firmware version
Invert Pan
- Options include On, Off
Invert Tilt
- Options include On, Off
Keyboard/Joystick Connection Wiring and Indicators
Power:
- Keyboard/Joystick requires external 12VDC . Use only the 12VDC power supply shipped with the unit.
The Keyboard/Joystick may be connected to cameras via RS-232, RS-485 or RS-422.
- For RS-232, connect the DB9 port of the KB to the miniDin8 (VISCA) port of the camera with pin-out as follows:
– KB Tx – Pin 3 ………….. Camera Rx – Pin 5
– KB Rx – Pin 2 ………….. Camera Tx – Pin 3
– KB Gnd – Pin 5 ………….. Camera Gnd – Pin 4
When connecting multiple cameras,the first cable in a serial control chain is a DB9 to 8-pin mini-din cable as seen in Fig. 1 (included). The 2nd, 3rd, and 4th cameras are connected using an 8-pin minidin cascade cable as seen in Fig. 2 (not included). See Fig. 3.
-
For RS-485, connect the 5p screw terminal port of the KB to the RS-485 port of the camera with pin-out as follows:
– KB Ta – Pin 1———- Camera (+)
– KB Tb – Pin 2———- Camera (-)
– KB Gnd – Pin 5———- Camera (G) (if present – some cameras will not require a G) -
For RS-422, connect the 5p screw terminal port of the KB to the RS-422 port of the camera with pin-out as follows:
– KB Ta – Pin 1 …………… Camera (Rx-)
– KB Tb – Pin 2 …………… Camera (Rx+)
– KB Ra – Pin 3 ………….. Camera (Tx-)
– KB Rb – Pin 4 ………….. Camera (Tx+)
– KB Gnd – Pin 5 ………….. Camera (G) (if present – some cameras will not require a G)
Troubleshooting
-
Cannot Control Camera at all
– Check that LCD is in the Main Menu . Press “Esc” key to return to main menu, if needed.
Note: Repeated presses may be required depending on how deep you are in a menu, e.g. this can often happen after setting presets and then attempting to Call presets without exiting the Set menu.
– Check both KB settings and camera settings to ensure that the following ALL match:
▪ Camera ID (e.g. 01, 02, etc…)
▪ Camera Protocol (e.g. VISCA, PELCO-P, PELCO-D)
▪ Baud Rate (e.g. 9600)
– Check all KB-camera connections and cabling per “Connection Wiring and Indicators” section above. -
Controlling more than 1 camera at a time.
▪ Check all cameras to ensure that each has a unique ID .
▪ Check all camera settings in KB menu to make sure that the protocol setting for that camera ID matches that of the actual camera .
– Note, you cannot typically mix VISCA, Pelco-P or Pelco-D cameras in the same daisy chain .
▪ Check control wiring .
– For RS232, cabling must flow from KB into the VISCA-in port of the first camera and then from VISCA-out port of first camera to VISCA-in port of next camera, etc … A VISCA cross-over cable must be used for all camera to camera connections . These are available from HuddleCamHD in various lengths as well as from other sources.
– For RS485 and RS422, all connections are in parallel (e .g . all cams’ 485+ are connected to KB’s 485+ and all cams’ 485- are connected to KB’s 485-) and termination may be required depending upon overall cabling distances involved.
152 Robbins Rd., Downingtown, PA 19335 USA
HuddleCamHD.com
484-593-2247
©2023 HuddleCamHD
All Rights Reserved
References
- Network and USB 4K EPTZ Webcam with Optical Zoom - HuddleCamHD
- PTZOptics: A manufacturer of robotic pan, tilt, zoom camera solutions
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>