CARRERA 629110 Impel Is-2 2.0 Electric Scooter Owner’s Manual

: June 4, 2024
: Carrera

Table of Contents

CARRERA 629110 Impel Is-2 2.0 Electric Scooter
Please Read Before Use
Product Overview
Setting up the safety features
Unpacking and assembling the scooter
User weight limit
charge
Storage
Technical Specifications
Scope of Warranty In case of problems:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CARRERA 629110 Impel Is-2 2.0 Electric Scooter

Please Read Before Use

Before any use, consult the legislation in force in your country.
Always wear a helmet and other appropriate protective equipment.
Ensure your battery is fully charged before driving.
Observe all road markings, signs and traffic regulations. Ensure you are always visible to others.
Watch for pedestrians and other road users.
Your Carrera impel is-1 scooter is not suitable for use in rainy weather: You may slip and severely harm yourself.

Warning:
As with any mechanical component, a vehicle is subject to high stress and wear and tear. Different materials and components may react differently to wear or fatigue. If a component’s life expectancy is exceeded, it may fail suddenly and cause injury to the user. Cracks, scratches and discolouration in high- stress areas indicate that the component has exceeded its life expectancy and should be replaced.

Recommendation: Safe use
Before using your electric scooter, make sure it is in good working order. In particular, check the following:

Nuts, screws, clamping levers, tightening of components
Brakes are in working order
Handlebars are correctly attached to the stem
Wheels are properly tightened and attached to the frame and the fork Tyres are in good condition and are properly inflated
The reflectors are correctly positioned.
Lights are in working order

RECOMMENDATION:
Your electric scooter should be serviced every 6 months by a professional to ensure it is in good working order and safe to use. It is the user’s responsibility to ensure that all components are in good working order before use.

WARNING
Choose a safe place, away from traffic, to familiarise yourself with your new electric scooter. The motor may start in a forceful manner, check that your handlebars are straight and that the path is clear. Getting used to the product requires an adjustment period. To avoid a serious accident during the first few months:Make sure you are in good health before getting on your scooter.In case of unusual weather conditions (rain, snow, etc) proceed with care and adjust your speed and reactions accordingly.The user must comply with the requirements of national regulations when using the electric scooter on public roads (for example, lighting and signalling). Halfords declines all responsibility if the user of the electric scooter does not comply with the regulations in force.

Warning:
You acknowledge that you are responsible for any loss, injury or damage caused by a failure to comply with the above instructions and that this will automatically void the warranty.

Product Overview

About The Carrera impel is-2
The Carrera impel is-2 is a two-wheeled electric scooter.

Package Contents

Carrera impel is-2 Electric Scooter (unassembled handlebars)
Charger
User manual
3mm hex key
4 screws for the stem

Carrera impel is-2 Description

Handlebars
Stem
Deck
Rear disc brake
Hub motor
Kickstand
Front-wheel
Headlight
Front and rear brake levers
Display
Throttle lever
Head unit clip
Folding mechanism
Head unit mount
Taillight
Space for license plate (if required by local regulations/ authorities)
Side reflectors
Control buttons
Bell

Setting up the safety features

Lighting
Lighting is provided on the scooter: it consists of two reflectors (a white one included in the headlight and a red one attached to the rear mudguard), a headlight, a taillight, and four other orange reflectors on the sides.The lighting system is a safety feature of your electric scooter. It must be in good working order. Ensure that your lighting system is working properly before you set off. The front and rear lights are powered by the scooter’s battery.

Bell
A bell is installed on your handlebars. It will allow you to be heard from a distance of 50m. The bell is a safety feature of your scooter, it must be installed on your handlebars.

Helmet use
For safe use, helmet use is strongly recommended. It guarantees a reduction in head trauma in the event of a fall.

Appropriate footwear
For safe use, shoes must be worn at all times. For more information, please consult your place of purchase.

Unpacking and assembling the scooter

Open the box and take out all the parts {do not throw away the packaging, you will need it if you need to return the product).
Lift the stem while holding the handlebars.
Lift the folding lever on the folding mechanism and make sure it is securely locked.
Insert the handlebars onto the stem using the positioning guides and the positioning pin to route the cable.
Place the holes of the head unit clip opposite the holes in the stem and handlebars.
Tighten the two screws on each side using the 3 mm hex key provided.
Pull the brake lever and insert the head of the brake cable into the brake lever bracket.
Thread the cable through the slot in the brake lever until the sheath fits into the stop on the brake lever. You must pull on the sheath to perform this operation.
Check the brake operation by actuating the brake lever. The brake calliper must apply pressure to the rotor to prevent the wheel from turning.
Carry out steps 7, 8 and 9 for each brake lever. Verify that the right lever operates the brake system for the front wheel and that the left lever operates the rear brake system.

Folding and unfolding the scooter To unfold the scooter:

Press the side of the head unit clip to open and release it from the head unit mount .
Pull the head unit clip out of the head unit mount.
Lift the stem into a vertical position.
Lift the folding mechanism lever until the stem safety locks and make sure it is securely locked.

To fold the scooter:

Lower the stem folding lever by lifting the safety hook.
Lower the stem until it sits parallel to the deck.
Press the side of the head unit clip to engage it in the head unit mount.

Warning:
The head unit clip is part of the folding system and must not be used to carry luggage. Attaching any load to the handlebars will affect the stability of the electric scooter.

Changing the brake pads
Remove the wheel and remove the worn brake pads from the brake calliper. Position the new pads in the calliper so that the braking surfaces are in contact. Do not touch the braking surfaces. Insert the brake pads one after the other into the brake calliper.If your brakes don’t work correctly please consult your local retailer for assistance.

How to use your Carrera impel is-2

Step 1: Check that the silicone cap covers the charging connector and that your product is not damaged.
Step 2: Unfold the scooter as recommended in section “Ill. Folding and unfolding the scooter” and press the “On/Off’ button. Enter the electronic lock code as described in section C.11. Electronic locking of the scooter”.
Step 3: Once the scooter is switched on, check that the stand is folded up, put one foot on the board and start gaining forward momentum by pushing on the ground with the other foot, without using the throttle.
Step 4: You must reach a speed of 3 km/h [1.9 mile/h] to be able to use the throttle and switch to electric mode. To accelerate, use the trigger or throttle lever near your right hand. Once in motion, you can adjust the speed ratio using the “+” or “-” control button.
Step 5: To brake, release the trigger or throttle lever and pull the brake levers.
Step 6: Once your ride is complete, press and hold the On/Off button for 3 seconds to turn the scooter off.
IMPORTANT:
To avert any danger, sharp turns should always be avoided when travelling at high speed. Keep your body balanced when turning to avoid falling over due to high speeds or a shifting centre of gravity.

Display interface
The control screen, located on the handlebars, shows you the status of the scooter, its speed, the battery charge level, the front and rear lights and any error codes. It also allows you to set and enter the electronic lock code.

Electronic locking of the scooter
By default, the scooter is equipped with an electronic locking system that prevents the scooter from being switched on. When the power button is pressed, the control screen beeps and requires the unlock code to be entered. The default code is 000. If you attempt to move the scooter without entering the code, the brakes will be activated, the front and rear lights will flash and a continuous beep will sound.

Caution, this does not prevent the scooter from being physically stolen. For this purpose, use the built-in anti-theft device (see D.1.)

Entering the code to unlock the scooter

Hold the “On/Off’ button for 3 seconds to switch the scooter on.
Enter the code using the buttons on the control panel.
The cursor will move to the first digit of the code – increase or decrease its value using the “+” and “-” buttons. Briefly press the “On/Off’ button to confirm and move to the next digit.
Briefly press the “On/Off’ button twice to confirm the code entry.

Activating the lock code

Hold the “On/Off’ button for 3 seconds to switch the scooter on.
Simultaneously press and hold the “On/Off’ and “+” buttons for 5 seconds to activate/deactivate the code lock feature.

Changing the scooter’s lock code

Hold the “On/Off’ button for 3 seconds to switch the scooter on.
Simultaneously press and hold the “On/Off’ and “-” buttons for 10 seconds to reset the lock code. The cursor will move to the first digit of the code – increase or decrease its value using the “+” and “-” buttons. Briefly press the “On/Off’ button to confirm and move to the next digit.
Briefly press the “On/Off’ button twice to confirm the new code.

Control buttons

The control button panel is located on the left side of the handlebars
Switching on: Briefly press the “On/Off” button to switch on the scooter.
t Switching off: Press and hold the “On/Off” button for 3 seconds to switch off the scooter.
Lights: Press and hold the “+” button for 2 seconds to turn on/off the headlight and taillight.
t Speed modes: Once moving, press the “+” or “-” button to switch speed modes.
seed mode 1: 6 km/h [3. 7 mile/h] max speed Pedestrian mode: Press and hold the “-” button for 3 seconds to enable the pedestrian mode (speed limited to 3 km/h [1.9 mile/hi). On the display, the number “6” blinks and the taillight flashes every 3 seconds.

Error codes
If a malfunction occurs while using your Carrera impel is-2, simultaneously press and hold the “On/Off’ and “-” buttons for one second, one of the following error codes will appear on the screen:

Using the anti-theft device
At the bottom of the stem is a built-in anti-theft device in the form of a steel cable that can be locked with a numerical code. This lock is a low security lock and is intended for use as a visual deterrent only.

Remember that you can injure yourself by loosing control, colliding or falling off the Carrera impel is-2.
Do not use the Carrera impel is-2 in an unsafe environment where flammable products, vapours, liquids, dust or fibres may be present and cause a fire or explosion.
It is prohibited to mount a seat on the electric scooter for use in a seated position.

User weight limit

Guarantee the user’s safety.
Avoid damaging the Carrera impel is-2 due to overloading.
- The maximum weight supported by the Carrera impel is-2 is 120 kg
- The weight of the user and his/her belongings must not exceed the maximum weight indicated in this manual. Overloading may cause the user to fall or be injured and may damage the Carrera impel is-2. In addition, the weight of the user must not be less than the minimum weight of 20 kg. Failure to comply with the recommendations may result in the Carrera impel is-2 losing its ability to safely decelerate or stop while going downhill.
- It is forbidden for more than one person to ride the scooter. The Carrera impel is-2 is designed to be ridden by one person only.

Maximum travel distance
The maximum travel distance varies depending on several factors, such as:

Terrain: Smooth, flat terrain increases the travel distance. Sloping terrain reduces the distance.
Avoid driving on steep slopes.
User weight: The user weight affects the distance travelled.
Ambient temperature: Storing and using the Carrera impel is-2 at the recommended temperature may increase the travel distance; using the Carrera impel is-2 outside of this temperature range reduces the travel distance.
Speed and driving habits: Consistent, low operating speed increases the driving distance; conversely, frequent starting, stopping, accelerating and decelerating reduces the driving distance.
Do not start and stop suddenly.
Do not use the Carrera impel is-2 on slopes that are too steep. Accelerating on too steep a slope can cause the engine and battery to overheat.
When the battery is charged, the typical range in average conditions is 20km [12.4 mile].

Cruise Control

Hold the throttle in the same position for 6 seconds
The speedometer icon will light up to show it is active

charge

Charging procedure
Please charge the battery of the electric scooter as follows:

Insert the charger plug into the scooter battery (charging connector) by lifting the silicone cap that covers the charging connector on the front right side of the deck.
- Check that the charging connector is dry and plug the charger’s power cable into a nearby mains socket.
- When charging, the LED on the charger will turn red to indicate proper operation. When it turns green, it means that the battery is charged.
- To complete charging, you must unplug the mains plug and then the plug connected to the battery. Finally, close the battery socket cap.
- Unplug the mains plug.

IMPORTANT:

Charging for too long may shorten battery life. Do not leave your Carrera impel is-2 connected to the charger overnight.
Make sure to fully charge your Carrera impel is-2 battery the first lime and everytime you charge ii to maximise its service life.
Charge in a clean and dry environment.
Do not charge the battery if the charging plug is wet.

Battery
This electric scooter is equipped with a high-quality Li-ion battery. The Li- ion batteries have no memory effect and a wide temperature tolerance range from -10 to 40°C. The battery is placed in a compartment under the scooter’s deck. To ensure maximum battery life and to protect the battery from damage, please follow the use and care instructions below.

Battery life
After charging your battery, it is advisable to let it rest for 20 to 30 minutes before use. The operating life of your battery depends on several factors:

The choice of the mode of assistance The weight of the user
The gradient (slope)
Tyre inflation
The wind
Starting and stopping frequency Outdoor temperature

Warning, precautions
It is recommended to recharge the batteries on a regular basis, or after each use. There is no memory effect on this battery. To maximize the service life of your battery, it is recommended:

Avoid very hot and very cold places (ideal charging temperature 20°C)
Allow the battery to cool down 30 minutes after use.
If the Carrera impel is-2 stops due to overheating, place the Carrera impel is-2 in a cool, dry place and wait for the battery and hub motor to cool before using it again.

Storage

Before storing it, fully charge your Carrera impel is-2 to prevent over-discharging of the battery due to a prolonged period of non-use.
Do not charge the battery if the temperature is below 0°C; place the Carrera impel is-2 in a warmer environment (more than 5°C) before charging.
You must protect your Carrera impel is-2 from any loss in performance due to dust.
Store your Carrera impel is-2 indoors in a dry place at room temperature (20° C).

WARNING:
To ensure your safety, never disassemble the Carrera impel is-2 or your warranty will be void.
RECOMMENDATION:
If the scooter is not used frequently over a period of time, it should be fully charged every 60 days. The scooter should be stored in a dry, sheltered place at a temperature between 5 and 35°C. Otherwise, the warranty will not apply for such negligence.

Technical Specifications

Scope of Warranty In case of problems:

The supplier warranty is valid for normal product use as defined in the user manual for a period of 2 years concerning the product and 1 year for the battery.
Damages due to a cause unrelated to the device are excluded from this warranty.
In particular, the warranty does not apply if the device has been damaged by an impact or fall, incorrect operation, non-compliant connection, lightning, mains overvoltage, insufficient protection against heat, humidity or frost.
The warranty does not cover the user manual.
The warranty does not cover normal wear and tear of the product (tyres, brake cable and sheath, brake pad, wear of the footboard, wear of the mudguard, wear of the plastic protective covers, etc.).
The warranty does not cover any deterioration of the product due to misuse, including but not limited to those caused by collisions with objects or falls.
The warranty does not cover any use of the product that does not comply with the precautions for use stipulated in the user manual.
The warranty does not cover defects caused to the product by an accessory not supplied.
The warranty does not cover any damage to the battery.
The warranty does not cover the product or its accessories if it has been disassembled or modified in any way.
The warranty does not cover any product not identifiable by its serial number. If parts have been removed, erased, altered or made illegible, the warranty does not apply.
The warranty does not cover damage to the product as a result of exposure to moisture, extreme heat or cold, corrosion, oxidation, or exposure to any liquid whatsoever.
The warranty does not cover any deformation, damage, or breakage of the main frame as a result of a sudden fall, excessive overload, or repeated shocks.

Information on Waste Disposal for Consumers of Electrical & Electronic Equipment This mark on a product and/or accompanying documents indicates that when it is to be disposed, it must be treated as Waste Electrical & Electronic Equipment (WEEE).Any WEEE-marked waste products must not be mixed with general household waste, but kept separate for the treatment, recovery and recycling of the materials used.For proper treatment, recovery and recycling; please take all WEEE marked waste to your Local Authority Civic waste site, where it will be accepted free of charge.
If all consumers dispose of Waste Electrical & Electronic Equipment correctly, they will be helping to save valuable resources and preventing any potential negative effects upon human health and the environment, of any hazardous materials that the waste may contain.Please recycle your spent batteries.
Batteries should not be disposed of in unsorted municipal waste, but separately collected to facilitate the correct treatment and recycling of the substances they contain. The recyclingof batteries ensures the recovery of these valuable materials and prevents any potentially harmful effects upon both the environment and human health.Please contribute to battery recycling by segregating all spent batteries and actively participating in their collection and recycling. Various battery collection schemes will be in operation in different areas of the country. However, battery collection bins will be available at retail stores that sell batteries as well as at schools, libraries and other public buildings.
WARNING!
Protective equipment should be worn. To avoid serious injury, always wear protective equipment: shoes, helmet, gloves, knee pads, elbow pads and wrist protectors.