HYUNDAI CRM 129 SU CD MP3 SD MMC USB Player Instruction Manual

HYUNDAI CRM 129 SU CD MP3 SD MMC USB Player

SAFETY INFORMATION

Thank you for purchasing this product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, keep this manual in a safe place for future reference.

PRECAUTIONS

• Use only in a 12-volt DC negative-ground electrical system.
• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.
• When replacing the fuse, be sure to use one with an identical amperage rating.
• Using a fuse with a higher amperage rating may cause serious damage to the unit.
• DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes.
• Make sure those pins or other objects do not get inside the unit, they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.
• If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car become normal before operating the unit.
• Keep the volume at a level at which you can hear outside warning sounds (horns sirens, etc.).
• Stop the car before performing any complicated operation.

CD NOTES

• Playing a defective or dusty CD can cause dropouts in sound.
• Handle the disc by holding its inner and outer edges. Do not touch the surface of the unlabeled side of the disc.
• Do not touch the unlabeled side.
• Do not attach any seal, label or data protection sheet to either side of a disc.
• Do not expose a CD to direct sunlight or excessive heat.
• Wipe a dirty CD from the center outward with a cleaning cloth.
• Never use solvents such as benzine or alcohol.
• This unit can not play 3-inch (8 cm) CDs.
• Never insert a 3-inch CD contained in the adapter or an irregularly shaped CD. The unit may not be able to eject it, resulting in a malfunction.
• In addition to ordinary CDs, this unit can play back a CD-R/CD-RW/MP3/UDF/CD-TEXT.

CAUTION: Please power off this unit at once and send it back to the after-sales service center or the dealer/distributor you purchased from if one of the following symptoms is found:

1. Water or other obstacle enters the unit;
2. Smoking;
3. Peculiar smell.

To provide a clear demonstration and an alternative for easy understanding of the operation of this unit, graphic illustration was used. However, this illustration is not necessary printed as the actual image found on the unit.

PANEL CONTROLS

1. Press to eject disc.

2. Power / Toggle the audio source

3. Previous / next track

4. Search (long press)

5. Band switch: FM1  FM2  FM3  AM1 AM2

6. Unlock the front panel.

7. MP3 mode – Search function

8. CD mode – No function

9. AUX mode – No function

10. USB mode – Search function

11. RADIO mode – Program type

12. Traffic announcements identification. (long press)

13. MUTE

14. Sound effect setting

15. Button 1: Scan play / Preset station 1
    Button 2: Repeat play / Preset station 2
    Button 3: Random play / Preset station 3
    Button 4: Play / Pause / Top play (long press) / Preset station 4
    Button 5: Previous folder / Preset station 5 10 tracks down (long press) /
    Button 6: Next folder / Preset station 6 10 tracks up (long press) /

16. Display switch

17. System setup (long press)

18. Aux-in jack

19. USB connector

20. Disc slot

21. Adjust volume level / Confirm (press)

22. Scan play / Preset scan

23. Auto memory store (long press)

GENERAL OPERATION

Power On/Off Button
Press the [ ] button to turn the unit on when the vehicle ignition switch is on. Press and hold the button to turn the unit off.
Adjust Volume Level
Rotate the knob to adjust the volume level. Rotate it clockwise to increase and anticlockwise to decrease the volume.
Audio Mute
Press the [MUTE] button to mute the volume from the system. “MUTE” will appear on the display panel and the volume will be muted. Press the [MUTE] button again, or rotate or press the VOL/MENU control to return the volume level to the setting in use before the Mute function was activated.
Mode Button (SRC)
Press the [ ] button to change between Radio, DISC (when the disc is in), USB (when USB is connected), Card (when SD/ MMC card is in) or AUX play.
Auxiliary Input
To access an auxiliary device:

1. Connect the portable audio player to the AUX interface on the front panel.
2. Press the [ ] button to select Aux-In mode.
   Press SRC again to cancel Aux-In mode and go to the next mode.

Display Selector (DISP)
This unit can display either the clock time or radio frequency/CD player functions. Ordinarily, the radio frequency or CD player track indication is displayed, but the unit will display the time when the DISP button is pressed. The time will display for approximately 5 seconds then return to the radio or CD player function display.
SOUND SETTING
Press and hold the [MUTE] button to enter sound effect setting mode. The first press shows the current EQ. Rotate the knob to change BEAT EQ in this order:
OFF-POP CLASSIC ROCK JAZZ  CUSTOM
Rotate the knob to change CUSTOM, and press the knob, press [ ] or [ ] button to select it including BAS-G  TRE-G, rotate the knob to select a value.
BAS-G / TRE-G: (-7) – (+7)
Press and hold the [MUTE] button, then press the [ ] or [ ] button to select USER preset including:
BALANCE FADER LOUD, rotate the knob to select a value.
BALANCE: LEFT 1–7 CENTER RIGHT 1–7
FADER: FRONT 1–7 CENTER REAR 1–7
LOUD: ON/OFF.

CD/MP3 OPERATIONS

THIS UNIT CAN PLAY BACK MP3 FILES PRECAUTIONS WHEN CREATING MP3 FILE Usable sampling rates and bit rates

1. MP3: Sampling rate 8 kHz – 48 kHz, Bit rate 8 kbps – 320 kbps / VBR

File extensions

1. Always add a file extension “.MP3” to MP3, file by using single byte letters. If you add a file extension other than specified or forget to add the file extension, the file cannot be played.
2. Files without MP3 data will not play. The files will be played soundlessly if you attempt to play files without MP3 data.
   • When VBR files are played, the play time display may differ the play location.
   • When MP3 files are played, a little no sound part is caused between tunes.

Logical format (File system)

1. When writing MP3 file on a CD-R disc or CD-RW disc, please select “ISO9660 level
2. 2 or Joliet or Romeo” or Apple ISO as the writing software format. Normal play may not be possible if the disc is recorded on another format.
3. The folder name and file name can be displayed as the title during MP3 play but the title must be within 32 single byte alphabetical letters and numerals (including an extension).
4. Do not affix a name to a file inside a folder having the same name.

Folder structure
A disc with a folder having more than 8 hierarchical levels will be impossible.
Number of files or folders

1. Up to 999 files can be recognized per folder. Up to 3000 files can be played.
2. Tracks are played in the order that they were recorded onto a disc. (Tracks may not always be played in the order displayed on the PC.)
3. Some noise may occur depending on the type of encoder software used while recording.

EJECT FUNCTION
Just pressing the [ ] button, ejects the disc even if the power to the unit was not turned on.

Notes:

• If you force a CD into before auto reloading, this can damage the CD.
• If a CD (12 cm) is left ejected for 15 seconds, the CD is automatically reloaded (Auto reload).

LISTENING TO A DISC ALREADY LOADED IN THE UNIT
Press the [ ] button to select the CD/MP3 mode. When the unit enters the CD/MP3 mode, play starts automatically.
LOADING A CD
Insert a CD into the center of the CD SLOT with the label facing up. The CD plays automatically after loading.

Notes:

• Never insert foreign objects into the CD SLOT.
• If the CD is not inserted easily, there may be another CD in the mechanism or the unit may require service.
• Discs without the or TEXT TEXT mark and CD-ROMs cannot be played by this unit.
• Some CD-R/CD-RW discs may not be usable.

PAUSING PLAY

1. Press the [4 ] button on the front panel or the [ ] button on the remote control to pause play. “PAUSE” appears in the display.
2. Press the above button again to resume CD play.

DISPLAYING CD TITLES
This unit can display title data for the MP3 disc. When SCROLL is OFF, each time you press the [DISP] button to change the title display.
MP3 DISC
FILE FOLDER TITLE ARTIST ALBUM

Notes:

• If MP3 disc is not input TAG, “NO TITLE” appears in the display.
• Only ASCII characters can be displayed in Tags.

SELECTING A TRACK

Track-up

1. Press the [ ] button to move to the beginning of the next track.
2. Each time you press the [ ] button, the track advances to the beginning of the next track.
3. For MP3 disc, press and hold the [6] button (1 sec.) to move ahead to +10 tracks.

Track-down

1. Press the [ ] button to move back to the beginning of the current track.
2. 2. Press the [ ] button twice to move back to the beginning of the previous track.
   For MP3 disc, press and hold the [5] buton (1 sec.) to move back to -10 tracks.

FAST-FORWARD/FAST-REVERSE

Fast-forward
Press and hold the [ ] button.
Fast-reverse
Press and hold the [ ] button.
For MP3 discs, it takes some time until the start of searching and between tracks. In addition, some error may occur in playtime.
FOLDER SELECT
This function allows you to select a folder containing MP3 files and start playing from the first track in the folder.

1. Press the [5] or [6] button. Press the [5] button to move the previous folder. Press the [6] button to move the next folder.
2. To select a track, press the [ ] or [ ] button.

SEARCH FUNCTION
Press the [MENU], then rotate the knob to choose FOLD sch or TRK sch. Direct Song/File Access

1. Press the knob to enter the track list search mode.
2. Turn the knob to select a digit.
3. Press the knob to confirm entry and the tens digit will flash.
4. Turn the knob to select the digit.
5. Repeat the above steps to enter the hundreds and thousands digit, if necessary.
   NOTE: The unit will only allow the selection of digits that correspond with the number of files on the media you are searching. Once the track number appears on the screen, press the knob to play the selected song/file.

Searching Folders/Files

1. Press the knob to enter the folder list search mode.
2. Turn the knob to select a folder.
3. Press the knob to enter the file list search mode. And then the track list appears in the display.
4. Turn the knob to select a track.
5. Press the knob to play. When playback MP3 file, this function is performed in the current folder.

TOP FUNCTION
The top function resets the CD player to the first track of the disc. Press and hold the [4 ] button (1 sec.) to play the first track (track No. 1) on the disc. In case of MP3, the first track of the current folder will be played.

OTHER VARIOUS PLAY FUNCTIONS

Scan play
This function allows you to locate and play the first 10 seconds of all the tracks recorded on a disc. Press the [1] button to perform scan play.
Repeat play
This function allows you to play the current track repeatedly or play a track currently being played in the MP3 folder repeatedly.
CD:

1. Press the [2] button once or more until “RPT ON” appears on the LCD to perform repeat play.
2. Press [2] button repeatedly until “RPT OFF” appears on the LCD to cancel repeat playback.

USB/SD/MMC MP3 PLAYBACK

1. Loading SD/MMC Card
   Insert the SD/MMC card into the slot. The unit will play the music automatically and the LCD will show CARD.

2. Take out SD/MMC Card
   Push SRC button and switch to non CARD mode, slightly press SD/MMC card, take out the card when it was popped out.

3. Loading USB equipment
   Open the rubber cap, insert the USB into the connector and the unit play the music in the USB storer automatically, and the LCD will show USB.

4. Take out USB equipment
   Push the SRC button and switch to non USB mode, then take off the USB storer, close the rubber cap.

USB/SD/MMC Notes

USB functions (flash memory type) MP3 music play.

1. SD/MMC card support.
2. USB flash memory 2 in 1 (SD/MMC ) support.
3. Fat 12/fat 16/fat 32 is possible.
4. File name: 32 byte / dir name: 32 byte / tag name: 32 byte
5. Tag (ID3 tag ver 2.0) title/artist/album: 32 byte support.
6. Multi card reader not support.
7. USB 1.1 support, USB 2.0 support (It can not support USB 2.0 speed. Just, get the same speed with USB 1.1).
   Note: all kinds of USB devices are compatible with the unit.

TUNER OPERATION

Band
During radio play, press the [BAND] button to choose between three FM, two AM bands. The indication “AM”, “FM” appears on the display panel according to your selection.
Up Tuning
Press the seek up [ ] button to tune stations upward step-by-step. The current frequency will be shown in digital format on the display panel. Press and hold the seek [ ] button to the next available station.
Down Tuning
Press the seek down [ ] button to tune stations downward step-by-step. Press and hold the seek down [ ] button to the previous available station.
Auto Store
Press the [PS/AS] button to scan preset stations 1–6. Hold it to automatically select six strong stations and store them in the current band. The new stations replace stations already stored in that band.

RDS (RADIO DATA SYSTEM)

RDS service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available.|
RDS Basics
AF (Alternative Frequency): When the radio signal strength is poor, enabling the AF function will allow the unit to automatically search another station with the same PI (Program Identification) as the current station but with stronger signal strength.
PS (Program Service name): The name of station will be display instead of frequency.
AF Mode: Long press the [DISP] to enter menu mode, then Press [ ] or [ ] button to show AF mode, rotate the knob to select AF ON or OFF.
AF on: AF function is activated.
AF off: AF function is disabled.
Remark: AF indicator on LCD will flash until RDS information is received. If RDS service is not available in your area, turn off the AF mode.
REG Mode: Long press the [DISP] to enter menu mode, then Press [ ] or [ ] button to show AF mode, rotate the knob to select REG mode on and off.
REG on: AF function will implement the regional code (of the PI) and only stations in the current region can be tuned automatically.
REG off: AF function will ignore the regional code (of the PI) and stations in the other regions can also be tuned automatically.
CT Service (Clock Time)
When receiving an RDS station, the CT (Clock Time) service automatically adjusts the time.
Traffic Announcements
Some RDS FM stations periodically provide traffic information. TP (Traffic Program Identification) Broadcasting of traffic information. TA (Traffic Announcements Identification) Radio announcements on traffic conditions.
TA Mode: Press the [MENU] for more than 2 seconds to turn on/off the TA function. When TA mode is turned on, the TA indicator will blink. When traffic announcement is received, the TA indicator will display. The unit will temporarily switch to the tuner mode (regardless of the current mode) and begin broadcasting the announcement at TA volume level. After the traffic announcement is over, it will return to the previous mode and volume level. When TA is turned on, SEEK, SCAN, and AMS functions can only be received or saved when traffic program identification (TP) code is received.
EON (Enhanced Other Networks)
When EON data is received, the EON indicator lights and the TA and AF functions are enhanced.
TA: Traffic information can be received from the current station or stations in other network.
AF: The frequency list of preset RDS stations is updated by EON data. EON enables the radio to make fuller use of RDS information. It constantly updates the AF list of preset stations, including the one that currently tuned into. If you preset a station around the area at your home, you will later be able to receive the same station at an alternative frequency, or any other station serving the same program, EON also keeps track of locally available TP stations for quick reception.
PTY Reception ( Program Type)
RDS FM stations provide a program type identification signal. Example: news, rock, info, sport, etc.
PTY Type Preset
Press the [MENU] to enter PTY mode. Rotate the knob to select the desired program type. Then press the knob to confirm.

MENU FUNCTION

At all mode, press and hold [DISP] button to enter system setup. Press [ ] or [ ] button to select options, rotate the knob to adjust.
AF ON/OFF mode
Rotate the knob to choose alternative frequency on or off.
REG ON/OFF mode
Rotate the knob to choose REG on or off.
DX/LO (RADIO mode)
Rotate the knob to choose radio local or distant at RADIO mode.

• LO: Only stations with strong signal can be received.
• DX: Stations with strong and weak signals can be received.

STEREO/MONO mode
Rotate the knob to choose FM stereo or mono.
SCROLL: ON/OFF
For track information that is longer than the display panel: When SCROLL is ON, the LCD will display ID3 TAG information cyclely, e.g: TRACK FOLDER FILE ALBUM TITLE ARTIST  TRACK  …
When SCROLL is OFF, the LCD will display one of the ID3 TAG information, the default is TRACK, but user can adjust it to other ID3 TAG information by pressing [DISP] button.
BEEP: ON/OFF
Rotate the knob to choose the button beep sound ON or OFF.
12/24H
Rotate the knob to choose a time format: 12 or 24 hours.
CLOCK
Press the knob to enter clock setting mode, rotate the knob to set clock, press [ ] or [ ] button to select hour or minute, press and hold the knob to confirm.

ELECTRICAL CONNECTIONS

INSTALLATION GUIDE

Installation Opening
This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 4.75 mm – 5.56 mm thick in order to be able to support the unit. If the opening is too small, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check for sufficient space behind the dashboard for the unit chassis.
Reset
Press the RESET button with a pointed object to reset the unit to its original status.
Note: Press the RESET button will erase the clock setting and stored stations.
Installation Procedures

1. If relevant, remove any other audio system from the car.
2. Insert the mounting sleeve into the dashboard. Fix it firmly in place by folding down the metal tabs.
3. Perform the required electrical connections.
4. Then check that everything works before installing the main unit.
5. Remove the two screws on the top of the unit, otherwise, the unit will not work.
6. Install the car radio in the dashboard using the supplied screws (M5 x 6mm).
7. Attach the outer trim frame.

CAUTIONS:
Assembly is necessary to do in the service center. The car radio must not be installed in the excluded zone of head impact!

ANTI-THEFT SYSTEM
This unit is equipped with a detachable panel. Removing this panel makes the radio totally inoperable.
Remove the detachable panel

1. Press button.
2. Hold the part popped out and pull the panel out.
3. Gently press the button of the case and open the cover. Place the panel into the case and take it with you when you leave the car.

Install detachable panel

1. Fix the right part of the face plate in the panel slot of the unit.
2. Press down the left side of the face plate until it clicks into the panel slot.

Remove the unit

1. Switch off the power of the unit.
2. Remove the panel and the trim plate.
3. Insert both L-Keys into the hole on the front of the set until they lock.
4. Pull out the unit.

TROUBLESHOOTING

The following checklist can help you solve some problems which you may encounter when using the unit. Before consulting it, check the connections and follow the instructions in the user manual. Do not use the unit in abnormal conditions, for example without sound, or with smoke or foul smell can cause fire or electric shock, immediately stop using it and call the store where you purchased it.

General

The unit will not switch on.

| Car ignition is not on. The cable is not properly connected.

The fuse is burnt.

| Turn your car key in the ignition.

Check the cable connection. Replace the fuse with a new fuse

of the same capacity

No sound.| Volume is set at a minimum or the mute function is on.| Check the volume or switch the mute function off.
The unit or screen does not work normally.| The unit system is unstable.| Press the RESET button.
DISC mode

The appliance will not play discs.

|

The disc is inserted incorrectly. The disc is dirty or damaged.

| The disc must be inserted

with the label side facing up.

Clean the disc and check

for damage. Try another disc.

Sound skips due to vibration.

|

The mounting angle is over 30˚. The mounting is unstable.

| Adjust the mounting angle to less than 30˚.

Mount the unit securely

with the supplied parts.

TUNER mode
Unable to receive stations.| The antenna is not connected properly.| Connect the antenna properly.
Poor quality reception of radio station.| The antenna is not fully extended or it is broken.| Fully extend the antenna and if broken, replace it with a new one.

Preset stations are lost.

| The battery cable is not properly connected.| Connect the permanent live on the unit to the permanent live on the vehicle.
USB/SD/MMC mode
Unable to insert USB device or SD/MMC card.| The memory card or USB device has been inserted the wrong way round.|

Insert it the other way around.

The USB device or SD/MMC card cannot be read.

|

NTFS format is not supported.

| Check that the file system is in FAT or FAT32 format. Due to different formats, some models of storage devices or MP3 players may not be read.

SPECIFICATIONS

General
Power supply: 12 V DC (11 V – 16 V) Test voltage 14.4 V, negative ground
Maximum power output: 160 W (40 W x 4)
Continuous power output: 20 W x 4 channels (4 Ω,10 % T.H.D.)
Suitable speaker impedance: 4 Ω (4 to 8 Ω allowable)
Pre-Amp output voltage: 2.0 V (CD play mode: 1 kHz, 0 dB, 10 kΩ load)
Fuse: 15 A
Dimensions (W x H x D): 178 x 50 x 166 mm
Weight: 1.7 kg
Aux-in: ≥ 300 mV
FM Stereo Radio
Frequency range: 87.5 – 108.0 MHz (Europe)
Usable sensitivity: 8 dBμ
Quieting sensitivity (S/N = 50 dB): 12 dBμ
Frequency response: 30 Hz – 15 kHz
Stereo separation: 30 dB (1 kHz)
Image response ratio: 50 dB
IF response ratio: 70 dB
Signal/noise ratio: > 55 dB
AM (MW) Radio
Frequency range: 522 – 1620 kHz
Usable sensitivity (S/N = 20 dB): 30 dBμ
Disc Player
System: Disc digital audio system
Frequency response: 20 Hz – 20 kHz
Signal/noise ratio: > 80 dB
Total harmonic distortion: Less than 0.20 % (1 kHz)
Wow and flutter: Below measurable limits
Channel separation: > 55 dB
Components
Mounting collar: 1
Machine screws M5 x 6mm: 4
Mounting bolt (50 mm) L-key 2: 1
Operating instructions: 1
Trim plate: 1
Removable face plate case: 1
Rubber cushion: 1
Note: Specifications and the design are subject to change without notice due to improvements in technology.

WARNING: Do not use this product near water, or in wet areas to avoid fire or injury of electric current. Always turn off the product when you don’t use it or before a revision. There aren’t any parts in this appliance that are reparable by consumers. Always appeal to a qualified authorized service. The product is under a dangerous tention.

Disposal

Old electrical appliances used batteries and accumulators disposal

This symbol appears on the product, on the product accessories, or on the product packing means that the product must not be disposed of as household waste. When the product/battery durability is over, please, deliver the product or battery (if it is enclosed) to the respective collection point, where the electrical appliances or batteries will be recycled. The places, where the used electrical appliances are collected, exist in the European Union and in other European countries as well. By proper disposal of the product, you can prevent possible negative impacts on the environment and human health, which might otherwise occur as a consequence of improper manipulation with the product or battery/accumulator. Recycling of materials contributes to the protection of natural resources. Therefore, please, do not throw the old electrical appliances and batteries/accumulators in the household waste. Information, about where it is possible to leave the old electrical appliances for free, is provided at your local authority, at the store where you have bought the product. Information, on where you can leave the batteries and accumulators for free, is provided to you at the store, at your local authority.

References

• Hyundai-electronics.cz
• ASEKOL
• Úvod - ECOBAT
• Hyundai Electronics– Hyundai CZ
• SEWA - OZV | elektroodpad | batérie | obaly

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>