BaByliss T830E Beard Trimmer for Long Beards Instruction Manual

: June 5, 2024
: BaByliss

Table of Contents

BaByliss T830E Beard Trimmer for Long Beards
TRIMMER FEATURES
CHARGING THE TRIMMER
USE ON THE MAINS
USE OF THE CUTTING GUIDE
MAINTENANCE
BABYLISS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BaByliss T830E Beard Trimmer for Long Beards

T830E

Please carefully read the safety instructions before using the appliance.

TRIMMER FEATURES

35mm blades:
Moveable blade: CMS (Chrome-Molybdenum-Stainless Steel):
Fixed Blade: stainless steel
Hair collector
2 cut guides (1 to 20 mm and 16 to 35 mm with a 0.5 mm pass)
ON/OFF switch
Wheel to adjust the cutting length
Power indicator light
Trimmer charging plug
Cleaning brush

CHARGING THE TRIMMER

Insert the plug into the appliance and connect the adapter. Before using the trimmer for the first time, allow it to charge for 16 hours. Make sure the trimmer’s switch is in the OFF position.
Check that the charging indicator light is on.
A full charge provides a minimum of 60 minutes’ use of the trimmer.
Subsequent charges should be 8 hours.

IMPORTANT INFORMATION REGARDING THE NI-MH BATTERIES OF THIS UNIT

To obtain and maintain the longest battery life possible, allow it to charge for 16 hours approximately every three months. Moreover, full battery life of the unit will only be obtained after three complete recharge cycles.

USE ON THE MAINS

To use the unit on the mains, plug the cord directly into the unit. Plug the unit, in the OFF position, into the mains and switch ON (if the battery is very weak, wait about 1 minute).

IMPORTANT! Use only the adaptor that is supplied with the trimmer.

USE OF THE CUTTING GUIDE

IMPORTANT: Always position the cutting guide BEFORE switching the appliance on; always switch the appliance off before positioning the cutting guide.

To remove the cutting guide, first, adjust the cutting length to maximum (20 mm). With the motor off, remove one side and then the other, to release the guide (Fig. 1).
To replace the cutting guide, first, adjust the cutting length to a minimum (1 mm). With the motor off, clip on one side and then the other (Fig. 2).
Use the adjustment wheel to select the desired cutting length.

TURNING IT ON AND USING IT
Turn the adjustment wheel to select a cutting length. Operate the ON/OFF button. You can change the cutting length at any time.

IMPORTANT! Make sure you keep the cutting guide flat against the skin. That is, the tips of the teeth and the little corners protruding from the comb should always be in contact with the skin. If not, the precision of the cut may change (Fig. 3-4).

MAINTENANCE

Regular maintenance of the blades and hair collector will keep the trimmer in optimal working condition.

Removable blades

To make cleaning easier, the BaByliss trimmer blades can be removed. Make sure that the trimmer is off and remove the cutting guide. Hold the trimmer with the blades pointing up and remove them by pressing their points.(Fig. 5). Carefully brush the blades using the cleaning brush to remove hair. Rinse the blades. The device must never come into contact with water. Let the blades dry in the open air before putting them back onto the device.

Self-lubricating blades

The blades of your trimmer have a reservoir pad for releasing the necessary amount of oil for proper operation of your trimmer, time after time. Nevertheless, it is recommended that it be refilled occasionally when you notice performance is not as high. Remove the blades as described above. Squeeze a few drops of BaByliss oil onto the pad (Fig. 6). Then replace the blades on the trimmer. The BaByliss oil is specially formulated for the trimmer, it does not evaporate nor does it slow the blades. It is possible to obtain replacement blades when these are worn out or damaged.

Hair collector

For best hygiene, we recommend regularly removing the hair collector for cleaning: Remove the collector by pulling the upper part (Fig. 7) Empty the collector. Rinse the collector and let it dry in the open air before putting it back onto the device.

To replace the collector, place the lower part of the collector in the appropriate slot and finalize by clipping the upper part into place (Fig. 8).