Goldair GPPH770 Electronic Inverter Panel Heater with WiFi Instruction Manual

Goldair GPPH770 Electronic Inverter Panel Heater with WiFi

General Care and Safety Guide

YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

CAUTION

• In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they are supervised or have been given instruction concerning the use of the appliance by a person responsible for their safety
• Children should be supervised to ensure that they do not play with the appliance
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard

WARNING

• You must not cover this appliance Covering this appliance presents a fire risk and will activate the safety fuse permanently disabling the unit
• Do not use this appliance in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided
• To reduce the risk of fire, keep textiles, curtains, or any flammable material a minimum distance of 1 meter from the air outlet
• Use only the voltage specified on the rating label of the appliance
• Keep all objects at least 1 meter from the front and 150 mm from the sides of the appliance
• This appliance is intended for household use only and not for commercial or industrial use
• Indoor use only
• Use this appliance only as described in this manual Any other use is not recommended by the manufacturer and may cause fire, electric shock or injury
• Do not use the appliance if it has been dropped or damaged
• The common cause of overheating is deposits of dust or fluff in the appliance
• Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
• • Never use the appliance to dry clothes.
• Always unplug appliance when not in use.
• When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts are missing or the appliance has been damaged, contact the Customer Services Team.
• Do not use it if there are visible signs of damage to the appliance.
• Do not connect the appliance to the main supply until completely assembled and adjusted.
• Ensure hands are dry before handling the plug or main unit.
• Ensure appliance is on a flat, stable, heat-resistant surface.
• Do not operate with cord set coiled up as a heat build-up is likely, which could be sufficient to become a hazard.
• Carry out regular checks of the supply cord to ensure no damage is evident
• Do not operate this appliance with a damaged cord, plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Take to a qualified electrical person for examination, electrical service, or repair.
• Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area and is unrolled before use.
• It is recommended that this appliance is plugged directly into the wall socket. Power boards are not rated to supply power to high-wattage appliances.
• A correctly specified, an undamaged extension cord may be used with this appliance provided it is used in a safe manner.
• Do not remove the plug from the power socket until the appliance has been switched off.
• Do not remove the plug from the power socket by pulling the cord; always grip the plug.
• Do not place a cord under carpet or cover it with rugs or furniture. Arrange the cord so it cannot be tripped over.
• Don’t place appliances on bedding or on thick & long carpet where the openings may get blocked.
• Switch off and use the handle provided when moving
• Do not place the appliance close to a radiant heat source.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire, or damage to the appliance.
• Do not sit on the appliance.
• Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) and rinsed in hot soapy water only. Always remove the plug from the mains supply before cleaning.
• Do not operate in areas where petrol, paint, or other flammable liquids are used or stored.
• Do not use this appliance in the immediate surroundings of a bath, a shower, a swimming pool, or other liquids.
• The appliance must not be immersed in any liquids
• There are no user-serviceable parts installed in the unit
• Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards
• This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science, etc are stored
• If your appliance does not work or is not working properly, contact the place of purchase or the Customer Services Team.

“OVERHEAT PROTECTION” FUNCTION

The device is equipped with an automatic switch that is activated when the upper-temperature limit is reached The heater switches off automatically in case of overheating After eliminating the source of overheating, the heater will turn on automatically.

Components

Assembly Instructions

Before using this appliance, it must either be wall mounted or have the feet fitted This appliance has been supplied with 1-way screws’ for permanent installation of the feet This is a safety requirement for the New Zealand and Australian market.

FREESTANDING

1. Ensure the appliance is unplugged and power switches are off
2. Carefully turn the main body upside down on a scratch-free and stable surface Be careful to prevent damage to the cosmetic finish or your floor surfacing
3. Align the screw hole on the Heater Feet Bracket with the screw hole on the base of the appliance
4. Attach Heater Feet Bracket with the 1-way screws’ provided and ensure the bracket sits firmly in place (do not over-tighten)
5. Set appliance upright

NOTE: The wall bracket edges may be sharp It is recommended that if using as a free-standing appliance please remove the wall bracket from the back of the heater.

Installation Instructions

The appliance must not be located immediately below a socket outlet.

NOTE

• Your Panel Heater should be installed with at least 150 mm clearance from the floor and any other surrounding parts including other appliances and side walls At least 300 mm clearance from ceilings, shelves, and soft furnishings.
•  Do not run the power cord behind the heater.

WALL-MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON HEAT-RESISTANT WALLS THAT COMPLY WITH THE CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS.

WALL MOUNTED

1. Make sure the appliance is unplugged and power switches are off
2. Position the panel appliance within one meter of a wall socket Do not mount in front of or below the wall, socket Ensure there is at least 150 mm clearance on all sides of the appliance
3. Detach the mounting bracket from the back of the panel appliance by unscrewing the two locking screws (located on the top of the mounting bracket)
4. Position the mounting bracket on the wall and mark the hole positions with a pen or pencil and check they are horizontal with a spirit level Ensure the two bottom mount holes are at least 150 mm from the floor and drill holes as required
5. Secure the mounting bracket to the wall with the mounting screws ..(For masonry walls use the plastic sheaths)
6. Slot the back of the appliance onto the mounting bracket locating the bottom plugs first and secure with two locking screws
7. Plug the appliance into a standard 240 volts AC electrical outlet.

Operating Your Heater

Always choose a safe location for the heater, keeping in mind the safety precautions outlined Ensure all packaging has been removed from the unit before use Please follow the below instructions.

WARNING

• In order to avoid overheating or fire, do not cover the heater
• Keep all objects at least 1 meter from the front and 150 from the sides of the appliance
• Do not use this heater with a programmer, separate timer, remote control system, or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly
• Never leave this heater unattended when in use If mounted on castors, ensure the heater is on a flat, stable, heat-resistant surface.
• Once the heater is in a safe operating position and all switches are in the off position, insert the power plug into the mains outlet and switch on

CAUTION

• Ensure the power cord is not tight because if pulled it may partially pull the plug from the socket A partially inserted plug will overheat the plug and socket and could result in fire

Note: When the appliance is turned on for the first time, it may release a slight odor or smoke This odor or smoke is a normal occurrence caused by the initial heating of the heating elements and should not occur again.

Operating Your Heater

DISPLAY CONTROLS

• Indication of temperature mode Comfort
• Indication of a temperature mode Eco
• Indication of a temperature mode Anti Frost
• Display of function “Open Window”
• Indication of “Timer Off” function (to turn off)
• Heating mode indication
• Heating mode indication
• Indication of heating power levels
• Indication of work on a schedule (Wifi Only)
• Indication of Wi-Fi operation
• Control lock indication
• Control unlock indication
• Display target temperature

ERROR MESSAGES

• Temperature sensor malfunction. Contact customer services.
• Short circuit on temperature sensor channel. Contact customer services.
• Overheating of temperature sensor (exceeded +48 degrees). Turn off the heater to allow it to cool down.
• The ambient temperature has dropped too low (below 26 degrees). Turn off the heater to allow the ambient temperature to rise.

SETTINGS MENU DIAGRAM

Check that the heater main power switch is in the OFF position before plugging it into the mains supply

ON/OFF BUTTON

Hold down for 3 seconds to turn the heater ON/OFF The default temperature is 24 C

OPEN WINDOW

When this function is active if the temperature drops by 55°C or more within a 10-minute period, Anti Frost mode is switched on If in the time interval of 10 30 minutes the temperature continues to drop, the device will turn off If the room temperature rises by 22°C, then the last set mode will turn back on

CHILD LOCK

Hold down the left and right arrow simultaneously for 5 seconds to enable child lock The device controls cannot be changed To disable child lock, hold down the left and right arrow for another 5 seconds.

NAVIGATING THE MENU

• Use the buttons to navigate through all the menu options and the button to confirm your selection.

HEAT MODE

There are 3 temperature modes available for adjustment:

• Comfort Range from 1010°C to 3535°C
• Eco Deviation range from Comfort from 33°C to 77°C
• Anti Frost Range from 33°C to 77°C

Use the buttons to navigate and the button to firstly confirm your desired mode and then desired temperature Note Temperature can only be amended on the device when in Comfort mode If you press the left or right button in Eco/Anti Frost mode in order to amend the temperature, the heater will switch to Comfort mode.

POWER

Choose desired power mode between:

• Auto:  the heating element is inversely controlled
• Custom: choose desired heat setting between 1-5 using the buttons to navigate and the button to confirm.

TIMER

This device has a countdown timer that will allow you to set a specific amount of time before turning the heater off.

• Use the buttons and to navigate to the Timer function and turn the Timer function from OFF to ON.

Set the time for the desired length of time you would like the heater to remain on. For example, if you want the heater to turn off in 3 hours and 30 minutes you would set the timer to 03:30. To cancel the Timer, you must go back to the Timer function and amend it from ON to OFF.

Note: This device has a full weekly scheduler function available to operate via the app. Operating the scheduler and timer at the same time is not possible.

SETTINGS

• Use the buttons to navigate through all the menu options and the button to confirm your selection

DATE AND TIME

• Set the current date and time for the best functionality of your heater.

DISPLAY

• Brightness: Choose between 100 %%(default setting) and 50 screen brightness.

SOUND

• Choose to have sound when buttons are pressed ON/OFF
• The default setting is ON.

SERVICE

• Connection: Use this function to connect to the Goldair app To learn more about this device’s WiFi, please see the WiFi/App section of this manual
• Reset: Choose to reset the device to default settings
• Information: See the device’s current firmware version

WiFi Downloading and Setting up APP

This APP is supported only on 2.4GHz Wi-Fi channels. Please ensure your phone is 2.4GHz capable

Note: this device will only work within your home WIFI system. This does not operate on 3G or 4G internet connections. You will need a connection to your home Wi-Fi Tap REGISTER near the bottom of the screen. Read and agree to the Privacy Policy.  Add your email address. Tap ‘Obtain verification You will then receive an email with a verification code.

Download the Goldair mobile APP

• Open the APP Store or Google Play on your mobile phone.
• Open ‘Search’ and enter ‘Goldair’
• Click ‘GET’ and begin to download and install.

Once downloaded to your phone open the APP

• Tap REGISTER near the bottom of the screen.
• Read and agree to the Privacy Policy.
• Add your email address.
• Tap ‘Obtain verification

You will then receive an email with a verification code

• Enter the verification code from your email.
• Create a password.
• Then tap confirm.

If you haven’t received a verification code via email, tap the resend button, and when the verification code is received follow the above steps.

Your APP is now registered and ready for pairing to your device.

Pairing APP to Device

Details for pairing, this heater to the Goldair App can be found at the below website link Either scan the QR code below or enter the website into your browser

• https://www.goldair.co.nz/goldair-app
• https://www.goldair.com.au/goldair-app

Pairing Mode

To connect to the Goldair app you must ensure that your device is in pairing mode which is where the Wifi Icon is flashing. Most products will be in pairing mode after switching the device on but if it is not:

• Turn heater ON
• Navigate to the ‘Connection’ function under Settings Service

Care and Cleaning

• The heater requires regular cleaning to ensure trouble-free operation
• Unplug the heater from the mains supply before cleaning
• Ensure that the heater has been allowed to cool down completely before cleaning
• The common cause of overheating is deposits of dust or fluff in the appliance
• Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills
• Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt
• Never use solutions such as petrol, thinners, or polishing agents
• Ensure the heater is dry before plugging back into the mains supply

ERROR MESSAGES

• Temperature sensor malfunction. Contact customer services.
• Short circuit on temperature sensor channel. Contact customer services.
• Overheating of temperature sensor (exceeded +48 degrees). Turn off the heater to allow it to cool down.
• The ambient temperature has dropped too low (below 26 degrees). Turn off the heater to allow the ambient temperature to rise.

SAFETY DEVICES

• This appliance has three protection devices
• Tilt Switch this will automatically turn the appliance off if the appliance is not in the correct operating position
• Resettable Thermal Link this will automatically disconnect the power to the appliance at a pre-set overheat temperature After cooling down it will reset and power on again If this occurs, investigate what is causing the appliance to overheat
• Thermal Fuse disconnects the appliance permanently in case of overheating (It is nonresettable)

CAUTION: The appliance generates heat during use Precautions must be taken to prevent the risk of burns, scalds, fires, or other damage to persons.

CARE AND CLEANING

• The heater requires regular cleaning to ensure trouble-free operation
• Unplug the heater from the mains supply before cleaning
• Ensure that the heater has been allowed to cool down completely before cleaning
• The common cause of overheating is deposits of dust or fluff in the appliance
• Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents and grills
• Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt
• Never use solutions such as petrol, thinners, or polishing agents
• Ensure the heater is dry before plugging back into the mains supply
• Do not attempt to dismantle the heater
• There are no user-serviceable parts For service or repair, contact an authorized electrical service technician.

CONTACTS

• Model No: GPPH770
• Supply: 220-240VAC 50Hz
• Wattage: 1350-1500w
• CLASS I
• Approval: GMA-509266-EA
• QC Passed: PO#-WwYY
• MADE IN CHINA

CUSTOMER SUPPORT

• NEW ZEALAND PH: 0800 232 633
• AUSTRALIA PH: 1300 465 3241300 465 324

PROOF OF PURCHASE

• To receive a warranty retain the receipt as proof of purchase

Three Year Warranty

Thank you for purchasing this Goldair Platinum product Your product is warranted against faults and manufactured when used innormal domestic use for a period of three years In nondomestic use Goldair limits the voluntary warranty to three months Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the warranty period This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone other than a qualified electrical service technician PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY The benefits given to you by this warranty are in addition to other rights and remedies available to you under the law in relation to the goods or services to which this warranty relates In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act 1993.

Goldair New Zealand

• CDB Goldair
• PO Box 100 707
• N.S.M.C
• Auckland
• Phone: +64 (0)9 917 4000
• Phone: 0800 232 633
• www.goldair.co.nz

Goldair Australia

• CDB Goldair Australia Pty
• PO Box 574
• South Morang
• Victoria, 3752
• Phone: +61 (0)3 9365 5100
• Phone: 1300 GOLDAIR (1300 465 324)
• www.goldair.com.au

Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.

References

• Goldair Australia
• Goldair Australia
• Gold Air
• Goldair Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>