Lechpol LUT0012-1 Lutownica Soldering Iron Owner’s Manual
- June 5, 2024
- Lechpol
Table of Contents
Owner’s manual
Soldering iron
Application:
Soldering iron is intended for indoor use; for soldering and desoldering small
components and electronic parts.
Safety instructions:
Please read this operation instruction carefully before use, and keep it for future reference.
- Before connecting the device to the power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
- Handle the soldering iron with care. The tip of the soldering iron reaches a high temperature and may cause a risk of fire and burns.
- The soldering iron tip may emit smoke during the first use, as the heating element dries out. This is normal and should last for a few minutes.
- Never file the specially-plated tip.
- When using non-resin-based solder, be sure to apply a solder paste to the part before applying the solder.
- Always disconnect from the power supply when not in use.
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
- Fixed power cable may only be replaced at an authorized service point.
- Do not attempt to repair this appliance yourself. Any repair can be carried out by an authorized service point exclusively.
- Always disconnect the product from the power mains before cleaning.
- Keep the device and its cable away from heat, water, moisture, sharp edges, and any other factor that may damage the appliance or its cord.
- Producer of this product is not responsible for damages caused by inappropriate handling and using the device.
How to solder:
-
File off any dirt, rust, or paint on the part you wish to solder.
-
Heat the part with the soldering iron. (fig.1)
-
Apply resin-based solder to the part and melt it with the soldering iron. (fig.2)
-
Wait for the solder to cool and harden before moving the soldered part. (fig.3)
Specification
| Model | Power supply | Power: (W) |
|---|---|---|
| LUT0012-1 | 220-240 V; 50 Hz | 30 |
| LUT0012-2 | 40 | |
| LUT0012-3 | 60 | |
| LUT0014 | 30 | |
| LUT0015 | 30 | |
| LUT0016 | 50 | |
| LUT0018-1 | 30 | |
| LUT0019-1 | 40 | |
| LUT0024-1 | 30 | |
| LUT0024-2 | 40 | |
| LUT0024-3 | 60 | |
| LUT0024-4 | 100 | |
| LUT0025 | 40 | |
| LUT0061 | 30/70 | |
| LUT0065 | 100 | |
| LUT0066 | 30/130 | |
| LUT0067 | 40 | |
| LUT0071 | 30/130 | |
| LUT0063 | 12V | 40 |
**** Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems) This marking is shown on the product or its literature,
indicating that it should not be disposed of with other household wastes at
the end of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this from other
types of waste and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their suppliers and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne.