Lechpol KOM1009-1 REBEL Led Desk Lamp User Manual
- October 31, 2023
- Lechpol
Table of Contents
Lechpol KOM1009-1 REBEL Led Desk Lamp
Product Usage Instructions
Safety Instructions
- Protect the device from water, humidity, and other liquids.
- Avoid using/storing it in extreme temperatures and direct sunlight.
- Keep the device away from open flames.
- Place the device on a stable surface.
- Avoid dropping the device or subjecting it to strong impacts.
- Use the device indoors only and in well-ventilated places.
- Avoid hanging any objects on the device.
- Do not cover the device with flammable objects.
- Avoid using the device in hot or humid environments.
- Do not leave the device unattended during servicing.
- Keep the device out of reach of children.
- Use the included USB cable for charging.
- Use only authorized accessories.
- Check the device for damage before each use.
- Do not attempt to repair the device yourself. Contact an authorized service point for check-up or repair.
- Disconnect the product from the power mains before cleaning.
- Clean the device with a soft, slightly damp cloth. Do not use chemical agents.
Battery Installation (LCD)
- Use a coin or similar object to turn the battery compartment cover anti-clockwise and remove it.
- Insert a CR2032 3V battery with correct polarization.
- Put the cover back in place and turn it clockwise until it locks.
Temperature
Press the touch button to adjust the temperature settings.
LCD Display Settings
- Press the SET button. When the hour starts to flash, use the UP/DOWN buttons to adjust.
- Press the SET button again to save and move on to minutes.
- Repeat the above steps to set the year, month, and day.
Time and Date Format
- Press the MODE button to enter alarm settings.
- Press the SET button. When the hour starts to flash, use the UP/DOWN buttons to adjust.
- Repeat the above steps to set the time format and temperature unit.
SAFETY INSTRUCTIONS
Please read this operation instruction carefully before use, and keep it for future reference. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.
- Protect this device from water, humidity and other liquids. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and other sources of heat.
- Do not use the device nearby open flames such as candles.
- Do not place the device on an unstable surface.
- Do not drop the device or subject it to strong impacts.
- The device is intended for indoor use only. Do not use outdoors!
- Do not use the device in poor-ventilated places.
- Do not hang any objects on the device.
- Do not cover the device with cloth, paper or other easily flammable objects.
- The performance of the sensor is reduced in hot environment (for example close to radiators) or in the vicinity of other sources of interference.
- Do not look directly into the light source. Risk of eye damage.
- Light panel may become hot during operation. Do not touch it!
- This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner for all the safety precautions being understood and followed. Children should be supervised to ensure that they do not play with the appliance. Children should not perform cleaning and servicing of the device unsupervised.
- Keep the device out of the reach of children.
- Use only the included USB cable to charge the device.
- Use only authorized accessories.
- Check the device for damaged prior to each use.
- Do not use this device if it has been damaged.
- Do not attempt to repair this appliance yourself. In case of damage, contact authorized service point for check-up or repair.
- Always disconnect the product from the power mains before cleaning.
- Clean this device with a soft, slightly damp cloth. Do not use any chemical agents to clean this device.
PRODUCT DESCRIPTION
- Light source
- LCD display
- Touch dimmer
- Stand
- Charging port
- Temperature sensor
- Battery compartment (LCD)
- DOWN button
- UP button
- SET button
- MODE button
- Temperature
- Date
- Day of the week
- Time and alarm
BATTERY INSTALLATION
BATTERY INSTALLATION (LCD)
LCD display memory is powered with one CR2032 3 V battery. Follow the below to install it correctly:
- Use a coin or other similar object and insert it into a notch on the battery compartment cover and turn it anti-clockwise. Remove the cover.
- Insert a CR2032 battery with correct polarization.
- Put the cover back on place and turn it clockwise until it locks in place.
Notes
- Use only specified batteries.
- Remove the battery from the battery compartment if the device is not going be used for a long period of time.
- Remove discharged battery from the battery compartment immediately as to avoid leakage.
OPERATION
Turning on/off
Connect the included USB-C cable to the lamp’s power port and the other end to the wall charger.
Press the touch button:
- once to turn on the device in 15% light mode.
- twice to enter 50% light mode
- three times to enter 100% light mode
- four time to turn off the device.
- hold for about 3 seconds to change the color temperature
LCD display settings
Time and date
- Press the SET button- when hour starts to flash, press the UP/DOWN buttons to adjust.
- Press the SET button again to save and move on to minutes.
- Repeat the above to set year, month and day.
Time format and temperature unit settings
- press the UP button to set time format (12/24 h)
- press the DOWN button to set temperature unit (°C/°F).
Alarm and snooze
- Press the MODE button to enter alarm settings.
- Press the SET button- when hour starts to flash, press the UP/DOWN buttons to adjust.
- Press the SET button again to save and move on to minutes.
- Press the SET button again to set snooze time (max. 60 minutes). Press the UP/DOWN buttons to adjust.
- Press the SET button again to set alarm sound. There are 8 different sounds to choose from. Press the UP/DOWN buttons to select desired one. Press the SET button to confirm and return to alarm settings screen.
- Press the UP button to turn on the alarm (alarm icon appears); press the UP button again to turn on snooze (snooze icon appears). Press the UP button for the third time to turn off alarm and snooze.
- Press the MODE button to return to the main screen.
- When the alarmrings, press any button to turn it off.
- Snooze is activated twice.
SPECIFICATION
- LCD display: time, alarm, snooze, date, day of the week, temperature
- 8 alarm sounds
- Touch on/off button with dimmer function
- Foldable construction
- Slim design
TECHNICAL DATA
- Light source: 25 pcs SMD2835
- Lamp data:
- Color temperature: 3000 K / 4000 K / 6000 K
- Luminous flux: 140 lm / 400 lm / 250 lm
- Power: 3 W / 7 W / 5 W
- Protection class: IP20
- Charging port: USB-C
- Power cable lenght: 1,2 m
- AC adapter:
- Input: AC 100 – 240 V ~ 50 / 60 Hz
- Output: 5 V, 1 A
- Weight: 860 g
- Dimensions: 516 x 95 x 73 mm
- In set: AC adapter, USB-C cable
LEARN MORE
- For more information on this device visit: www.rebelelectro.com.
- Read owner’s manual carefully before using your device.
- Visit www.rebelelectro.com website for more products and accessories.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400 Miętne.