HEMA 80080009 2400W Steam Iron Instruction Manual
- June 5, 2024
- Hema
Table of Contents
Instruction Manual
Instructions for steam
Iron 2400W
TECHNICAL DATA
Operating voltage: 220-240V ~ 50-60HzPower consumption: 2400W
SAFETY INSTRUCTION
Before use make sure to read all of the below instructions in order to avoid injury or damage, and to get the best results from the appliance. Make sure to keep this manual in a safe place. If you give or transfer this appliance to someone else make sure to also include this manual. In case of damage caused by the user failing to follow the instructions in this manual, the warranty will be void. The manufacturer/importer accepts no liability for damages caused by failure to follow the manual, negligent use, or use not in accordance with the requirements of this manual.
- This appliance can be used by children aged from8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
- The iron must not be left unattended while it is connected to the supply mains.
- Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down.
- The iron must be used and rested on a flat, stable surface.
- When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
- The filling aperture must not be opened during use.
- The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.
- The plug must be removed from the socket outlet before the water reservoir is filled with water.
- Before inserting the plug into the main socket, please check that the voltage and frequency comply with the specifications on the rating label.
- Disconnect the mains plug from the socket when the appliance is not in use and before cleaning.
- Ensure that the mains cable is not hung over sharp edges and keep it away from hot objects and open flames.
- Do not immerse the appliance or the mains plug in water or other liquids. There is a danger to life due to electric shock!
- To remove the plug from the plug socket, pull the plug. Do not pull the power cord.
- Do not touch the appliance if it falls into the water. Remove the plug from its socket, turn off the appliance and send it to an authorized service center for repair.
- Do not plug or unplug the appliance from the electrical outlet with a wet hand.
- Never attempt to open the housing of the appliance, or to repair the appliance yourself. This could cause electric shock.
- Never leave the appliance unattended during use.
- This appliance is not designed for commercial use.
- Do not use the appliance for other than intended use.
- Do not wind the cord around the appliance and do not bend it.
- The iron should always be off before plugging or unplugging from the wall socket.
- Never use the appliance if damaged in any way.
- When leaving, even when only for a short while, always unplug the iron.
- Burns can occur from touching hot metal parts, and hot water steam.
- . Use caution when you turn a steam iron upside down-there may be hot water in the reservoir.
- Always place the iron standing on a firm flat surface when interrupting ironing and after use.30. Keep the soleplate smooth. Avoid hard contact with a metal object.
- The cord should not be allowed to touch the soleplate when it is hot.
- Prevent water overflow. Do not over max level.
- When using the iron for the first time use it on an old piece of fabric to check if the soleplate and water from the water tank are completely clean.
- Remove the plug from the socket before filling or emptying the water reservoir.
- The iron shall be used on a stable ironing board.
- Regarding the instructions for cleaning and maintenance, please refer to the below paragraphs.
- WARNING!! Please do not touch surfaces while in use. The temperature of accessible surfaces may be high when the appliance is operating.
**PARTS IDENTIFICATION
**
- Temperature regulator
- A burst of steam button
- Spray button
- Spray nozzle
- Water inlet cover
- Indicator light
- Steam control knob
- Soleplate
- Water tank
- Self-clean button
- Power cord and plug
BEFORE INITIAL USAGE
Remove all packaging material. Make sure the appliance is unplugged and the
temperature regulator is set at position “OFF”.
Open the water inlet cover and fill water into the opening up to the max level
marked on the water tank. For this, use the measuring cup.
Insert the power plug into a designated outlet and set the temperature
regulator on the highest temperature setting. After the indicator light goes
off, set the steam control knob to your desired position and iron on an old
piece of cloth to remove possible residue. With first use, there can be a
slight odor or smoke, but this is harmless and only for a short duration. Make
sure there is adequate ventilation.
OPERATION
Before selecting the temperature, read the instruction manual for the iron or
the care advice on the tag of the clothing.
Note: If there is no care advice on the piece of clothing, then you
should begin ironing at the lowest temperature. With lower temperatures, there
will be less steam.
OFF | Off |
---|---|
● | Nylon |
●● | Wool, silk |
●●● MAX | Linen, cotton, highest temperature |
DRY IRONING
- Connect the iron to a suitable mains supply outlet.
- Ensure that the steam control knob is in position
- Select the setting on the temperature regulator.
- When the indicator light goes off, the required temperature is reached. The iron is ready for use.
- To turn off the iron, turn the temperature regulator counterclockwise to position “OFF”, set the iron upright, and pull out the power plug.
STEAM IRON
Fill the water tank, as described before initial usage.
Steam ironing can be used in the temperature ranges ●, ●●, ●●● MAX. For the
reliable functioning of the steam ironing, the water tank must be at least ¼
filled.
Spraying function: Press the spray button to moisten a spot to be ironed.
Water will come out of the spray nozzle.
Steam Function : Turn the steam control knob to the required position
after preheating the steam iron first, steam starts coming out from the holes
in the soleplate.
A burst of steam: Turn the temperature regulator to the position
“MAX”. The indicator light will go off when the required temperature is
reached. Then press the burst of a steam button. This function provides an
extra amount of steam to remove stubborn wrinkles. For optimal use, please
allow the appliance to have a rest of 3 – 5 seconds between each press.
“Burst of steam” can also be applied when holding the iron in a vertical
position, which is useful for removing creases from hanging clothes, curtains,
etc.
The iron surface just always kept in an upright position. To turn it off, turn
the temperature regulator counterclockwise to “OFF” and pull out the power
plug.
Turn the appliance upside down and carefully pour the remaining water out of
the water tank. Carefully shake the appliance.
Press the spray button to allow the possible remaining water to come out more
easily.
ANTI-DRIP FUNCTION
The appliance has an anti-drip system, designed to prevent water from escaping
from the soleplate when the iron is too cold.
ANTI-CALC FUNCTION
The water tank is designed with an anti-calc function to filter the hard water
and reduce the limescale.
SELF-CLEAN FUNCTION
You can use the self-clean function to remove scale and impurities. The self-
clean function should be used at least once per month. If the water is very
hard in your area, use the self-clean function every two weeks.
- Make sure the appliance is unplugged.
- Set the steam control knob to position
- Fill the water tank to the maximum level.
- Select the maximum ironing temperature.
- Put the plug in the wall socket.
- Unplug the iron when the temperature indicator light goes off.
- Hold the iron over the sink, press and hold the self-clean button and gently shake the iron to and fro. (Steam and boiling water will come out of the soleplate. Impurities and flakes (if any) will be flushed out).
- Release the self-clean button as soon as all water in the tank has been used up. Repeat the self-clean process if the iron still contains a lot of impurities.
CLEANING AND MAINTENANCE
- Before cleaning the iron ensure it is disconnected from the power supply and has completely cooled down.
- Deposits on the soleplate may be removed with a rough cloth soaked in a vinegar water solution.
- The casting may be wiped with a damp cloth and then polished with a dry one.
- Do not use abrasives on the soleplate.
- Keep the soleplate smooth. Avoid hard contact with metal objects.
AUTOMATIC SAFETY CUT-OUT
If the built-in thermostat becomes defective, the power supply is
automatically cut off in order to prevent overheating of the iron. If this
happens, contact an authorized electrician/ service center for repair or
replacement.
TIPS
Which type of water to use?
Your appliance has been designed to function with untreated tap water. If your
water is very hard, it’s possible to mix untreated tap water with store-bought
distilled or demineralized water in the following proportion: 50% tap water /
50% distilled water.
Which type of water is not to use?
The types of water listed below contain organic waste or mineral elements that
can cause spitting, brown staining, or leakage: water from clothes dryers,
scented or softened water, and water from air conditioners.
If problems occur?
Brown streaks come through the holes In the soleplate and stain the linen.|
You are using chemical descaling agents.| Do not add any descaling agents to
the water.
---|---|---
Fabric fibers have accumulated in the holes of the soleplate and are burning.|
Let the iron cool down and clean the soleplate with a sponge. Vacuum the holes
of the soleplate from time to time.
Your linen has not been rinsed sufficiently or you have ironed a new garment
before washing it.| Make sure that your laundry is rinsed sufficiently so as
to remove any deposits of soap or chemical products on new clothes.
The soleplate Is dirty or brown and can stain the linen.| You are ironing with
a too high temperature.| Let the iron cool down and clean the soleplate with a
sponge. Select the appropriate temperature.
The soleplate is scratched.| You have placed your iron flat on a metal rest-
plate or ironed over a zip.| Always set your iron on its heel in an upright
position.
Do not iron over zips.
Water drips from the holes in the soleplate.| The chosen temperature is too
low and does not allow for the formation of steam.| Position the thermostat to
the maximum temperature setting.
You are using steam while the iron Is not hot enough.| Walt until the control
light goes out.
You have stored the iron horizontally, without emptying it and without
switching off the steam function.| Empty the iron after each use, and store it
vertically.
RECYCLING
****This product bears the selective sorting symbol for waste electrical and
electronic equipment(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. For further information,
please contact your local or regional authorities.
Electronic products not included in the selective sorting process are
potentially dangerous for the environment and human health due to the presence
of hazardous substances.
QUALITY
Safety and quality are very important to HEMA. We have our own laboratory,
which assesses all equipment in terms of electrical safety and ease of use
before it is included in our range. HEMA also monitors the product quality in
collaboration with the manufacturer.
SECURITY
This HEMA item may be fitted with a plastic anti-theft strip. You will find
the strip on the bottom of the product. This strip does not influence the
quality or the operation of the product and can be removed without a problem.
FAULTS AND REPAIRS
If this device needs to be repaired, you can hand it in at a HEMA branch after
packing the product securely. Do not try to repair this product yourself. For
repairs that fall within the warranty period, you will need to show proof of
purchase and the warranty document. Regularly check the power cord for damage.
If there is any damage to the cord set, please return the item to a HEMA
branch for repair. Do not try to replace it yourself. For safety reasons, we
recommend that you do not carry out any repairs to an electrical device
yourself.
WARRANTY
The warranty period is 2 years from the date of purchase. Always keep your
receipt in a safe place. It’s handy if you take a picture of the receipt and
save it somewhere. Then you will always have an easy-to-read receipt in your
possession.
WARRANTY CONDITIONS
HEMA quality guarantee
HEMA guarantees that the product you have purchased meets the standards our
customers are entitled to expect in terms of quality and product properties.
These warranty conditions do not affect your statutory or consumer rights and
apply in all countries where there are HEMA branches.
Warranty claims
If you wish to make a warranty claim, please return the product with proof of
purchase to one of our stores. The store will determine whether to replace the
product (with an identical or equivalent product), accept the product for
repair within a reasonable period of time, or refund the price of the product.
Invalidation of warranty
The warranty on this article is invalidated if the fault or defect is caused
by:
- normal wear and tear
- external damage (for example, damage caused by exposure to sand or moisture or due to falling of the product, etc.)
- improper or inappropriate use
- overdue or incorrect maintenance, including repairs that were not authorized by HEMA
The above list does not exclude other possible reasons for defects not being covered by the warranty.
Added confidence when choosing a HEMA product
You may swap or return the product within 30 days after purchase (provided it
is undamaged and you have proof of purchase).
HEMA BV
PO Box 37110
1030 AC Amsterdam
The Netherlands
These warranty conditions apply without prejudice to the customer’s statutory
rights or any other claims by the customer.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>