argo Wallner OL290 Laminator Instruction Manual

OL290 Laminator
Instruction Manual

SAFETY INSTRUCTION MARKS

WARNING
HOT! May cause physical injury or harm. Keep off touching or direct collision on the body.

1. ON/OFF switch: It is to switch on or off the power supply
2. HOT/COLD switch: It is to choose cold or hot lamination
3. RED LED: Referring that the power is well connected; if the HOT/COLD switch is in the HOT position, it means the laminator is in the pre-heating process; if in the COLD position, it means the laminator is ready to laminate
4. GREEN LED: Ready for Hot lamination
5. RELEASE/REVERSE: Jam release button

**** ELECTRICAL APPLICATION

Apply for use only on proper electric power usage as indicated in the rating plate on the laminator. Keep on easy plugging and unplugging situations.
OPERATION PROCEDURES

1. It is normal that new laminator could smell irritated in beginning, please keep fluent air ventilation before using.
2. Place laminator on table leaving enough space for the laminated object to access and come out from the laminator smoothly.

HOT LAMINATION

1. HOT Lamination: Turn the switch to „HOT” and wait until the GREEN light is READY illuminates, which means warm-up is completed and the laminator is ready to use. To stabilize the thermal conditions and increase lamination quality, please wait a few minutes after the READY diode will light up before you start laminating the document. Normal papers or laminating pouches from 80 microns to 125 microns, can be proceeded on this stage.
2. We suggest turning the switch to OFF for 30 minutes and cooling the laminator after HOT lamination for 30 minutes, then start the new HOT lamination.
3. Press the switch to „OFF” and when not in use for safety precautions.

COLD LAMINATION

1. Cold lamination is at its best performance for cabinet temperatures less than 35°C(95°F); this machine will not generate heat on the cold lamination stage, please keep the machine temp under 35°C(95°F).
2. Use the cold lamination pouches only.
3. Cold lamination is for fax paper, light-sensitive photos, and other papers/documents that will be affected by heat.
4. Turn the switch to the „COLD” position then insert the papers into the cold lamination pouch then start the cold lamination.
5. If the cold lamination is after the „HOT” lamination, please turn the switch to „COLDcool the machine; and wait for 30 minutes then cold lamination could proceed.

JAM RELEASE BUTTON
Due to the situation of necessary termination during lamination or paper jam, keep pressing on the RELEASE / REVERSE button and pull out the laminated pouches at the same time, then start the new lamination.
IMPORTANT NOTES

1. Select the rightful size of lamination pouch to use as inadequacy to fully cover the laminating material can cause laminator jam or damage.
2. Not applicable for one-side lamination only.
3. Sensitive paper as fax paper or its similar material can only proceed with „COLD” lamination mode.
4. Do not laminate exceeding the maximum thickness of 0.5mm. Laminating pouch from 80-125 microns (3-6 mils.) can be used to laminate the standard DIN A4 70gsm paper but suggest using only the 80 microns pouch for laminating thicker papers or photos.
5. Regular maintenance of laminator rollers by use of specialized cleaning paper can lessen laminator jam occurrence.
6. When the laminated material happens to get stuck during the lamination process, and is unable to be pulled out by the RELEASE / REVERSE Button, avoid the dangerous attempt of trying to open or dismantle the machine by your own.
7. The machine does not require any maintenance or adjustment. Please do not attempt to take out the machine casing by yourself. If an unusual problem occurs, please contact our after-sales service centers for the proper repair.
8. The socket outlet shall be installed near the equipment and shall be easily accessible.
9. If wearing a tie or long necklace, use caution to keep these items away from opening.

DEFECTS
In case of any defects, laminating machine should be delivered to the seller or authorized service together with the warranty and damage description. Equipment should be secured with proper packaging (preferably the original carton box). The seller does not take responsibility for any consequences of transporting equipment not properly packed.

SAFETY INSTRUCTIONS:

1. Please, read the manual carefully.
2. Make sure that the electric cable does not interfere with usual office traffic.
3. When removing the cover, be careful to avoid electric shock.
4. Do not use the machine when it is wet.
5. Unplug the power supply, when equipment is not in use.
6. Do not cover the ventilation duct when equipment is in use.
7. Do not touch the ventilation duct when the equipment is in use.
8. Do not insert any objects into the ventilation duct.
9. Before lamination please check if the plug or the electric cable are not damaged.
10. Do not laminate close to flammable substances.
11. Do not use force during the process of lamination.
12. Documents with sharp edges and unproper thickness can damage rollers.
13. Warning! Documents may be very hot right after the process of lamination. Wait till they cool off.
14. Do not use canned air on the shredder. Never use aerosol, petroleum-based or other flammable products on or near the shredder.
15. When, according to the temperature limits in point 4.5.4 of the EN 60950-1:2006 norm, the risk of burning due to overpassing those limits appears, on the machine’s casing is placed a warning: UWAGA! GORĄCA POWIERZCHNIA NIE DOTYKAĆ or symbol ****

SPECIFICATIONS

NOTE ON ENVIRONMENTAL PROTECTION:
After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials, or other forms of utilizing old devices, you are making an important contribution to protecting our environment. RoHS

** 80-393 GDAŃSK
ul. Krynicki 1
tel.: 58 55 43 555
fax: 58 55 43 500
ODDZIAŁ:
02 – 784 WARSZAWA**
ul. Janowskiego 9
tel.: 22 648 03 48..49
fax: 22 648 03 50

References

• Argo - Lider rynku w zakresie laminowania, bindowania, oprawy dokumentów, niszczarek, gilotyn, identyfikacji, kart plastikowych

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>