Taylor Pneumatic Tool Company T-7892N 14 Heavy Duty Riveter User Manual

June 5, 2024
Taylor Pneumatic Tool Company

Taylor Pneumatic Tool Company T-7892N 14 Heavy Duty Riveter
logo

Taylor Pneumatic Tool Company T-7892N 14 Heavy Duty Riveter

OILING INSTRUCTIONS

  • OIL AFTER EACH USE WITH A FEW DROPS OF AIR TOOL OIL THROUGH THE AIR INLET.
  • RUN FOR ONE SECOND.
  • COAT ALL INTERNAL PARTS.

OPERATING INSTRUCTIONS FOR THE T-7892N RIVET TOOL RED

  1. Maintain fluid levels use 30 wt. non-detergent oil. Mount tool in vice with bottom cap #35 up. Remove #35 with wrench #55.
  2. Remove entire piston part #29, 31, 32, 33 as an assembly, by grasping #33 with a pair of pliers and pulling straight up.
  3. After the piston is removed, fill with 30 weight non detergent oil to 1/2 below #40 nut no oil should be in the #39 cylinder.
  4. Lightly grease #31 and#34.
  5. Replace piston and #35 cap, and remove tool from the vice.
  6. Now the tool is ready for use.
  7. The total amount of oil should be about 2-1/2 tablespoons.
  8. A few drops of 30 wt oil or air tool oil through the air inlet every 10 to 15 minutes is recommended if no air line oiler is in place.
  9. Adjusting the stroke.
  10. Remove #02 by using #55 wrench.
  11. For maximum stroke, loosen nut #08 and thread the nut all the way onto #17 piston.
  12. Then loosen #03 and #07 and thread them all the way to #08.
  13. Hold #08 with a wrench and tighten #3.
  14. For a shorter stroke, adjust #08 so that it is away from the shoulder of #17 by two or more threads, depending on how short you want the stroke to be.
  15. Always use the correct size nosepiece for the rivet you are using.
  16. It is a good idea to use a silicone oil such as WD-40 to lubricate the jaws(#04) when pulling quantities of rivets, as there may be a build up of metal particles that could cause mandrels to stick in the jaws.
  17. Air pressure the maximum pressure should be 90 PSI.
  18. A higher pressure could cause damage to your tool. Using the lowest pressure possible for your application will extend the life of your tool dramatically.
  19. As with all tools, make sure that all parts are tight from time to time, as vibration from use may loosen components.
  20. Mandrels – The T-7892N comes complete with the #22 mandrel catcher.
  21. Once a rivet has been popped and the next rivet is mounted in the nosepiece, the last mandrel will slide into the #22. To remove mandrels, turn the tool upside down and they will fall out of the slot in #22, or remove #22 completely and empty.

USE 90 PSI MAXIMUM

Ref #

1A

1B

1C

1D

1E

1F

2

3

3A

4

4A

5

5A

6

6A

7

8

9

10

11

12

15

16

17

18

19

20

21

22

| Part #

789201AN3

789201BN3

789201CN3

789201DN3

789201EN3

789201FN3

789202N3

789203N3

789203AN3

789204N

789204AN3

789205N3

789205AN3

789206N3

789206AN3

789207N3

789208N

789209N3

789210N3

789211N

789212N

789215N3

789216N3

789217N3

789218N

789219N

789220N3

789221N3

789222N3

| Description

1/4 Nosepiece 7/32 Nosepiece 3/16 Nosepiece 5/32 Nosepiece 1/8 Nosepiece 3/32 Nosepiece Frame Head

Jaw Case (for 1/4 7/32, 3/16) Jaw Case for 5/32, 1/8, 3/32) Jaws for 1/4 7/32, 3/16 Jaws (for 5/32, 1/8, 3/32

Jaw Pusher (for 1/4, 7/32 3/16”) Jaw Pusher for 5/32”, 1/8, 3/32 Jaw Case Spring

Jaw Case Spring Jaw Case Back Case Lock Nut Valve Cap O Ring Valve Spring Back Up Ring

O-Ring Frame Valve

Oil Piston O-Ring

Back Up Ring

Return Spring Small Frame Cap

Catcher

| Qty.

1

1

1

1

1

1

1

1

1

1set of 2

1set of 2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

---|---|---|---

Ref #

23

24

25

26

27

29

31

32

33

34

35

36

37

38

39

40

42

43

45

47

48

50

51

52

53

54

55

58

60

| Part #

789223N3

789224N3

789225N3

789226N3

789227N3

789229N3

789231N3

789232N3

789233N3

789234N

789235N3

789236N3

789237N3

789238N3

789239N3

789240N3

789242N3

789243N3

789245N

789247N3

789248N3

789250N3

789251N3

789252N3

789253N3

789254N3

789255N3

789258N3

789260N3

| Description

Hanging Clip O-Ring Spring

Valve Seat

Return Spring (Large) Air Piston Rod

O-Ring

Air Piston Ring Lock Nut

O-Ring Cylinder Cap Trigger Rod Trigger Lever Valve Pusher Air Cylinder

Frame Lock Nut Valve Cap Rubber Cushion Washer Ring

Frame Cap O-Ring Catcher Nut

Lever Pin Pin

Pin Trigger Wrench Wrench Pin

O-Ring

| Qty.

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

1

---|---|---|---

FOR WARRANTY INFORMATION & WARRANTY REGISTRATION
VISIT: www.taylorpneumatic.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Taylor Pneumatic Tool Company User Manuals

Related Manuals