Taylor Pneumatic Tool Company T-8030G Belt Sander Instruction Manual
- June 10, 2024
- Taylor Pneumatic Tool Company
Table of Contents
T-8030G
Belt Sander
1-3/16” X 21 1/4”
Uses Sanding or Surface Prep Belts
T-8030G Belt Sander
OILING INSTRUCTIONS: OIL AFTER EACH USE WITH FEW DROPS OF AIRTOOL OIL THROUGH THE AIR INLET. RUN FOR ONE SECOND TO COAT ALL INTERNAL PARTS
USE 90 PSI MAXIMUM
Ref # | Part # | Description | Qty. |
---|---|---|---|
1 | 8030G01 | Throttle Lever | 1 |
2 | 8030G02 | Lever Pin | 1 |
3 | 8030G03 | Motor Housing | 1 |
4 | 8030G04 | O-Ring | 1 |
5 | 8030G05 | Valve Stem | 1 |
6 | 8030G06 | O-Ring | 1 |
8 | 8030G08 | Regulator | 1 |
12 | 8030G12 | Lock Nut | 1 |
13 | 8030G13 | O-Ring | 1 |
14 | 8030G14 | Housing | 1 |
15 | 8030G15 | O-Ring | 1 |
16 | 8030G16 | Bearing | 1 |
17 | 8030G17 | Front End Plate | 1 |
18 | 8030G18 | Spacer | 1 |
19 | 8030G19 | Key | 1 |
20 | 8030G20 | Rotor | 1 |
21 | 8030G21 | Rotor Blade (set of 5) | 1set |
22 | 8030G22 | Cylinder | 1 |
23 | 8030G23 | Rear End Plate | 1 |
24 | 8030G24 | Bearing | 1 |
25 | 8030G25 | O-Ring | 1 |
26 | 8030G26 | Motor Nut | 1 |
27 | 8030G27 | Handle | 1 |
28 | 8030G28 | Cap Screw | 5 |
29 | 8030G29 | Handle Bracket | 1 |
30 | 8030G30 | Finger Plate | 1 |
31 | 8030G31 | Adjust Screw | 1 |
32 | 8030G32 | Guard Body | 1 |
33 | 8030G33 | Guard | 1 |
34 | 8030G34 | Roll Pin | 1 |
35 | 8030G34 | LockNut | 1 |
36 | 8030G36 | Washer | 1 |
37 | 8030G37 | Drive Pulley | 1 |
38 | 8030G38 | Dust Cover | 1 |
39 | 8030G39 | Cover Latch | 1 |
40 | 8030G40 | Cap Screw | 2 |
41 | 8030G41 | Stopper | 1 |
42 | 8030G42 | Spring | 1 |
43 | 8030G43 | Roll Pin | 1 |
44 | 8030G44 | Stopper Pin | 1 |
45 | 8030G45 | Tension Spring | 1 |
46 | 8030G46 | Tension Arm | 1 |
47 | 8030G47 | Bolt | 1 |
48 | 8030G48 | Idler Shaft | 1 |
49 | 8030G49 | Idler Pulley Assembly | 1 |
50 | 8030G50 | Collar | 1 |
51 | 8030G51 | Bearing | 2 |
52 | 8030G52 | Lock Nut | 1 |
53 | 8030G53 | Shoe | 1 |
54 | 8030G54 | Silencer | 1 |
55 | 8030G55 | O-Ring | 1 |
56 | 8030G56 | Air Deflector | 1 |
57 | 8030G57 | Air Inlet | 1 |
58 | 8030G58 | Sanding Belt | 1 |
59 | 8030G59 | Seal | 1 |
60 | 8030G60 | Valve Stem | 1 |
61 | 8030G61 | Spring | 1 |
62 | 8030G62 | O-Ring | 1 |
63 | 8030G63 | Snap Ring | 1 |
505 N. Railroad Ave. 33435
P.O. Box 1117 33425
Boynton Beach, Florida
For Warranty Information &
Warranty Registration Visit
www.taylorpneumatic.com
1022 TPTC /all rights reserved “
COPYRIGHT 2022/ final
Ph.561-732-1111
Fax561-731-4412
Toll Free800-805-8665
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>