Elatec TWN4 PALON COMPACT WALL Instruction Manual
- June 5, 2024
- ELATEC
Table of Contents
Elatec TWN4 PALON COMPACT WALL
INTRODUCTION
ABOUT THIS MANUAL
This user manual is intended for the user and enables a safe and appropriate
handling of the product. It gives a general overview, as well as important
technical data and safety information about the product. Before using the
product, the user should read and understand the content of this user manual.
For the sake of better understanding and readability, this user manual might
contain exemplary pictures, drawings and other illustrations. Depending on
your product configuration, these pictures might differ from the actual design
of your product.
The original version of this user manual has been written in English. Wherever
the user manual is available in another language, it is considered as a
translation of the original document for information purposes only. In case of
discrepancy, the original version in English will prevail.
SCOPE OF DELIVERY
COMPONENTS AND ACCESSORIES
Depending on your product configuration, the product can be delivered alone or
with different components and accessories, such as cables or wall holders, as
part of a kit. For more information about the delivered components and
accessories, refer to your delivery note, consult the ELATEC website or
contact ELATEC.
SOFTWARE
The product is delivered ex-works with a specific software version (firmware).
Refer to the label attached to the product to find the software version
installed ex-works.
ELASTIC SUPPORT
In case of any technical questions, refer to the ELATEC website
(www.elatec.com) or contact ELATEC technical support at support-
rfid@elatec.com
In case of questions regarding your product order, contact your Sales
representative or ELATEC customer service at
info-rfid@elatec.com
REVISION HISTORY
INTENDED USE
TWN4 Palon Compact Wall is a versatile in-wall mount reader for integration
into wall flush mount installation boxes. It supports enhanced interfaces,
especially RS-485, and inherits all advantages and integrated tool support of
the ELATEC TWN4 family. The IP54 protected housing is easy to install. The
standard electric frame design elements make a unique look and feel.
The product is for indoor use and may not be used outdoor.
Any use other than the intended use described in this section, as well as any
failure to comply with the safety information given in this document, is
considered improper use. ELATEC excludes any liability in case of improper use
or faulty product installation.
SAFETY INFORMATION
Unpacking and installation
-
The product contains sensitive electronic components that require particular attention when unpacking and handling the product. Unpack the product carefully and do not touch any sensitive components on the printed circuit board.
In case the product is equipped with a cable, do not twist or pull the cable. -
The product is an electronic product whose installation requires specific skills and expertise.
The installation of the product should be done by a trained and qualified personnel only.
Do not install the product by yourself.
Handling
-
Depending on your product configuration, the product might be equipped with one or more light-emitting diodes (LED).
Avoid direct eye contact with the blinking or steady light of the light- emitting diodes. -
The product has been designed for a use under specific conditions (refer to the product data sheet).
Any use of the product under different conditions might damage the product or alter its reading performance. -
The use of other RFID readers or reader modules in direct vicinity to the product, or in combination with the product might damage the product or alter its reading performance. In case of doubts, contact ELATEC for more information.
-
The user is liable for the use of spare parts or accessories other than the ones sold or recommended by ELATEC.
ELATEC excludes any liability for damages or injuries resulting from the use of spare parts or accessories other than the ones sold or recommended by ELATEC. -
Like most electronic devices, RFID systems generate electromagnetic waves that can vary in amplitude and frequency. It is generally known and accepted that some RFID devices might potentially interfere with personal medical devices, like pacemakers or hearing aids.
Users with a pacemaker or any other medical device should use TWN4 Palon Compact Wall carefully and refer to the information given by the manufacturer of their medical devices before using TWN4 Palon Compact Wall.
Maintenance and cleaning
-
Any repair or maintenance work should be done by a trained and qualified personnel only.
Do not try to repair or carry out any maintenance work on the product by yourself.
Do not allow any repair or maintenance work on the product by an unqualified or unauthorized third party. -
The product does not need any special cleaning. However, the housing may be carefully cleaned up with a soft, dry cloth and a non-aggressive or non-halogenated cleaning agent on the outer surface only.
Make sure that the used cloth and cleaning agent do not damage the product or its components (e.g. label(s)).
Disposal
- The product must be disposed of in accordance with the EU directive on waste electrical and electronic equipment (WEEE) or any applicable local regulations.
Product modifications
- The product has been designed, manufactured and certified as defined by ELATEC.
Any product modification without prior written approval from ELATEC is prohibited and considered improper use of the product. Unauthorized product modifications may also result in the loss of product certifications.
If you are unsure about any part of the safety information above, contact
ELATEC support.
Any failure to comply with the safety information given in this document is
considered improper use. ELATEC excludes any liability in case of improper use
or faulty product installation.
TECHNICAL DATA
Power supply
9.0 V – 30 V via connector X1; 4.3 V – 5.5 V via micro USB
Current consumption
Operating: typ. 160 mA @12 V; Idle: typ. 50 mA @12 V; Peak typ. 250 mA @12 V
Antennas
The reader is equipped with the following antennas:
HF antenna (13.56 MHz)
Dimensions: 39 x 42.5 mm / 1.54 x 1,67 inch
Number of turns: 3
LF antenna (125 kHz)
Dimensions: 27 x 27.5 mm / 1.06 x 1.08 inch
Number of turns: 179
BLE (2.4 GHz)
The antenna for the BLE module is integrated in the BLE chip.
For more information, refer to the related product data sheet or other
technical documents.
MODE OF OPERATION
The mode of operation described in the following chapter is based on a standard ELATEC RFID reader equipped with two LEDs. Depending on your product (number of LEDs, installed firmware, etc.) and in case the product settings have been modified with the AppBlaster tool, the information below might differ from your product configuration when in operation. In particular, the color and sequence of the LEDs on your product might be different.
-
OPERATING MODE
In order to start operating TWN4 Palon Compact Wall, it simply has to be connected directly to a host device. -
POWER UP
In case of an external power supply unit is used, the following requirements must be satisfied:- Limited power source according to the safety standards listed in the respective declaration(s) of conformity
- Short-circuit current < 8 A
Once TWN4 Palon Compact Wall is connected to the host device, it detects the type of communications cable (e.g. USB or RS-232), with which it is connected to the host.
In case of RS-232: Additionally, the RS-232 is sending a version string via RS-232 to the host device.
-
ENUMERATION
This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode, where both LEDs are turned off. -
INITIALIZATION
After powering up and enumeration (in USB mode), the device is turning on the built-in transponder reader logic. The green LED is turned on permanently. Some RFID readers need some kind of initialization, which is performed in this step. After successful initialization, the device sounds a short sequence, which consists of a lower tone followed by a higher tone. -
NORMAL OPERATION
As soon as the reader has completed the initialization, it is entering normal operation. During normal operation, the reader is searching for a transponder continuously. -
DETECTION OF A TRANSPONDER
If a transponder is detected by the reader, following actions are performed:- Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. An RS-232 device sends the ASCII code of an ID.
- Sound a beep.
- Turn off the green LED.
- Blink the red LED for two seconds.
- Turn on the green LED.
Within the two seconds timeout, where the red LED is blinking, the transponder, which just has been recognized will not be accepted again. This prevents the reader from sending identical IDs more than one time to the host. If during the two seconds timeout of the red LED a different transponder is detected, the complete sequence restarts immediately.
-
SUSPEND MODE
The USB version of the reader supports the USB suspend mode. If the USB host is signaling suspend via the USB bus, the reader is turning off most of its power consuming peripherals. During this operation mode, no detection of transponders is possible and all LEDs are turned off. Once the host is resuming to normal operation mode, this is also signaled via the USB bus. Therefore, the reader will resume to normal operation too.
COMPLIANCE STATEMENTS
EU
TWN4 Palon Compact Wall is in compliance with the EU directives and
regulations as listed in the respective declaration of conformity.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution
The Federal Communications Commission (FCC) warns the users that changes or
modifications to the unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC §15.105 (b)
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Contains FCC ID: WP5TWN4F10
Contains FCC ID: QOQ11
IC
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE COMPLIANCE
RF exposure statement (mobile and fixed devices)
This device complies with the RF exposure requirements for mobile and fixed
devices. However, the device shall be used in such a manner that the potential
for human contact during normal operation is minimized.
UNITED KINGDOM
TWN4 Palon Compact Wall complies with the requirements of the UK legislations
and other regulations as listed in the respective UK declaration of
conformity. The importer is responsible for applying the following information
to the packaging of the product:
- the importer company’s details, including the company’s name and a contact address in the United Kingdom.
- UKCA marking
FURTHER STATEMENTS
Should the device be certified and installed in the following countries or
regions, the corresponding statements (see below) must be contained in the
user manual.
APPENDIX
A – TERMS AND ABBREVIATIONS
| TERM | EXPLANATION |
|---|---|
| BLE | |
| --- | --- |
| FCC | |
| HF | |
| IC | |
| LED | |
| LF | |
| NFC | |
| PCB | |
| RFID | |
| UKCA |
B – RELEVANT DOCUMENTATION
ELATEC documentation
- ELATEC quick start guide
- Installation Manual TWN4 Palon Compact Wall kit
- TWN4 Palon Compact Wall data sheet
- TWN4 Palon technical handbook
Zeppelinstr. 1 • 82178 Puchheim • Germany
P +49 89 552 9961 0 • F +49 89 552 9961 129 • E-mail: info-rfid@elatec.com
elatec.com
Elatec reserves the right to change any information or data in this document
without prior notice. Elatec declines all responsibility for the use of this
product with any other specification but the one mentioned above. Any
additional requirement for a specific customer application has to be validated
by the customer himself at his own responsibility. Where application
information is given, it is only advisory and does not form part of the
specification. Disclaimer: All names used in this document are registered
trademarks of their respective owners.
© 2022 ELATEC GmbH – TWN4 Palon Compact Wall user manual DocRev2 – 02/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>