MY COFFEE SHOP Jura Impressa X9 Coffee Machine Instruction Manual

MY COFFEE SHOP Jura Impressa X9 Coffee Machine Instruction Manual

Cleaning Products – Jura Impressa XF50

Daily
See procedure – Daily milk system clean
Must be performed at the end of each day just before the machine is turned off
Purpose: To ensure the milk system is clean overnight so milk does not go off blocking the pathways

Use Cafetto daily milk cleaner 1 litre bottle (Prod no. 71144) or Jura Milk System Cleaner Mini Tabs 180g (Prod no. 71150)

Weekly
See procedure – Weekly milk system clean
Performed once per week
Purpose: To remove any build up of milk fats to ensure the milk frother works correctly

Use Cafetto weekly milk cleaner – 1 litre bottle (Prod no. 71145)

When prompted
Clean machine – See procedure (Coffee system clean)
Performed only when prompted (Every 220 coffees)
Purpose: Removes coffee oil from the brewing unit and coffee path to maintain the quality of the coffee

End of day cleaning

This procedure must be performed at the end of each day just before the machine is switched off. It is important the milk system is not used after the machine has been cleaned.

1. If you are using a milk cooler turn it off using the switch on the back of the cooler or the switch on the wall.

2. Remove the two tubes from the milk carton. Place the milk carton in your fridge overnight.

3. Wipe out the milk fridge with a damp cloth.

4. If the display shows CLEAN follow the instructions
   • CLEANING THE DUAL SPOUT Otherwise, follow the instructions
   • CLEANING THE MILK SYSTEM

5. Empty the drip tray and grounds bin.

6. Turn the coffee machine OFF at programming panel ON-OFF switch (A).

Note: If you are using a milk fridge, it should be left on 24 hours per day with the door closed. The milk can be kept in the fridge overnight.

Traditional steam arm:
After frothing milk wipe the steam arm with a damp cloth. Run the steam for 2 seconds to ensure the steam arm is clean. At the end of the day check the steam arm is clean before turning off.

Weekly milk system clean

Complete this procedure once a week after the daily milk system clean

Steps:

1. Remove the coffee spout cover by pressing the button down and pulling the cover back towards you. (Fig 1 – 2)
2. Remove the auto frother by pulling it back towards you while making small circular motions with your hand. (Fig 3)
3. Disconnect the flat and froth milk tubes from the auto frother. (Fig 4)
4. Separate the auto frother into 12 parts. (Fig 5)
5. Soak the parts in 300ml of warm water (not hot) and 15ml of Cafetto weekly cleaner for 20 min (max).
6. Remove the parts from the solution and rinse them under tap water.
7. Re-assemble the auto frother and reconnect the milk tubes.
8. Refit the auto frother ensuring the coffee spout and steam elbows on the auto frother line up with the outlets on the machine. Push the auto frother back against the face of the machine making small circular movements with your hand until the auto frother is right back against the machine.

Note: If milk is not flowing normally from the flat or froth outlets, refer to trouble shooting.

Cleaning procedures for the Jura X9

CLEANING THE MILK SYSTEM – This must be done at the end of each day This must be done at the end of each day

CLEANING THE DUAL SPOUT

CLEANING THE COFFEE SYSTEM

DECALCIFYING

Messages

Troubleshooting:

No milk Spluttering milk Not filling cups Froth milk is flat
Solution:

1. Make a café latte to see if the problem is on the left side (flat milk) or the right side (froth milk) or both sides.
   Note: Flat milk is poured first no the left side.

2. If the problem is on the right side (froth milk), remove the coffee spout cover by pressing the button down and pulling the
   cover back towards you. (Fig 1 – 2)

3. Replace the air suction (Fig 3). Test the milk system again by making another café latte. If the problem has been solved, order in a spare air suction (Part no. 71866) otherwise go to step 4.

4. Remove the coffee spout cover. Remove the auto frother by pulling it back towards you while making small circular motions with your hand. (Fig 4)

5. Disconnect the flat and froth milk tubes from the auto frother. (Fig 5)

6. Separate the auto frother into 10 parts. (Fig 6)

7. Soak the parts in 250ml of warm water and 15 ml of Cafetto red weekly cleaner (71145) for 30 min.

8. Remove the parts from the solution and rinse them under tap water.

9. Clean the milk, air and steam paths with the cleaning brush set (Part no. 71161, 71162, 71165). (Fig 7 – 13)

10. Re-assemble the auto frother and reconnect the milk tubes.

11. Refit the auto frother ensuring the coffee spout and steam elbows on the auto frother line up with the outlets on the
    machine. Push the auto frother back against the face of the machine making small circular movements with your hand
    until the auto frother is right back against the machine. (Fig 14)

12. Test the milk system. If the problem has not been resolved descale the machine and test again. If the problem has still
    not been solved call phone support on 1300 365 487.

Welcome to My Coffee Shop!
Our hours of operation are Monday – Friday 9am to 5pm. Visit us at your convenience at www.mycoffeeshop.com.au. Orders and service requests can be placed by:

Phone: 1300 365 487
E-mail: [email protected]
Online: www.mycoffeeshop.com.au
Remittances: [email protected]
Service enquiries: [email protected]

Next business day delivery via courier to:
Adelaide Canberra Melbourne Sydney for product orders placed by 1.30pm

Please note you will be advised when ordering if delivery charges apply to your order.

Once again, welcome to My Coffee Shop and remember we are here to help. If you have any questions please don’t hesitate to contact us.

We look forward to exceeding your expectations and making your day easier and more enjoyable.

Kind regards,
My Coffee Shop
Client Services
My Coffee Shop Pty Ltd

References

• Coffee Machines and Coffee Beans for Office and Home | My Coffee Shop

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>