HAVIT Lighting HV3592RGBW-WHT Halo RGBW LED Wall Light Instructions

: June 5, 2024
: Havit Lighting

Table of Contents

Product Specifications
Important Safety Issues:
Steps for Installation:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lighting HV3592RGBW-WHT Halo RGBW LED Wall Light
Instructions

Product Specifications

Halo

Material|

Aluminum

IP65

Input Voltage|

12v DC

ProtectionClass|

3 (Low Voltage)

LampBase|

Built-in LED

Lamp Wattage| 1x 7w| 1x12w| 1x18w| 1x24w
Colour Temp|

RGBW (Red, Green, Blue + 3000k)

Lumens| 250lm (3000k)| 300lm (3000k)| 350lm (3000k)| 400lm (3000k)
CRI|

80

Wiring|

Parallel

Dimmable|

Yes

Warranty|

3 Years Replacement*

HV3591 Dimensions	HV3592 Dimensi ons
HV3593 Dimensions	HV3594 Dimensions

Important Safety Issues:

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
All o-rings and seals must be in place correctly to maintain the warranty
This form may be updated at any time due to product improvements, please check the online installation form for the most current version.

Steps for Installation:

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen Allen screws on side of the fitting
Remove base plate from fitting
Install the base plate to the wall in the desired location using appropriate screws for application.
Seal all holes including cable entry hole and mounting screws.
Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
Connect the cable, Connect life then neutral wires.
Reattach fitting to base plate making sure Allen screws are tight to avoid water penetration
Apply silicon around the edge of the base to prevent any water from getting inside to electrical connections.
See APP Installation Instructions for connection to tablet or smartphone.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Must be installed by a licensed electrician

Contact Details:

143 Beauchamp Road
Matraville NSW 2036
Australia| Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
Warranty Terms & Conditions*| Additional Information
---|---
HAVIT Lighting HV3592RGBW WHT Halo RGBW LED Wall Light - qr
code |
https://havit.com.au/pages/warranty-terms-and-conditions| https://havit.com.au/

Steps for Connection to Smartphone or Tablet:

1. Download EASYLIGHTING App from APP Store or Scan QR Code
2. Change WIFI to Easy lighting
3. Open the APP on Smartphone or Tablet
4. Use a direct connection with WIFI Controller
5. Press Learn button on the receiver
6. Press Wheel on APP
7. Light will flash when pairing is Successful.| HAVIT Lighting HV3592RGBW
WHT Halo RGBW LED Wall Light - qr code2
---|---
Steps for Connection to Home Network:
1. Connect Controller to home network
2. Press I got it and then Yes
3. Select the WIFI you wish to connect to.
4. Enter Password
5. Close APP and Reopen
6. Controller will now be connected to Home Network

Controls for Smartphone or Tablet:

Main User Interface
to adjust colours and brightness| Music
Play music and Fitting will change with the beat| Tape
Change colours using the microphone
---|---|---
| |
Saved Modes
Change Colour with saved modes| Timers
Set timers for automatic on/off control| Shake
Shake phone to change colours
| |
| Dream Setting
When dream mode is active, LED
Strip can be set to individual settings
| Remote
Remote control settings

Must be installed by a licensed electrician

Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au