HAVIT Lighting HV3591RGBW-WHT Halo RGBW LED Wall Light Instructions

Halo Wall Light Installation Instructions

Product Specifications

Model No.| HV3591 RGBW-BLK| HV3591 RGBW-WHO| HV3592RGBW-BLK| HV3592RGBW-WHT| HV3593RGBW-BLK| HV3593RGBW-WHT| HV3594RGBW-BLK| HV3594RGBW-WHT
Name| Halo
Material| Aluminium
Colour| Black| White| Black| White| Black| White| Black| White
IP Rating| IP65
Input Voltage| 12v DC
Protection Class| 3 (Low Voltage)
Lamp Base| Built-in LED
Lamp Wattage| 1 x 7w| 1x12w| 1x18w| 1x24w
Colour Temp| RGBW (Red, Green, Blue + 3000k)
Lumens| 2501m (3000k)| 3001m (3000k)| 3501m (3000k)| 4001m (3000k)
CRI| > 80
Wiring| Parallel
Dimmable| Yes
Warranty| 3 Years Replacement*

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
• All o-rings and seals must be in place correctly to maintain warranty
• This form may be updated at any time due to product improvements, please check the online installation form for the most current version.

Steps for Installation:

1. Make sure that the electrical circuit is free of voltage (master switch off )
2. Loosen Allen screws on side of the fitting
3. Remove base plate from fitting
4. Install base plate to the wall in the desired location using appropriate screws for application.
5. Seal all holes including cable entry hole and mounting screws.
6. Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
7. Connect the cable, Connect life then neutral wires.
8. Reattach fitting to base plate making sure Allen screws are tight to avoid water penetration
9. Apply silicon around the edge of the base to prevent any water from getting inside to electrical connections.
10. See APP Installation Instructions for connection to tablet or smartphone.
11. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Connection to Smartphone or Tablet:

1. Download EASYLIGHTING App from APP Store or Scan QR Code
2. Change WIFI to Easylighting
3. Open APP on Smartphone or Tablet
4. Use a direct connection with WIFI Controller
5. Press Learn button on receiver
6. Press Wheel on APP
7. Light will flash when pairing is Successful.

http://download.appglobalmarket.com/happylightingdownload.html

Steps for Connection to Home Network:

1. Connect Controller to the home network
2. Press I got it and then Yes
3. Select WIFI you wish to connect to.
4. Enter Password
5. Close APP and Reopen
6. Controller will now be connected to Home Network

Controls for Smartphone or Tablet:

Main User Interface to adjust colors and brightness| Music
Play music and Fitting will change with the beat| Tape
Change colours using the microphone
---|---|---
| |
Saved Modes
Change Colour with saved modes| Saved Modes
Change Colour with saved modes| Shake
Shake phone to change colours
| |
Dream Setting
When dream mode is active, LED
The strip can be set to individual settings| Remote
Remote control settings
---|---
|

Must be installed by a licensed electrician

Contact Details:

143 Beauchamp Road Tel: 02 9381 8300
Matraville NSW 2036 Fax: 02 9666 8881
Australia Email: sales@havit.com.au
Web: www.havit.com.au
**Warranty Terms & Conditions*https://havit.com.au/pages/warranty-terms- and-conditions
Additional Information**https://havit.com.au/

References

• Havit Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>