matatalab VinciBot Coding Robot Set User Guide
- June 3, 2024
- matatalab
Table of Contents
Coding Robot Set
User Guide
VinciBot Coding Robot Set
Parts List
Turn on/off
Press and hold the Power button for 2 seconds to turn Vinci8ot on. The power
indicator turns on
Charging
To charge the battery, connect the US8-C cable to Vinci8ot and a computer or a
power adaptor.
Charge
VinciBot immediately when the battery is low.
Use a 5V/2A power adapter to charge the robot.
All functions of the robot are disabled while charging.
This toy is only to be connected to equipment bearing the following
symbol
Charging status
Play With Vinccibot
There are three modes preset: IR Remote Control mode, Line Following mode, and
Drawing mode. You can switch between them through the button on the remote
control. Start your coding journey with Vinci Bot now!
IR Remote Control mode
An IR remote control is included in the box with Vinci Bot. It can be used to
change the speed and direction of the robot or adjust the volume, etc. Operate
the robot on a smooth and flat playground.
Line Following mode
In Line Following mode, Vinci Bot moves automatically along the black lines on
the map.
Drawing mode
In Drawing mode, VinciBot draws a picture automatically.
Press
1,2,3 on the remote control to select a preset program. Press the robot
starts drawing.
Connect VinectBot
Vinci Bot supports block-based coding and text-based coding, allowing children
to easily learn coding from entry-level to advanced.
https://coding.matatalab.com
Method 1 Connect Vinci Bot to a computer via the USB-C cable
Method 2 Connect Vinci Bot to a computer via Bluetooth
For details, go to https://coding.matatalab.com and click Help
Product Overview
Specification
Bluetooth range | Within 10m (in an open area) |
---|---|
Recommended age group | Sand above |
Working time | >=4h |
Body shell | Environmentally-friendly ABS material, in line with ROHS |
Dimensions | 90x88x59mm |
Input voltage and current | SV,2A |
Battery capacity | 1500mAh |
Operating temperature | 0to 40€ |
Storage temperature | -10to+55°C |
Charging time [via5V/2Aadapter] | 2h |
Safety Instructions
- This product is not intended for use by children under the age of three.
- The power adapter (not included in the box) is not a toy. Keep it out of the reach of children.
- This product shall only be used with a transformer for toys
- Disconnect the product from the power supply before cleaning. Clean the product with a dry, fiber-free cloth.
- Children should play with the product under the guidance of an adult.
- ‘Falling even from a low height can damage the product.
- Never rebuild and/or modify this product to avoid malfunctioning.
- Do not use or charge the product in temperatures outside its operating range.
- If this product is not to be used for a long period of time, fully charge it before storage and recharge it at least once every three months.
- Use only a recommended power adapter (5V/2A) to charge the product.
- Regularly check whether the cable, plug, shell or other components are damaged. If damaged, stop using it immediately.
Caution
Risk of explosion if batteries are replaced by an incorrect type. Return the used batteries according to the relevant statutory regulations.
Support
Visit www.matatalab.com for more information, such as operating instructions, troubleshooting and software updates, etc.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications to this device not explicitly
approved by the manufacturer could void your authority to operate this
equipment. Note: This equipment has been tested and found to comply with the
limits for Class B digital devices, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1.6 W/kg averaging over one gram of tissue.
Device types VinciBot coding robot set (FCC ID: 2APCM-MTB2207) has also been
tested against this SAR limit. The highest SAR value reported under this
standard during product certification for use at the body is 0.155W/kg. This
device was tested for typical body-worn operations with the back of the
handset kept 0mm from the body.
To maintain compliance with FCC RF exposure requirements, use accessories that
maintain a 0mm separation distance between the user’s body and the back of the
handset. The use of belt clips, holsters, and similar accessories should not
contain metallic components in their assembly. The use of accessories that do
not satisfy these requirements may not comply with FCC RF exposure
requirements and should be avoided.
Hereby, MATATALAB CO., LTD. declares that the radio equipment type VinciBot is
in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet
address:www.matatalab.com/doc
** This device complies with the essential requirements and other relevant
provisions of the Low Voltage Directive 2014/35/EU, the EMC Directive
2014/30/EU, the Eco-Design Directive 2009/125/EC and the ROHS Directive
2011/65/EU.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT(WEEE)**
The WEEE marking indicates that this product should not be disposed of with
regular household waste at the end of its life cycle. This regulation is
created to prevent any possible harm to the environment or human health. This
product is developed and manufactured with high-quality materials and
components which can be recycled and/or reused. Please dispose of this product
at your local collection point or recycling center for electrical and
electronic waste. This will make sure that it will be recycled in an
environmentally friendly manner, and will help to protect the environment in
which we all live.
Warranty
- Warranty period: One (1) Year Limited
- The following circumstances will void the free warranty:
- Not able to provide this warranty certificate and valid invoice.
- This warranty is unilaterally modified or incompatible with the product.
- Natural consumption/wear and aging of consumable parts.
- Damage caused by lightning or other electrical system problems.
- Damage caused by improper use, such as external force, damage, etc.
- Damage caused by force majeure factors such as accidents/ disasters.
- Self-dismantled/ reassembled/ repaired products.
- The product exceeds the warranty period.
- Abuse or misuse, including but not solely limited to the failure to use this product beyond the user manual.
Caution-electric Toy
Not Recommended For Children Under 3 Years Of Ages. As With All Electric
Products, Precautions Should Be Observed During HandlingAnd Use To Prevent
Electric Shock. Conforms To The Requirements Of Astm Standard Consumer Safety
Specifications On Toy Safety F963.
WARNING
CHOKING HAZARD-small parts.
Not for children under 3 years.
This user guide contains important information, please keep it!