Harley Benton G112A-FR Active Cabinet User Manual
- June 4, 2024
- Harley Benton
Table of Contents
Harley Benton G112A-FR Active Cabinet
Quick start guide
This quick start guide contains important information on the safe operation of
the product. Read and follow the safety advice and instructions given. Retain
the quick start guide for future reference. If you pass the product on to
others please include this quick start guide.
Safety instructions
Intended use
This device is intended to amplify instrument signals with line level for
reproduction via loudspeaker boxes. Any other use or use under other operating
conditions is considered
to be improper and may result in personal injury or property damage. No
liability will be assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard! Ensure that
children do not detach any small parts from the product. They could swallow
the pieces and choke!
Where to use the product
Never use the product
- outdoors
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- next to a heat source or near an open fire
- at locations where the unit can become wet
- in places where the product is exposed to strong vibrations.
General handling
- To prevent damage, never use force when handling the product.
- Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Possible hearing damage
With loudspeakers connected, the device can produce volume levels that may
cause temporary or permanent hearing impairment. Do not operate the device
permanently at a high volume level. Decrease the volume level immediately if
you experience ringing in your ears or hearing impairment.
Danger of electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers. There are no user-serviceable parts inside. Do not use the
device if covers, protectors or optical components are missing or damaged.
Danger of electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a
protective contact plug. Do not modify the mains cable or the plug. Failure to
do so could result in electric shock/death or fire. If in doubt, seek advice
from a registered electrician.
Power supply
Before connecting the device, ensure that the input voltage (AC outlet)
matches the voltage rating of the device and that the AC outlet is protected
by a residual current circuit breaker. Failure to do so could result in damage
to the device and possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for
long periods of time to reduce the risk of electric shock or fire.
Possible damage due to installation of a wrong fuse
The use of different types of fuses can cause serious damage to the unit. Fire
hazard!
Only fuses of the same type may be used.
Possible staining
The plasticiser contained in the rubber feet of this product may possibly
react with the coating of your surface and after some time cause permanent
dark stains. In case of doubt, do not put the rubber feet directly on the
surface and use a suitable underlay if necessary, i.e. felt-pad floor
protectors or similar.
Features
- active full-range flat-response open-back box for modern digital guitar setups (amp modeling and multi effect processors)
- upright installation or as a tilt-back floor monitor
- lightweight Class-D technology
- controls for volume, resonance, and presence
- mute control with LED indicator
- LED indicators for signal and peak (L/R)
- wooden housing, with handle
Controls and connections
Front panel
- INPUT Input
- VOLUME Volume control
- RESONANCE Resonance control
- PRESENCE Presence control
- SIGNAL LED indicator for signal
- PEAK LED indicator for peak
- MUTE Button and LED for muting
- ON – POWER – OFF Main switch
- IEC chassis plug C14 with fuse holder
- LINE IN Line input
- GROUND Slide switch for grounding
- LINE OUT Line output
Rear panel
Technical specifications
- Speaker 1 × 12″ speaker 1 × 1″ compression driver
- Input connections 1 × 1/4″ jack socket 1 × XLR (balanced)
- Output connections 1 × XLR (balanced)
- Input impedance 20 kW (balanced) 10 kW (unbalanced)
- Input sensitivity Line 1 V (RMS) Input 200 mV (RMS)
- Output power LF 100 W (RMS) @ 8 W HF 10 W (RMS) @ 8 W
- Frequency response 100 Hz … 20 kHz, –15 dB Sound pressure level (SPL), max. 121 dB / 127 dB (Peak)
- Dispersion angle (H × V) 30 ° × 110 °
- Total harmonic distortion (THD) 0.5 %
- Wire connection PIN1: earth / PIN2: signal+ / PIN3: signal– PIN1: signal+ / PIN2: signal– / PIN3: earth
- Power consumption max. 100 W
- Power supply 230 V 50 Hz
- Fuse 5 mm × 20 mm, 2.5 A, 250 V, slow-blow
- Dimensions (W × H × D) 482 mm × 448 mm × 301 mm
- Weight 14.2 kg
- Ambient conditions Temperature range 0 °C … 40 °C Relative humidity 20 % … 80 % (non-condensing)
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • info@thomann.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>