Viking Stage Lighting VKIO24 DMX Replay User Manual

Viking Stage Lighting VKIO24 DMX Replay

Introduction

The Show Replay VK1024 is a versatile DMX tool. It can acts as a DMX recorder, signal booster, ArtNet to DMM signal converter, DMX merger.

Features

• Supports ArtNet and DMX
• 1024 channels DMX in & out
• Real-time record and replay via DMX or WiFi
• 14 Memories and each up to 20 hours can be stored in SD card
• The replay can run in solo or loop mode
• The replay can run on iPad/iPhone via TouchOSC
• Bridge modes:
  • DMX input to DMX output (signal booster)
  • DMX input to Arnent output via LAN
  • Artnet input via LAN to DMX output
  • Artnet input via WiFi to DMX output
  • Artnet input via Wifi to ArtNet out from LAN
  • DMX Merge (HTP/LTP/override/backup)

Product Overview

OPERATING INSTRUCTIONS

MENU Map

BRIDGE

Under BRIDGE, the unit works as a signal converter. Press the BRIDGE button and its LED is lit up. Then use MENU/ENTER/UP/DOWN to select different modes as below.

RECORD

Data of lighting show can be recorded from the Ethernet network, Wiri or 2 DMX inputs. tach memory can be stored up to 20 hours.

1. Press the RECORD button and its LED is lit up.
2. Use UP/DOWN to select record modes as below.
3. Press MEM 1 -MEM 14 button to select Memory for recording. The LED of the selected Memory is blinking and the corresponding number “MEMX(l -14)” will be shown on the LCD.
4. Press the button to start recording, to pause, and to end recording.

**MEMORY SET

**

Each MEMORY can be recorded in “over time” or “step by step” mode. Follow the following steps to set MEMORY type before recoding.

REPLAY

The replay can be in solo or loop mode. And replay can be operated on the unit or iPhone/iPad via T ouchOSC.

Replay on unit

1. Press the REPLAY button and its LED is lit up. The unit goes to last stage of replay.
2. Use and button to run in loop mode, a button to run in solo mode.
3. In loop mode, the LED indicator of (or ) is blinking. and the button indicates the direction of running. The LED indicators of selected memory are lit up and the blinking one is in running.
4. When in loop mode, press the button to pause, press the button again to enter solo mode and its LED is blinking. In solo mode, the selected MEM (memory) are lit up. Press the selected one to run in solo mode and its LED is blinking.
5. Use the SPEED knob to adjust the running speed from 25% to 200%. Use the DIMMER knob to adjust output from O to 100%.
   NOTE: MEM button without recording data can’t be selected in REPLAY.

Replay on a iPhone/iPad

In order to use an iPhone or iPad to control the RECORDER, you need to install T ouchOSC and upload the interface of RECORDER on your iPhone/iPad.

1. Download TouchOSC from Apple Stores and install it on your iPhone/iPad.
2. Click on OSC and run it on your iPhone/iPad.
3. Power on RECORDER.
4. Connect your iPhone/iPad with the RECORDER. Click WLAN setup on your iPhone/iPad and select OMX AIO xxx (xxx=000-999). Password is 12345678.
5. Download TouchOSCEditor.exe ( https://hexler.net/software/touchosc) and install it on your PC/laptop.
6. Run T ouchOSCEditor · click “Open” and select “W-RECORDERl 024. touches” file on your PC/laptop.
7. Click on the dot in the upper right corner of your iPhone/iPad, and then click LAYOUT and Add.
8. Click “Sync” on T ouchOSCEditor and the name of the PC/laptop will be shown on your iPhone/IPAD.
9. Click the name of PC/laptop on your iPhone/IPAD and confirm OK, then you will see the name in the layout list. Click and select it.
10. Click on OSC: 192.168.16.254 (IP of RECORDER) · and then set Port(outgoing): 6454 and Port(incoming): 8000 as figure below.
11. Click done and now your iPhone/IPAD will have the same interface as Recorder.

SPECIFICATIONS

• Default LAN IP address: 002.114.034.200
• Default WiFi IP address: 002.000.000.001
• OMX In: 2 x 3pin XLR male
• OMX Out: 2 x 3pin XLR female
• Power consumption: 6w max.
• Power In: AC 100-240V 50-60Hz
• Dimension: 48220044 mm
• Weight: 2.0 kg

Software updating

The software can be upgraded via SD card in the following steps:

1. Copy the new software (SSCR 10 AM & SSCR 1 OAS) to the root directory of the SD card.
2. Insert the SD card and press the Menu button till “SYSTEM setup [new software]” shows on display.
3. Press Enter button.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>