RUKKET SPORTS RBND700 Portable Adjustable Tennis Trainer Rebound Practice Net Instruction Manual
- June 4, 2024
- RUKKET SPORTS
Table of Contents
RUKKET REBOUNDER
RSSEMBL Y INSTRUCTIONS
Our video instructions provide the best guide for setting up your Rukket
Rebounder. They can be viewed online at
RukketSports
Please call us if you have any questions or concerns at 1-855-4RUKKET Please read our product safety warnings before setup
INCLUDED EQUIPMENT
| A. Bolts | J. Right Center Support Welded Pipe |
|---|---|
| B. Carriage Bolts | K. Net |
| C. Metal Stakes | L. Rip Cord |
| D. Upper Left Tube | M. Rear Support Tubes |
| E. Middle Upper Tube | N. Front Lower Support Tubes |
| F. Upper Right Tube | O. Allen Wrench |
| G. Metal Net Stretcher | P. Hex Wrench |
| H. Bungees | Q. Middle Lower Tubes |
| I. Left Center Support Welded Pipe | R. Rubber Anti-Slip Rings |
PRODUCT SAFETY WARNING
Keep hands and fingers clear of all moving parts.
When adjusting the angle of the rebounder, keep positive control of the top
crossbar so as not to drop it on your head or body.
Place the rebounder on a level, well-drained surface. Make sure to set the
rebounder up where, when a misses the rebounder or is missed by the player on
its return, the ball will not strike or cause damage to people, pets, or
structures.
Children should not operate the rebounder adjustment; adults should make
adjustments.
To prevent injury, children should not use the rebounder until adequately
instructed.
PRODUCT MAINTENANCE
- The plunger bolts should be periodically oiled to maintain proper function (oil not included).
- To prolong the life of the bungees, we suggest you store your rebounder indoors, as water and UV rays will damage the elastic material and make it less effective.
|
---|---
Join both tops, and sidebars to the top crossbar. The fatter, circular
receiving nut goes into the round hole and the outside-threaded bolt with the
squared neck under the head goes into the square hole. Once you’ve threaded
the bolt into the nut correctly, seat the square bolt neck into the square
cut-out in order to tighten the nut with the hex key.
NOTE: The circular holes always face the inside of the frame. The square
holes are always on the outside.
NOTE: You may find it easier to join the carriage bolts together inside
the bars by hand-tightening them before seating the square neck of the bolt
into the bar’s square cut-out and tightening with the hex key.| Attach the
middle bars with angle-adjustment plates to the top assembly. The adjustment
plates should be near the top of the rebounder and the support bar that moves
along the plate should be on the inside of the rebounder.
|
Screw the plunger bolts into the welded-on nut and tighten down. Pull the cord
to disengage the plunger and release it to allow the plunger to engage one of
the holes. Set both of the rear support middle bars at the same setting so
that they are both at the same angle.| Attach the front legs with the silicone
traction pads to one of the bottom crossbars (both bottom crossbars have
silicone traction pads).
NOTE: The front legs are slightly shorter than the rear support legs.
Place them next to each other to identify which are the front and which are
the rear.
|
Attach the lower front assembly to the middle bars to complete the front of
the rebounder.| Attach the two lower legs with silicone traction pads to the
remaining bottom crossbar to make the rear support assembly.
|
Attach the rear support assembly to the rear support middle bars. When the
frame is securely bolted together, stand it up.| Attach the bungees to the
thick woven edge of the netting by using a girth hitch. Hitch 2 bungees in
each of the 4 corners of the netting. These 8 bungees will stretch the netting
up and down and side-to-side. The bungees should not cross each other.
|
Hang the netting bypassing the top crossbar bungees over the upper crossbar
and hooking them back onto the thick woven edge of the netting.| Hook the two
bottom lower crossbar bungees around the lower crossbar to stretch the netting
up and down.
|
Stretch the netting side-to-side by hooking the 4 remaining corner bungees
around the sidebars.| Alternate adding the remaining bungees between the top,
bottom, left, and right
to ensure that the netting is stretched evenly. We suggest using all of the
bungees, spaced 3 to 4 squares apart, to create maximum rebounding action. Use
the net expander by grabbing the thick woven edge with both hooks on the same
side of the intended bungee.
Please read our product safety warnings on page two before adjusting the rebounder.
|
---|---
|
QUESTIONS? GIVE US R CALL! [1-855]-478-5538
Documents / Resources
|
RUKKET SPORTS RBND700 Portable Adjustable Tennis Trainer Rebound Practice
Net
[pdf] Instruction Manual
RBND700, Portable Adjustable Tennis Trainer Rebound Practice NetTennis Trainer
Rebound Practice Net, Rebound Practice Net, RBND700, Practice Net
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>