Philips CoolPlay KH402 Wireless kid’s Headphones [TAKH402] User Manual

: June 2, 2024
: Philips

Philips logo

Headphone

User manual

Register your product and get support atwww.philips.com/support

1 Important safety instructions

Hearing Safety

Danger
To avoid hearing damage. limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.
Be sure to observe the following guidelines when using your headset.

Listen at reasonable volumes for reasonable periods of time.
Be careful not to adjust the volume continuously upwards as your hearing adapts.
Do not turn up the volume so high that you can’t hear what’s around you.
You should use caution or temporarily discontinue use in potentially hazardous situations.
Excessive sound pressure from earphones and headphones can cause hearing loss.
Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information

To avoid damage or malfunction:

Do not expose headphones to excessive heat.
Do not drop your headphones.
Headphones shall not be exposed to dripping or splashing.
Do not allow your headphones to be submerged in water.
Do not use any cleaning agents containing alcohol. ammonia. benzene. or abrasives.
If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Danger of explosion If battery is Incorrectly replaced. Replace only with the same or equivalent type.

About operating and storage temperatures and humidity

Operate in a place where temperature is between 02C (322F) and 452C(1132F) (up to 90% relative humidity).
store in a place where temperature is between -252C (-132F) and 552C(1312F) (up to 50% relative humidity).
Battery Life may be shorter in high or low temperature conditions.

2 Your Bluetooth wireless headset

Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/welcome.
With this Philips wireless headset, you can:

enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music.

What’s in the box

Philips Wireless kid’s headphones (TAKH402)

USB charging cable (for charging only)

Quick start guide

Other devices

A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see ‘Technical data’ on page 8).

Overview of your Bluetooth wireless headphones

1 + Volume control button
2 Light mode control button
3 – Volume control button
4 Micro USB charging slot
5 On/o button
6 LED indicator
7 Microphone

3 Get started

Charge the battery

Note

Before you use your headset for the first time, charge the battery for 5 hours for optimum battery capacity and lifetime.
Use only the original USB charging cableto avoid any damage.
Finish your call before charging theheadphones, as connecting the headphones o.
You can operate the headphones normally during charging.

Connect the supplied USB charging cable to:

the micro USB charging slot on the headphones and;
the charger/USB port of a computer.
LED turns white during charging and turns o when the headphones is fully charged

Tip

Normally,a full charge takes 2 hours.

Pair the headphones with your mobile phone
Before you use the headphones with your mobile phone for the rst time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 8 devices in the memory. if you try to pair more than 8 devices,the earliest paired device is replaced by the new one.

Make sure that the heaphones are fully charged.
Press and hold for 2 seconds to turn the headphones on.
Make sure that the mobile phone is turned on and its Bluetooth feature is activated.
Pair the headphones with the mobile phone. For detailed information. refer to the user manual of your mobile phone.

The following example shows you how to pair the headphones with your mobile phone.

Activate the Bluetooth feature of your mobile phone, select Philips KH402.
Enter the headset password”0000” (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password.

4 Use your headphones

Connect the headphones to a Bluetooth device

Turn on your mobile
phone/Bluetooth device.
Press and hold for 3 seconds to turn the headphones on.
The blue light on.
The headphones are reconnected to the last connected mobile phone/Bluetooth device automatically. If the headphone can not connect to last device within 13s, enter pairing mode.

Tip

If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually.

Note

If the headphones fails to connect to any Bluetooth device within range in 5 minutes, it will power o automatically to save the battery life.

Manage your calls and music

On/o

Music control

Call control

Wear your headset

Adjust the headband to t your head.

Headphone

5 Technical data

Music time: 20 hours
Talk time: 20 hours
Standby time: 800 hours
Normal time for a full charge: 2 hours
Rechargeable lithium polymer battery (200 mAh)
Bluetooth 5.0,
support (Hands-Free Prole – HFP),
Bluetooth stereo supported
(Advanced Audio Distribution
Prole – A2DP; Audio Video Remote
Control Prole – AVRCP)
Frequency range: 2.402-2.480GHz
Transmitter power: < 4dBm
Operating range: Up to 10 meters (33 feet)
Digital echo & noise reduction for call clarity
Auto power o

Note

Specications are subject to change without notice.
Rechargeable batteries are only to be charged under adult supervision.

6 Notice

Declaration of conformity

Hereby, MMD Hong Kong Holding Limited declares that this product Is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c. philips.com.

Disposal of your old product and battery

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol on a product means that the product is covered by European Directive 2012/19/EU.

This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery

Note

Make sure the headphones are disconnected from the USB charging cable before removing the battery.

If there Is no collection/recycling system for electronic products in

your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
Compliance with EMF

This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
Environmental information
All unnecessary packaging has been omitted. We have tiled to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment

Trademarks

Bluetooth

The Bluetoothe word mark and logos are registered trademarks owned by Bluetooth SIG. Inc. and any use of such marks by MMD Hong Kong Holding Limited Is under license.

Notice of compliance

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may causeundesired operation.

FCC rules

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,
Consult the dealer or an experienced radio/TV technician for

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Compliance Statement:
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
ISED Compliance Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

7 Frequently asked questions

My Bluetooth headphones do not switch on.

The battery level is low. Charge the headphones.

I cannot pair my Bluetooth headphones with a mobile phone.
The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headphones.

Pairing does not work
Make sure the headphones are in pairing mode.

Follow the steps described In this user manual (see ‘Pair the headphones with your mobile phone” on page 4).
Make sure that the LED fight flashes blue and white alternately

The mobile phone cannot find the headphones.

The headphones may be connected to a previously paired Turn off the connected device or move it out of range.
Pairing may have been reset or the headphones have been previously paired with another device. Pair the headphones with the mobile phone again as described in the user manual (see Pair the headphones with your mobile phone” on page 4).

My Bluetooth headphones are connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the headphones.

The audio quality is poor and crackling noise can be heard.
The Bluetooth device is out of range. Reduce the distance between your headphones and Bluetooth device. or remove obstacles between them.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.

Make sure your mobile phone not only supports (mono) HFP but also supports A2DP (see ‘Technical data” on page 7 ).

I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward).

Make sure the Bluetooth audio source supports AVFICP (see Technical data on page 7).

For further support, visit www.philips. com/support.

Philips CoolPlay KH402 Wireless kid’s Headphones [TAKH402] User Manual – Optimized PDF
Philips CoolPlay KH402 Wireless kid’s Headphones [TAKH402] User Manual – Original PDF