BOSCH VG4-SFPSCKT Fiber Optic Media Converter User Guide

BOSCH VG4-SFPSCKT Fiber Optic Media Converter

Important Safety Instructions

Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operation.

1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners.
2. Do not install units near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.
3. Do not block any ventilation openings.
4. Do not use the unit near water or expose it to rain or moisture. Never spill liquid of any kind on the unit.
5. Unplug the unit during lightning storms or when unused for long periods.
6. Adjust only those controls specified in the operating instructions.
7. Do not overload outlets and extension cords, as this can cause fire or electrical shock.
8. Protect the plug and power cord from foot traffic or pinching, at electrical outlets, and its exit from the unit.
9. Operate the unit only from the type of power source indicated on the label.
10. Unless qualified, do not attempt to service a damaged unit yourself. Refer all servicing to qualified service personnel.
11. Use only replacement parts specified by the manufacturer.
12. Install per the manufacturer’s instructions under applicable local codes.
    • Use only attachments/accessories specified by the manufacturer. Equipment change or modification could void the user’s guarantee or authorization agreement.

• WARNING High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death.
• CAUTION! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury.
• CAUTION! Low risk: Indicates a potentially hazardous situation if not avoided, this could result in property damage or risk of damage to the unit.
• You can view and print the full version of this Installation Manual with Adobe Acrobat Reader. This user guide is the intellectual property of Bosch Security Systems; protected by copyright.

Installing the Fiber Optic Module

This guide provides instructions for installing the Bosch VG4-SFPSCKT Fiber Optic module into a VG4-A-PA1, VG4-A-PA2, VG4-A-PSU1, or a VG4-A-PSU2 AutoDome power supply box.

Description

• The VG4-SFPSCKT is a unique media converter module for use with VG4 series AutoDomes incorporating the Ethernet (TCP/IP) Communications Module.
• This media converter module is designed to accept any of the 10/100 Mbps Small Form-factor Pluggable (SFP) modules described below.
• The media converter module along with the SFP module is user-installed directly into the AutoDome’s power supply box to provide an integrated fiber optic solution.

The Fiber Optic module accepts the following SFP modules:

• NOTICE! The SFP module is not included with the VG4-SFPSCKT kit, it must be purchased separately.

Using an SFP Module

• The SFP-23/SFP-24 modules and the SFP-25/SFP-26 modules are counterparts; if you use one in the VG4-SFPSCKT module then you must use the other in the CNFE2MC head-end unit.
• For example, SFP-25 is used in the VG4-SFPSCKT module installed into a VG4 power supply. You must use the SFP-26 module in the CNFE2MC head-end unit.

The following chart lists the compatibility between the SFP modules:

SFP Sub-module used in VG4- SFPSCKT| Use this SFP Sub-module in CNFE2MC
---|---
SFP-2| SFP-2
SFP-3| SFP-3
SFP-23| SFP-24
SFP-24| SFP-23
SFP-25| SFP-26
SFP-26| SFP-25

Parts Included

Installation Instructions

Use the following instructions to install the VG4-SFPSCKT Fiber Optic module inside a VG4 Power Supply Box.

1. Unpack the fiber optic module kit, and remove the parts from the bag.
2. Turn off the power to the VG4 power supply box and remove the cover.
3. Remove the 6-pin connector from the P106 connector inside the power supply box, if present.
4. Insert one plastic standoff pin into the hole on the main power supply board, located to the left of the P107 (Heater) connector.
5. Connect the supplied power harness (black) to the J103 socket on the power supply board, located below the Heater connector.
6. Insert three standoff pins into the metal base plate as shown below.
7. Align the upper right hole in the base plate to the standoff pin attached to the power supply box and press the base plate onto the pin. Secure the base plate with the supplied screw in the lower left hole of the P105 connector.
8. Insert the SFP module into the VG4-SFPSCKT module: Note: The SFP module is static sensitive. Use static handling procedures when installing or removing the module.
   • a. Ensure that the bale-clasp on the SFP module is up.
   • b. Line up the SFP module with the port on the VG4-SFPSCKT module and slide it into the port until you hear the catches engage.
9. Remove the rubber plug from the SFP module.
10. Align the anchor holes on the fiber optic module to the standoff pins on the base plate and press the module onto the standoff pins until secure.
11. Attach the supplied power harness (black) to its connector on the fiber optic module.
12. Connect the RJ45 Ethernet patch cable (blue) to its socket on the fiber optic module. Then attach the other end to the female mating connector in the AutoDome pendant arm.
    • Note: If installing a Pipe or Roof mounted AutoDome, you will need to provide the appropriate length Ethernet cable with RJ45 connectors to reach between the AutoDome and the power supply box.
13. Route the appropriate fiber optic cable through the conduit hole on the power supply box.
14. Plug the fiber optic cable (LC or SC connector) into the SFP module inside the power supply unit.
15. Close and secure the power supply box when finished.
16. Restore the power to the power supply box.

Troubleshooting

• If Green LED is present, then Check power to CNFE2MC:
• If the Power LED is Green, then check the data link

| Invalid Fiber Link|

• Check fiber connection to VG4- SFPSCKT:
• If a Red LED is present, then the fiber link is missing.
• If the LED is Flashing Red, then Check the fiber connection to the CNFE2MC:
• If the Link/Act LED is not lit, then the fiber link is missing.

| |
Issue| Symptom| Resolution
---|---|---
No Video present| RJ-45 Connection| Check the PWR/Link on the VG4- SFPSCKT:

–       If the LED is slowly Flashing Red, then

Check all video connections from the VG4 AutoDome.

–       If the LED is rapidly Flashing Red, then

Check the RJ-45 connector on the VG4-SFPSCKT:

–       If the right LED (Green) is not lit, then no data is present at this RJ-45 connection.

–       If no LED is lit on the RJ-45 connector, then there is a fault with this connector, the RJ-45 cable, or the cable is not connected to the CNFE2MC.

Check the RJ-45 connector on the CNFE2MC:

–       If the right LED (Green) is not lit, then no data is present at this RJ-45 connection.

–       If no LED lit on the RJ-45 connector, then there is a fault with this connector, the RJ-45 cable, or the cable is not connected to the VG4-SFPSCKT.

Customer Support and Service

• If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions.

Service Centers USA Repair Center

• Telephone: 800-566-2283
• Fax: 800-366-1329
• E-mail: repair@us.bosch.com

Customer Service

• Telephone: 888-289-0096
• Fax: 585-223-9180
• E-mail: security.sales@us.bosch.com

Technical Support

• Telephone: 800-326-1450
• Fax: 585-223-3508 or 717-735-6560
• E-mail: technical.support@us.bosch.com

Canada

• Telephone: 514-738-2434
• Fax: 514-738-8480
• Europe, Middle East, Africa Region Repair Center
• Telephone: 31 (0) 76-5721500
• Fax: 31 (0) 76-5721413
• E-mail: RMADesk.STService@nl.bosch.com

Asia Region Repair Center

• Telephone: 65 63522776
• Fax: 65 63521776
• E-mail: rmahelpdesk@sg.bosch.com

Customer Service

• Telephone: 86 (0) 756 7633117 or
• 86 (0) 756 7633121
• Fax: 86 (0) 756 7631710
• E-mail: customer.service@cn.bosch.com

Warranty and more information

• For additional information and warranty queries, please contact your Bosch Security Systems representative or visit our website at www.boschsecurity.com.

Americas

• Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, Pennsylvania 17601 USA
• Telephone +1 888-289-0096 Fax +1 585-223-9180 Email: security.sales@us.bosch.com www.boschsecurity.us
• Europe, Middle East, Africa: Bosch Security Systems B.V.
• P.O. Box 80002 5600 JB Eindhoven,
• The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.com

Asia-Pacific:

• Bosch Security Systems Pte Ltd 38C Jalan Pemimpin Singapore 577180 Phone: +65 6319 3450 Fax: +65 6319 3499 apr.securitysystems@bosch.com www.boschsecurity.com
• © Bosch Security Systems, Inc. 2009; F.01U.134.924 | 1.0 | 2009.09; Data subject to change without notice.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>