ROVSUN 10Lx4 Cold Juice Dispenser User Manual

June 1, 2024
ROVSUN

ROVSUN logo ROVSUN 10Lx4 Cold Juice DispenserCOLD JUICE DISPENSER
USER MANUAL

10Lx4 Cold Juice Dispenser

ROVSUN 10Lx4 Cold Juice Dispenser - overview

1 Drip tray
2 Mixing Blade
3 Plastic tank
4 Handle
5 Stirrer support
6 Bowl gasket
7 Plastic pin
8 Evaporator
9 Spring
10 Draw Valve
11 O-ring
12 Plastic Nozzle
13 Drip tray steel cover
14 Drip tray
15 Power button
16 Mixing button
17 Condenser
18 Main fan
19 Compressor

Introduction of juice dispenser

Thanks for choosing and using ROVSUN Brand Juice dispenser machines.
To ensure that you can use normally and effectively, please pay attention to follows

  1. Before use the machine, please read the instruction first and master the operation methods.
  2. Please use it according to the performance defined on the voltage power and the relative supply power cable.
  3. Please pay attention to the directions for the materials, which will not influence the normal use.
  4. To Protect the customers health, please wash the juice dispenser

Part one: Purposes and Features

The ROVSUN brand cold juice dispenser is manufactured by us based on absorbing the technologies from home and abroad. It can make the various beverage s and juice to be delicious liquid cold usually, It is widely used in hotels, restaurants, entertainment venues, schools, fast food chains, etc.
WARNING:

  1. This machine is a cold drink dispenser.

  2. This machine should be used only for the purpose for which it was designed.
    Any other use is inappropriate and, therefore, dangerous. The manufacturer will not be held responsible for any damage caused by improper use.

  3. Basic safety rules:
    a. Do not touch the machine when hands or feet are wet.
    b. Do not allow the machine to be used by children or untrained persons.
    c. Do not leave the machine outside.
    d. Do not pull on the electrical cord when unplugging the machine.

Part two :Main technology parameters

| 2 tank| 3 tanks| 4 tanks
---|---|---|---
Capacity( L)| 10Lx2| 10Lx3| 10Lx4
Power supply| 110V/60Hz
Power (W)| 200| 270| 325
Coldbeverin Temp(c )ture| 7— 12°C (44.6— 53.6°F)
Machine size ( mm)| 270x430x625| 400x430x625| 525x430x625
Net weight( kg)| 22| 26| 32
Refrigerants| R290

Part three :Installing Methods and Notices

  1. TO install it, lease choose the site which f lat, fixable and can avoid the direct sunshine in the summer.
  2. Around the juice dispenser, should have 15cm up room to make the air circulating and make sure the machine can run effectivel y.
  3. Before install it please check the supply power whether confirms to the requirements or not. The power supply cable is not too thin .The cross section of cable should be 1 .5-2 .5mm² , Voltage is between ( 110- 120V ) .To keep the users safety, it must have the reliable grounding. The socket should be mounted on the fixed position with fuse which will keep the machine running safely.

Part four: Using Methods

1. How to use the cold juice dispenser.

  1. To fall the prepared beverage into the tank, the height of the juice to the cover should be more than 70mm, otherwise, the beverage will flow out
  2. The temperature of the beverage filled in should not too high (no exceed 35℃ ), otherwise it will make a bad refrigeration.
  3. When the beverage become to the proper temperature, please make the cup against the push board lightly, the beverage will f low into the cup from the outlet mouth.
  4. When the temperature reduces to t he certain degree, the refrigerator will stop running because of the influence from the temperature cont roller. And when temperature increases, it will start work b automatic.
  5. It should restart after 5 minutes if it turn off suddenly to stop temporarily, otherwise, it will damage the compressor
  6. When work is over, first switch in the “ OFF ”position, then cutoff power supply.

Part five: cleaning

1 .In order to make the machine keep clean, health, beautiful, please wash the h oppers every day after work, the cleaning process usually less than 10minutes.

  1. Turn OFF power supply. Draw out all liquid mixture.
  2. Open the cover, gently rocking trough the hopper edge and upward to take the hopper down. (part number 3)
  3. After machine is cleaned ,please install all the parts back to the machine according to the method of disassembly, pay attention to the gasket i nstallation.(part number 6)

ROVSUN logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals