DOUBLEEAGLE INDUSTRY CHINA LIMITED SY-E511-003-07 Remote Control Car User Manual

June 1, 2024
DOUBLEEAGLE INDUSTRY CHINA LIMITED

DOUBLEEAGLE INDUSTRY CHINA LIMITED SY-E511-003-07 Remote Control Car

DOUBLEEAGLE INDUSTRY CHINA LIMITED SY-E511-003-07 Remote Control Car

Main Parameters

OPERA TING FREQUENCY 2405MHz-2475MHz
EIRP (MAX.) 472dBm

Item No. : E 511 -003
Material: plastic and electronic components
Batteries: Car battery : lpc of 4. SV AA rechargeable battery
Remote controller battery: 2pcs of 1. SV AA batteries

Main Parameters

Battery Inst山tion

  1. 0pen the battery cover of remote controller as the Fig 2A showed, inserts 2pcs of
    Battery Inst山tion

  2. SY AA batteries and then screws the cover.

  3. 0pen the cover under the truck by screwdriver’ inserts lpc of 4. SY AA rechargeable battery as the correct polarity, and then screw the cover. ( Fig 2B)
    Battery Inst山tion
    Battery Inst山tion

Notice: first charging requires 8 hours, future USB charge line requires 4 to 5 hours.

2.4G Auto Coding

  1. After installing the batteries of truck and remote controller, open the switch of both. The indicator of remote controller and the fronts lights of truck would be ,. flashing slowly, and then at a state of auto-coded.
    When the car with a sound of DI-DI, it means the auto-coding is successfully.

  2. 0ne remote controller only could code one car. After the success of coding, there is non-interference of each car.

  3. If the remote controller could not find out the 2.4G signal of the car in lminute, it would turn in a sleeping state(light off of the indicator). To press any key to activate.

  4. To remake a pair with other cars or remote controllers after turning off the power of both.

Basic Operation and Functions

  1. Forward/backward: To push the Left Trigger ahead/ back, the truck would go forward/backward; when forward, the lights on front and back would be lighted on; backward, the lights would be flashed (turn off when in a mute station) ( Fig 4B)
    2.4G Auto Coding
    2.4G Auto Coding

  2. Turn Left/Right: To push the Left Trigger forward/backward, and Right Trigger turns left/right, the truck would turn left/right. The lights on left would be flashed when turn left, the same of right lights when turn right. (Fig 4C)
    2.4G Auto Coding

  3. Excavating: press the key of “Excavating” after starting the car, the car will do a motion of excavating with sound. (Fig 4D)
    2.4G Auto Coding

  4. Unloading: press the key of ”Uoloading” after starting the car, excavator will do a motion of unloading with sound. (Fig 4D)

  5. Left/Right Rotation: press the key of “Left( or Right) Rotation” excavator will do a motion of left (or right) rotation, with a reminded sound of “Di- Di” the lamps of back also light up( Fig 4E ) These functions could be multiple used for simulating operation.
    2.4G Auto Coding

Advanced Functions

  1. Horn Button: after starting the car, press the Horn button on remote controller to emit a brilliance hom sound.
  2. Mute Function: press the Mute Switch Key on remote controller, the excavator could operate without sound. To press the key again to operate with sound.
  3. DEMO Function: To press the DEMO key, the car could operate a series of the functions automatically; to exit this function 出rough pressing any key
  4. Auto-OFF: after starting the excavator, the car will automatically shut down without receiving any controlling signal in 60 seconds.there is a sound of buffering about 1 second, and then all the functions are at a status of standby.

Recharging

Notice: Please tum the power switch to “OFF” position if the product will not be used for a long time Take the batteries out of the remote controller and the excavator if they are stored for a long time Charge the battery for about 4 to 5 hours, but it charges for 8 hours before initial use.

Notice

  1. Don’ t play the toy on the road, select a safe place for operating to avoid dangerous.
  2. Plays the toy in water may cause short circuit damage. Please use the dry cloth to clean the car.
  3. If abnormal speed or reaction, it may be because of insufficient battery power, please charge the battery.
  4. The batteries should be charged under adult supervision. Please use the batteries recommended.
  5. Please install the battery in a correct polarity.
  6. Do not mix new and old batteries together, short-circuited.
  7. Please charge the battery before initial use.
  8. Don t break the remote control antenna to prevent injurie.
  9. Please check the plug case and other units of charger regularly to make sure that it is not broken.Don’ t use again if you find abnormality of the charger.
  10. Please do not connect the product to different performance power.

CHOKING HAZARD-small parts, not for children under 3 years.
Specifications colors and contents may vary from illustrations.

Manu facturer. Dou bleeagle Industry (China) Limited.

Address: Xingda Industrial Pa「k, Chenghai District, Shantou City, Guangdong Province, China.
lmporter. JAMARA e.K.
Address: lnh . Manuel Natterer
Am Laueubuhl 5 – DE-88317 Aichstetten Germany

CHOKING HAZARD-small parts, not for child「en under 3 years

changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one Or more of the following measures:

  • * Reorient Or relocate the receiving antenna.
    • lnc「ease the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver ls connected.
    • Consult the dealer Or an experienced radio/TV technician for help.

MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device

Hereby, [DOUBLEEAGLE INDUSTRY (CHINAlLIMITED) declares that this [REMOTE CONTROL CAR SERIES] is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU..

Customer Support

The full test of the EU declaration of conformity is available at the following internet address:www.doublele-group.com.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals