Whirlpool WR619CHAUS 4 Zone Ceramic Cooktop User Manual

Whirlpool WR619CHAUS 4 Zone Ceramic Cooktop

Product Information

Specifications:

• Supply Voltage: 230-240V ~ + 220-240V 3 ~ + 380-415V 3N~ + 380-415V 2N~ +
• Conductors Amount x Size:
  • 3 x 2.5 mm2
  • 4 x 1.5 mm2
  • 5 x 1.5 mm2
  • 4 x 1.5 mm2

Product Description:

1. Radiant cooking zone 145 mm
2. Radiant cooking zone 210 mm
3. Radiant cooking zone 145 mm
4. Radiant cooking zone 180 mm

Product Usage Instructions

Placing the Hob:
Ensure the following dimensions and distances are maintained:

• Minimum distance to the sides: 5 cm
• Minimum distance to the rear wall: 40 cm
• Minimum distance to overhead surfaces: 10 cm
• Refer to the user manual for more detailed information.

Electrical Connection:
For electrical connection, use an H05RR-F or H05V2V2-F cable as specified in the table above. The appliance must be connected to the electricity supply using an all-pole disconnect switch with a minimum contact gap of 3 mm. Ensure the power supply cable is long enough to allow the cooktop to be removed from the worktop and positioned to avoid damage or overheating.

Removing the Hob:
To remove the hob, first disconnect it from the electric supply. Free the underneath part from any oven, drawer, separator, or other items to allow access to the lower part of the hob. Unfasten the four clips with a screwdriver, lift the hob, and remove it to avoid worktop damage.

FAQ:

Q: What should I do if the cooktop switches off automatically?
A: If the cooktop switches off due to reaching the maximum permitted temperature, wait for a few minutes until the internal temperature of the electronic circuits reaches a tolerable level. Then, you can switch the hob on again.

INSTALLATION

• The cooktop must be set into a worktop at least 20 mm deep.
• There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).
• Make sure the power cord is long enough to allow convenient installation.
• The distance between the lower face of the glass ceramic hob and the cupboard or separating panel must be at least 20 mm.
• For built-in dimensions and installation see the picture in this paragraph.
• A minimum distance must be maintained between the hob and the hood above it. Please refer to the user manual of the hood for more information.
• Apply the supplied gasket to the cooktop (unless it has already been fitted), after having cleaned its surface.
• Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam or moisture, which could damage them.
• If an oven is installed beneath the cooktop, make sure that it is equipped with a cooling system. If the temperature of the electronic circuits exceeds the maximum permitted temperature, the cooktop will switch off automatically; in this case, wait for a few minutes until the internal temperature of the electronic circuits reaches a tolerable level, at which point it will be possible to switch the hob on again.
• ATTENTION: to install the hob on other surfaces than wood (marble, plastic, ceramic, marble, stone, etc.) remember to ask After Sales Service for the fixing plates (fig. 2) Code 4819 404 78697.

PLACING THE HOB

• Important: remove any protective film before installing the hob.
• Make sure that the opening in the worktop for the hob is cut according to the dimensions given in the drawing, paying attention to the tolerance range.
• The hob should not be forced into the worktop. Forcing the glass ceramic top may cause it to crack (even at a later date)!
• If the worktop is made of wood, use the spring clips and screws provided. Secure the spring clips (A) (fig. 1) with the screws provided (B) (fig. 1) as shown, paying attention to the specified distances. Fit the hob into the worktop.
• If the worktop is made of marble, plastic, ceramic, stone, etc., the hob must be secured with special brackets (C) (fig. 2). Fit the hob into the worktop (fig. 1). Place the 4 brackets (C) in position by the thickness of the worktop as shown in fig. 2. Fasten the 4 screws (D) in the positions (E) (fig. 2).

DIMENSIONS AND DISTANCES TO BE MAINTAINED

REMOVING THE HOB:
To remove the hob, first, disconnect it from the electric supply. It is strongly recommended to free the underneath part from the oven, drawer, separator, or other. It allows the technician to access the lower part of the hob to unfasten the four clips with a screwdriver, lift the hob and remove it, avoiding any worktop damage.

ELECTRICAL CONNECTION

• An electrical connection must be made before connecting the appliance to the electricity supply.
• The power cord is not included in the package – remember to prepare your own power cord.
• Installation must be carried out by qualified personnel who know the current safety and installation regulations. Specifically, installation must be carried out in compliance with the regulations of the local electricity supply company.
• Make sure the voltage specified on the data plate located on the bottom of the appliance is the same as that of the home.
• Regulations require that the appliance be earthed: use conductors (including the earth conductor) of the appropriate size only.

CONNECTION TO THE TERMINAL BLOCK

For the electrical connection, use an H05RR-F or H05V2V2-F cable as specified in the table below.

The appliance must be connected to the electricity supply using an all-pole disconnect switch with a minimum contact gap of 3 mm.

ATTENTION:
The power supply cable must be long enough to allow the cooktop to be removed from the worktop and must be positioned so as to avoid damage or overheating caused by contact with the base.

NOTE:
The yellow/green earth wire must be connected to the terminal with the symbol and must be longer than the other wires.

• Remove approx. 70 mm of the cable sheath from the power supply cable (G).
• Strip approx. 10 mm of the sheath from the wires. Insert the cable (G) through the opening in the lid (F).
• Insert the cable into the cable clamp and connect the wires to the terminal block as indicated in the diagram printed on the lid.
• Secure the power supply cable (G) through the cable clamp.
• Refit the protection lid (F).
• After the electrical connection, fit the hob from the top and hook it to the support springs, according to the illustration.

PRODUCT DESCRIPTION

1. Radiant cooking zone 145 mm
2. Radiant cooking zone 210 mm
3. Radiant cooking zone 145 mm
4. Radiant cooking zone 180 mm
5. Rear right cooking zone control knob
6. The rear left cooking zone control knob
7. Front left cooking zone control knob
8. Front right cooking zone control knob

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>