TEFAL BL420840 Jug Blender with 2 Speeds Blend Force Instructions

TEFAL BL420840 Jug Blender with 2 Speeds Blend Force Instructions

depending on the model

DESCRIPTION

• Motor unit
• Speed control dial
• Blender:

C1 Blade support
C2 Blade
(*depending on model)
C3 Seal C4 Jug C5 Lid
C6 Measuring cap

• Spice mill

(* accessory depending on model)
C1 Blade support D1 Spice mill blade D2 Seal
D3 Spice mill bowl

• Herb chopper

(* accessory depending on model)
C1 Blade support
D2 Seal
E1 Herb chopper blade
E2 Herb chopper bowl

• Spatula

(* accessory depending on model)The accessories supplied with the model that you have purchased are shown on the label on the top of the packaging.
WARNING: Read the instructions for use carefully before using your appliance for the first time: the manufacturer shall accept no liability in the event of any use that does not comply with the instructions. Keep them in a safe place so that you can refer to them later.
The appliance can only operate when the jug (C) or the accessories
(D or E) are correctly positioned and locked on the motor unit (A).

• Before you use your appliance for the first time, clean all the accessories (C, D, E, F) using hot soapy water, except for the motor unit (A). WARNING: The blades are extremely sharp so handle them carefully when using and cleaning the
• Verify that the packaging has been removed before using the
• Important note: Turn the speed selector (B) to “0” before placing the blender jug or the accessories on the motor
• The appliance will only start if the jug or the accessory is correctly positioned and locked on the motor

WARNING: Do not use the blender if the lid is not in place.

Do not use the blender without ingredients or solid ingredients

Using the blender (C)

• Correctly position the seal (C3) on the blade (C2) (Fig. 1).
• Clip the blade (C2) on the blade support (C1) (Fig. 2)
• Place the blade assembly (C1, C2, C3) on the jug (C4) and lock it by turning the blade anti-clockwise (Fig. 3).
• Put the ingredients in the assembled jug without exceeding the maximum level indicated:

1.25 L for thick preparations

• 1 L for liquid preparations

Warning: Do not process boiling liquids (over 80ºC/176ºF) in the blender

jug.

• Lock the lid (C5) on the Place the measuring cap (C6) in the lid opening (Fig. 4).
• Place the assembled jug (C) on the motor unit (A). The open lock is aligned with the arrow on the jug (Fig. 5 – position 1).
• Then turn the blender jug (C4) a quarter turn until the closed lock is aligned with the arrow of the jug (Fig. 5 – position 2).
• Plug in the unit and turn it on by turning the speed selector to the desired position or apply a few To stop the blender, return to position 0.
• 2 positions are possible for the jug handle to the right or to the left of the motor
• Do not use the blender (C) continuously for more than three Wait a few minutes before switching it on again. Do not use one of the blender accessories (D, E) continuously for more than 30 seconds.

Using the herb chopper (E) or spice mill (D)

• The herb chopper (E) allows you to chop ingredients such as herbs, nuts, onions, garlic, and dried fruit in a few seconds and prepare
• Do not use the herb chopper (E) for processing hard spices or ice
• The spice mill (D) allows you to chop of spices in a few seconds: coriander seeds, peppercorns, coffee beans,
• Do not use the spice mill and the herb chopper for liquid preparations (fruit juice, )
• These accessories come with a bowl (D3, E2) which prevents access to the blades during
  1. Turn the bowl (D3, E2) upside down and add the
  2. Correctly position the seal (D2) on the blade (C1) (Fig. 5). Clip the blade (D1 or E1) to the blade support (C1) (Fig. 6).

Place the blade assembly (C1, D1 or C1, E2) on the bowl (D3 or E2) nd lock it by turning the blade clockwise (Fig. 7).

3. Turn over the assembled accessory (D or E) and position it on the motor unit. The open lock is aligned with the arrow on the bowl (Fig. 8 – position 1).
4. Then turn the assembled accessory (D or E) a quarter turn, anti- clockwise, until the closed lock is aligned with the arrow on the bowl (Fig. 8 – position 2).
5. Connect the appliance and turn the speed selector (B) to the desired position or pulse a few times. Hold the bowl (D3, E2) when the appliance is in operation. To turn off the appliance, turn the speed selector (B) to put it back to position “0”.
6. Unlock the accessory by turning it a quarter turn, anti-clockwise, until the closed lock is aligned with the arrow of the Remove the assembled accessory (D, E) from the motor unit.

Put it to the worktop before unlocking the blade (D1, E1) from the bowl (D3, E2) by reversing the order of assembly. The blades are very sharp: handle very carefully to avoid injury. You can then remove the preparation in the bowl.

• The colour of the bowl can change after the mixing of certain very hard ingredients (cloves, cinnamon, etc.).

  • Never immerse the motor unit (A) in water and never place it under under running
  • Unplug the appliance and remove the

• Handle them with care: the blades of the blender jug and the

accessories are sharp.

• Remove the jug (C) or bowl (D3 or E2) , then rinse it and its lid under running
• Clean the motor unit (A) with a damp Dry it carefully.
• To make cleaning easier, wash all removable parts with water and a little washing-up liquid immediately after
• To make it easy to clean the blender jug (C4) , unlock the blade (C2, D2, E2) by turning it a quarter-turn, anti-clockwise. It is possible to unclip the blade support (C1) to make cleaning easier. Remove the seal (C3) and clean the blade support and blade using running
• After cleaning, remember to correctly fit the seal (C3 or D2) back onto the blade Be careful to avoid any damage to the seal by the blades cutting it.

Note: Incorrectly fitting the seal can result in ingredients leaking from the blender jug, spice mill or herb chopper.

CLEANING THE JUG (PLASTIC, GLASS OR STEEL VERSION DEPENDING ON MODEL) IN

A DISHWASHER:

• The plastic, glass or steel jug (C4) , the the lid (C5) , the cap (C6), the spice mill bowl (E2) , the herb chopper bowl (D3) , as well as the spatula (F) can be cleaned in the upper basket of a dishwasher using the “ECO” or “REDUCED SALT” programme. The blades of the blender jug (C2), the seals (C3 & D2), spice mill (E1) and the herb chopper (D1) must not **be cleaned in a**

Problems

The appliance does not work.
Excessive vibrations.
There are leaks at the lid.
There are leaks at the base of the blender jug

Causes

The appliance is not properly plugged into the electrical outlet.
The jug or the accessory is not correctly positioned or locked on the motor unit.
The appliance is not placed on a flat, stable and heat- resistant surface.
The volume of ingredients is too big.
The volume of ingredients is too big.
The lid is not correctly positioned.
The seal of the blender jug (C3) is not correctly positioned or is missing.

Solutions

Plug the appliance into an electrical outlet and turn it on.
Check that the jug or the accessory is properlypositioned and locked in the motor unit as shown on the images of the Instructions for Use.
Place the appliance on a flat surface.
Reduce the quantity of ingredients in the appliance.
Reduce the quantity of ingredients in the appliance.
Lock the lid correctly on the blender jug.
Reposition the seal and lock the blade correctly (C2).
Contact an authorised repair centre (see the list provided in the documentation concerning the after-sales service).
You can customise your blender with the following accessories available from your usual distributor or an authorised service repair: Spice mill accessory (D) , herb chopper accessory (E) , additional blender jug (C4) , spatula (F).

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>