CROSSIO CFL-1153-01 20 Inch Crystal Ceiling Fan with Lights Installation Guide

June 1, 2024
CROSSIO

INSTALLATION
MANUAL
CEILING FAN WITH LIGHTS
Model No.: CFL-1153-01

CROSSIO CFL 20 Inch Crystal Ceiling Fan with Lights

CFL-1153-01 20 Inch Crystal Ceiling Fan with Lights

TOOLS REQUIRED

PACKING LIST

CROSSIO CFL 20 Inch Crystal Ceiling Fan with Lights - Parts
1

INSTALLATION KIT

CROSSIO CFL 20 Inch Crystal Ceiling Fan with Lights - Parts
2

NOTE:

  1. The crystals are fragile and spare parts are inclued.
  2. The listed quantity is for installation, extra hardware may be included.
  3. Mounting bracket (AA) and canopy screws (HH) are pre-installed on fan assembly (A).

INSTALLATION

  1. Install the Mounting Bracket
    Loosen and remove the canopy screws (HH) from the round holes, and loosen the canopy screws (HH) in the ‘L’ holes but do not remove them, and then remove the mounting bracket (AA) from the canopy. Step 1: Mark and drill screw holes in the ceiling, then insert the plastic anchors (FF).
    Step 2: Use outlet box screws (CC) and flat washers (DD) to fix the mounting bracket (AA) to the outlet box, and then tighten it with long wood screws (EE).

  2. Hang the Fan
    Hang the fixture onto the mounting bracket (AA) with “S” hook (GG) provided.CROSSIO CFL 20 Inch Crystal Ceiling Fan with Lights - Parts
5

  3. Connect the Wires
    Step 1: Connect the wires from the fan to the house supply wires with wire nuts (BB), ‘ground wire (green, green/yelow, or bare copper) to ground wire, neutral wire (white) to neutral wire, and ot wire (black) to hot wire. Wrap the connection with electrical tape.
    Step 2: Spread apart the wires so that the hot wires are on one side of the outlet box and the neutral wires are on the other side.
    Note:
    1. This fan only needs one set of input wires (black, white, and ground wire). Both of the fan and lights will be controlled by the remote controller.
    2.This fan can only be connected to an on/off switch if you have one, not a dimmer switch.

  4. Attach the Canopy
    Take away the “S” hook (GG). Align the “L” slots from the canopy to the canopy screws (HH) on the mounting bracket (AA), rotate the canopy to lock it onto the mounting bracket (AA). Lighten the canopy screws (HH)CROSSIO CFL 20 Inch
Crystal Ceiling Fan with Lights - Parts 7

  5. Attach the Crystal
    Slide the silicone elastic ring (1) and fastener (1)) onto a position slightly above the middle of the long crystal (KK). Insert the long crystals (KK) and short crystals (LL) alternately onto the fan assembly (A).

REMOTE CONTROL INSTRUCTIONS

CROSSIO CFL 20 Inch Crystal Ceiling Fan with Lights - Parts
13

  1. Insert 2 batteries before using: AAA 1.5V battery x 2pcs (not included)
  2. Mark and drill screw holes in the wall, then insert the remote holder anchors (NN),
  3. Use short wood screws (MM) to fix the remote holder (QQ) onto the wall.

REMOTE CONTROL INSTRUCTIONS

  1. Turn on/off the light.
  2. Quick switch of the light color: Yellow Light >White Light >Natural Light
  3. (12)Adjust the light color temperature.
  4. SETUP: remote signal pairing.If the remote control loses signal of the fan, press and hold this button at the very beginning after it’s powered on from wall switch, After the fan flashes or beeps, it’s paired successfully,
  5. (11)Adjust the brightness of the light.
  6. Fan moves forwards or reversely.
  7. (8)(16)Fan speed.
  8. Turn off fan and light.
  9. Night mode, lights will be dimmed when press this button.
  10. Timing for 2 hours for the fan,
  11. Natural wind of the fan, fan speed will change automatically when use this function.
  12. Turn off the fan,

NOTE:
Please insert 2 batteries before using. AAA 1.5V battery x 2pcs (not included).

APP CONTROL INSTRUCTIONS

NOTE: Scan the QR code and install the APP in your phone, or search and install “FanLamp Pro” from Google Play, Apple App and other APP stores. Make sure your phone is connected to the internet and bluetooth enabled.

CROSSIO CFL 20 Inch Crystal Ceiling Fan with Lights - QR
Codehttp://www.jasonghost.com/fanlamppro/

| Pairing: Click the pair button within 5 seconds after turning on the fan from the wall switch. Once the fan flashes or beeps, it has been successfully paired with your phone and can now be contralled through the app.
---|---
| Slide the slider to change the fan speed.
| Slide the slider to change the brightness of the light.
| Quick switch for “White” light color.
| Quick switch for “Yellow” light color.
| Quick switch for “Natural” light color.
| Night mode: Dim the lights.
| Fan moves forward.
| Fan moves reversely.
| Change the direction of the wind. (Not supported)
| Timing the fan.
| Natural wind: The fan speed will change automatically when you use this function.
| Sleeping wind, (Not supported)
| Turn on/off the light.
| Turn on/off the fan.
| Unpairing: Click the unpair button within 5 seconds after turning on the fan. Once the fan flashes or beeps, it has been successfully unpaired from your phone.
|
---|---
https://www.youtube.com/watch?v=vXB7NVM0JYM| http://www.jasonghost.com/fanlamppro/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CROSSIO User Manuals

Related Manuals