SCANGRIP 10K LED Work Light User Guide
- June 1, 2024
- SCANGRIP
Table of Contents
SCANGRIP 10K LED Work Light
Settings
Settings
Enable or disable notification of low battery or adjust the time in which the
app scans for new lamps.
Consent
Review and change your consent to gathering of analytical and crash data.
Web Site
Press to access our Web site.
Privacy policy
Press to read the privacy policy.
Help
Press to access the Scangrip App Quick
Guide.
Scanning and Connecting
Lamp status
Is shown when an active connection is made. Displays power status and if the
lamp has PIN lock enabled.
Select up to 4 lamps
Select a lamp by pressing their name or the yellow selection dot.
Control > Lamp
Press “Control” and select a lamp to control one of the connected lights.
Refresh/Scan
Press the update icon or swipe down to update the list of lamps.
Groups
Press “Groups” to access Groups screen. Can also be accessed by swiping to the
left.
NOTE:
If the lamp or no lamps can be found on Android, check that location data
(GPS) is enabled and the app has permission to access location.
Group Function
Units Screen
Select up to 4 lamps
Select a lamp by pressing name or the yellow selection dot.
NOVA 10K, NOVA SPS and NOVA CAS lamps can be grouped. So can AREA 10 SPS and
AREA 10 CAS. Other models can only be grouped with lamps from the same series.
Control - > Create group
Press “Control” and select “Create group” to create a group with the connected
lights.
Groups
Press “Groups” to access Groups screen. Can also be accessed by swiping to the
left.
Groups screen
Control
Press to control or delete the selected group.
Group selection
Select a group by pressing name or the yellow selection dot.
Units screen
Press to access Units screen.
Group control screen
Work lights
On/Off synchronization
The first press of the button turns on the lamps and synchronizes the group to
the chosen setting.
Light icon
Will be off until first press on On/Off, no matter if a lamp in the group is
on.
Sliders
Values will not be sent to lamps until the group is turned on.
Rename
Press to change the group name in the app.
Groups
Press to access Groups screen.
Group control screen
UV lamps
On/Off synchronization
Pressing turns off all lamps if any is on.
Otherwise, pressing will enter the warning screen for the user to confirm
before turning on all connected lamps with the set curing time.
Light icon
Will be on whenever a lamp in the group is on.
Remaining curing time
Display set curing time when off and counts down during curing.
Curing time slider
Adjust slider or press value to the right to change the curing time for all
lamps in the group.
Slider moves down with remaining time. Changing while curing restarts the
countdown from that value.
Rename
Press to change the group name in the app.
Groups
Press to access Groups screen.
NOVA 10K
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
Rename
Press to change the name of the lamp in the app.
Units
Press ‘Units’ button to return to the Units screen.
Power status
Shows operation time left and battery level as well as when in back-up mode
and connected to mains power. Time left is updated every time a command is
sent.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press ‘Units’ button to return to the Units screen.
MULTIMATCH Series
Power status
Shows operation time left and battery level depending on whether it is
connected to power supply or is in back-up mode. Time left is updated every
time a command is sent.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Current CCT
Changes to display the current color temperature (CCT) as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
CCT slider
Adjust slider or press value to the right to change the color temperature.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press ‘Units’ button to return to the Units screen.
AREA 10 SPS
Power status
Shows operation time left and battery level as well as when in back-up mode
and connected to mains power. Time left is updated every time a command is
sent.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
180°/360° buttons
Press to change between complete and directional lighting.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press ‘Units’ button to return to the Units screen.
NOVA CAS / CONNECT series
Power status
Shows remaining battery in % and battery level depending on whether it is
connected to power supply or is in back-up mode. Battery level is updated
every time a command is sent.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press ‘Units’ button to return to the Units screen.
AREA 10 CAS / CONNECT
Power status
Shows remaining battery in % and battery level depending on whether it is
connected to power supply or is in back-up mode. Battery level is updated
every time a command is sent.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
180°/360° buttons
Press to change between complete and directional lighting.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press ‘Units’ button to return to the Units screen.
MULTIMATCH CONNECT
Power status
Shows remaining battery in % and battery level depending on whether it is
connected to power supply or is in back-up mode. Battery level is updated
every time a command is sent.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Current CCT
Changes to display the current color temperature (CCT) as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
CCT slider
Adjust slider or press value to the right to change the color temperature.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press ‘Units’ button to return to the Units screen.
SITE LIGHT Series
Power status
Only mains powered. A loading spinner appear until the command has been
received.
Light icon
Shows if the lamp is on and changes with the brightness.
Current brightness
Changes to display the current brightness as shown on the slider.
Brightness slider
Adjust slider or press value to the right to change the brightness.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press “Units” button to return to the Units screen.
UV-EXTREME Series
Power status
Only mains powered. A loading spinner appear until the command has been
received.
Light icon
Shows if the lamp is on.
Remaining curing time
Display set curing time when off and counts down during curing.
Curing time slider
Adjust slider or press value to the right to change the curing time.
Slider moves down with remaining time. Changing while curing restarts the
countdown from that value.
Rename
Press to change the name of the lamp in the app.
PIN lock
Shows PIN status. Press to lock or clear PIN code on lamp.
Units
Press “Units” button to return to the Units screen.
Safety Screen
Remaining curing time
Display set curing time when off and counts down during curing.
Safety slider
Drag slider all the way to the right to turn on the lamp. If released the
slider will return to the left starting point.
Cancel
Press to return to the Control screen.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>