SCANGRIP SUNMATCH 4 Rechargeable LED Work Light Instruction Manual
- June 1, 2024
- SCANGRIP
Table of Contents
SCANGRIP SUNMATCH 4 Rechargeable LED Work Light
Product Specifications
- Model: SUNMATCH 4
- Part Number: 03.5657
- CCT SCAN Function: Stepless sweep from 2500K to 6500K
- Lumen Output: 500lm reduced to 250lm after 3 minutes
- Dimmer: Stepless dimmer 10-100%
- LED Type: Ultra high CRI+ COB LED
- Spot Light: High power LED, 50-500lm (200lm at Spot)
- Lux Output: 700-1400 lux@0.5m (Spot: 5000 lux@0.5m)
- Colour Temperature Range: 2500K-6500K (Spot: 4000K)
- CRI: 96+ (Spot: 95 CRI)
- Battery: 3.7V / 2600mAh Li-ion, 2-10h runtime (Spot: 3h)
- Dimensions: 188x58x26mm, Weight: 267g
- Impact Protection: IK07, IP Rating: IP65
- Charging Input: 5V DC 1A, Charging Cable Included
Key Features
Product Usage Instructions
- Turning On/Off and Adjusting Brightness
- Press the on/off button to cycle through the Main, Spot, and Off modes.
- To adjust brightness, press and hold the on/off button while in Main mode.
- Release, press, and hold again to increase brightness.
- The light will flash at the lowest and highest levels until the button is released.
- Color Temperature Adjustment
- Press the CCT SCAN button to manually change color temperature when the light is on.
- Hold the CCT SCAN button for 2 seconds to activate CCT SCAN mode.
- In CCT SCAN mode, press the button to pause or hold for 2 seconds to deactivate.
- CCT indicator corresponds to specific color temperature ranges.
- Battery Management
- The lamp switches to low mode (250lm) after 3 minutes of high mode (500lm) use.
- Use a 5V, 1A USB charger for recharging. Battery level indicated by LED bars.
- Avoid over-discharging the battery and always replace it with the same type.
- Safety Precautions
- Avoid looking directly into the beam of light to prevent dazzling.
- Keep a minimum distance of 0.1m from lighted objects to reduce fire risk.
- Follow electrical equipment regulations and do not use near naked flames.
WARNING
- Always respect applicable legislation for working with electrical equipment to reduce the risk of accidents.
- Avoid looking directly into the beam of light, as this will result in dazzling.
- Do not use the lamp near a naked flame.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
USE
Activate the CCT SCAN function to sweep stepless in the interval from 2500K to 6500K. At any point, the CCT SCAN function can be locked.
- Press the on/off button to turn the lamp on in the sequence: Main > Spot > Off.
- Press and hold the on/off button while the main light is on to start dimming. Release, press, and hold again to increase.
- At the lowest and highest levels, the light will flash until the button is released.
- When the lamp is turned off the lamp will remember the setting of the main light.
- When the light is on, press the CCT SCAN button to change the color temperature manually.
- When the light is on, press and hold the CCT SCAN button for 2 seconds to activate the CCT SCAN mode.
- When in CCT SCAN mode, press the CCT SCAN button to pause the CCT SCAN mode.
- When in CCT SCAN mode, press and hold the CCT SCAN button for 2 seconds to deactivate CCT SCAN mode. When in CCT Scan mode, the CCT indicator corresponds to the following color temperature ranges: 25: 2500-3300K, 35: 3301-4100K, 45: 4101-4900K, 55: 4901-5700K, 65: 5701-6500K.
- To save battery and avoid the risk of overheating an intelligent built-in system turn the lamp to low mode (250 lumen) after 3 minutes of use at high mode (500 lumen).
CHARGING / BATTERY
- During charging, the 4 led bars will indicate the level of charge in red color. When fully charged, all 4 led bars will light up with green color.
- Battery capacity indicator: when the lamp is OFF, press and hold on/off button for 2 sec. (Capacity indicator function is disabled when the lamp is on).
- Use 5V, 1A USB charger.
- Always replace the battery with a new one of the same type and grade.
- Don’t leave battery discharged. Otherwise, it could be over-discharged and may NOT be able to be recharged.
DISPOSAL
Discarded electrical products must not be disposed of together with household waste. Please use recycling facilities. Ask your local authority or retailer for advice on recycling.
- The battery must be removed from the device before it is broken up.
- The device must be disconnected from the mains when the battery is removed.
- Please dispose of the battery safely.
Frequently Asked Questions (FAQ)
Q: How do I know when the product is fully charged?
A: During charging, all 4 LED bars will light up in red colour. When fully charged, they will turn green.
Q: Can I replace the light source in this luminaire?
A: The light source is not replaceable. When it reaches its end of life, the entire luminaire should be replaced.
Q: What should I do if the battery is over-discharged?
A: Avoid leaving the battery discharged for too long as it may not be able to recharge. Always replace it with a new one of the same type and grade.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>