CARBON XT 24510-1 Automatic Phone Holder User Manual

: June 1, 2024
: CARBON XT

Table of Contents

Product Features
Package Contents
Specifications
Warnings
Installation And Use
Troubleshooting
FCC WARNING
Customer Service
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CARBON XT 24510-1 Automatic Phone Holder

CARBON XT 24510-1 Automatic Phone Holder

Product Features

Package Contents

(1) Automatic Phone Holder & 10W Wireless Charger Head
(1) Suction Cup Base with Telescopic Arm
(1) I Vent Clip Base
(1) I 1 Type-C Cable
(1) 12V Power Plug
(1) User Manual

Specifications

Car Charger Input: 12V-24V DC 2A
Car Charger Output: DC 5V/3A, 9V/2A, 12V/1.5A
Car Charger Fuse Protection: Integral Protection Against Overloads
Wireless Phone Charger Input: DC 9V/1.67A
Wireless Phone Charger Output: Max 10W, 7.5W, 5W
Wireless Phone Charger Aux. USB Charge Port : 5V 1A
Wireless Charging Distance : 8mm or Less
Conversion Efficiency : Greater Than or Equal to 75%
Working Frequency : 110-205 KHz

Warnings

INDOOR USE ONLY.
Do not block the wireless charging area with metal or magnetic items. Remove all metal or magnetic devices on the back of your phone and/or case before use.
Product to be used with Qi certified mobile phones.
Check manufacturer’s specifications of your device prior to use. Custom Accessories, Inc. limits its liability only to the replacement of product.
Do not install any accessory near or on air bags. Never obstruct driver’s view.
To prevent damage to the suction cup base, make sure the temperature of the phone holder is above freezing during installation and removal.
People who use a pacemaker should consult their doctor before using this product.
Normal operating temperature is -10° C to 60° C (14° F to 140° F).
Do not disassemble charge[
Keep out of reach of children.

Installation And Use

Decide how you would like to mount your phone holder/ charger to your vehicle.
Suction Cup Mount
- Remove the protective film from the suction cup base.
- Make sure the locking base tab is flipped up, in the released position.
- Make sure the intended mounting area is free of dust, dirt and oily protective coatings. Use rusting alcohol to clean the mounting area if needed.
- Place the suction cup on the dash or window surface of your choosing and push down while flipping the locking base lever down.
- The suction cupolas should now be locked in the place of your choosing.
  Air Vent Mount
- Squeeze the push button to spread the two arms of the air vent mount.
- Slide the air vent mount over one of the slats in your air vent assembly.
- When the air vent mount is Inserto fully into the air vent slat, release the push button.
- The air vent mount should now be firmly attached to your air vent.
Attach the head of the unit to the base.
- Unscrew the ball joint locking ring and place over the ball joint on the base.
- Pop the ball on the base into the circular receiver on the head o1 the unit.
- Orient the head of the unit in the desired position.
- Screw the ball joint locking ring tightly to secure the head on the base.
Insert the Qualcomm car charger (includes) into the vehicle’s 12-24V port.
Install the JSB Type-A to The)e-C cable.
- The USB Type-A side of the cable should be plugged into the included car charge[
- The USB Type-C side of the cable should be plugged into the bottom of the phone holder head.
Power should now flow to the phone holder / charge[ The LED coloured base will turn blue and the automatic arms of the phone holder should open.
Place your wireless-charging capable mobile phone in between the automatic arms of the phone holder. The arms of your phone holder will automatically close and the charging process will legion.
When charging properly, the LED colored base will tam from blue to red.
To remove your phone, simply place your finger on the arm release button and the automatic arms will open. The phone holder features a large capacitor which allows the unit to have enough power for 2{l open/close iterations even when power is removed. This allows you to remove your phone after vehicle shut down.
There is an optional 5V 1A charging TJSB port on the right side o1 the unit. This port can be used to charge a second phone.

Troubleshooting

Phone Holder / Charger will not illuminate.

Is your system 12V – 24V? This is required.
Check all connections.
Is the car charger inserted completely?
The lace of the charger should light up blue.
Are the USB Type-A to Type-C cable ends inserted completely?

Phone Holder / Charger will not charge my phone (LED indicator does not turn red).

Check your phone’s specifications. Make sure your phone is capable of a wireless charge.
For the Phone Holder/ Charger to work properly, the coilin side your phone must align with the coil inside of the Phone Holder/ Charger. The clear phone holder legs are adjust tile (up and down). Try different settings to align the coils.
Remove all metal or magnetic devices an the back of your phone and/or case. Any metal or magnetic plates on the back of your case or phone will interfere with the wireless charge.
Remove all finger rings, pop-devices, and similar devices from the back of your phone and/or case. These devices will cause your phone to be too far from the charging coil inside the phone holder/ charge[
Is your phone case too thick? Try using the charger without your case to test. You may need a thinner case.

FCC WARNING

Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference t hat may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protect ion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of t he following measures

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect t he equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.

WARNING: This product is suitable for mount in car window, dash or vent. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Fcc Warning