young BIKE RACK Hitch Single 1 Bike Rack with Ramp Instruction Manual

June 1, 2024
YOUNG

young BIKE RACK Hitch Single 1 Bike Rack with Ramp

Specifications

  • Bike Rack Parts:
    • Beam Assembly
    • Front Wheel Holder
    • Bottom Fixing Bracket
    • Support Rod
    • Connecting Block
    • Lock Beam Diameter: Less than 7mm
  • Ramp Parts:
    • Ramp
    • Quick-release pin

Assembly Steps for Bike Rack

  1. STEP 1: Align and install Front Wheel Holder with Beam Assembly.
  2. STEP 2: Place assembled components into Bottom Fixing Bracket and secure with bolts.
  3. STEP 3: Insert Support Rod into Bottom Fixing Bracket and tighten.
  4. STEP 4: Insert Connecting Block into Support Rod and secure with knob.
  5. STEP 5: Secure components with pin and ensure proper fit.

Parts for bike rack

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(2\)

Parts for ramp young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(1\)

Parts List for bike rack

Part# Description Qty
1 Beam Assembly 1
2 M10*25 Outer Hexagon Bolt Kit 4
3 Front Wheel Holder 1
4 M10 Long Outer Hexagon Bolt 2
5 M10 Lock Nut 3
6 Bottom Fixing Bracket 1
7 Support Rod 1
8 M10 Low Square Neck Bolt 1
9 Connecting Block 1
10 M16 Shockproof Bolt 1
11 φ16 Spring Washer 1
12 φ16 Flat Washer 1
13 φ3.8 Pin 1
14 Velcro 4

Parts List for ramp

Part# Description Qty
1 Ramp 1
2 Quick-release pin 1

Required Tools(Not included

Name Imperial Metric
Monkey Wrench 12’’ 300mm
Open Wrench 7/16’’ 11mm
Open Wrench 11/16’’ 17mm
  1. STEP1
    Put the holes of the Front Wheel Holder (3) and the Beam Assembly (1) aligned, install 4pcs M10*25 Outer Hexagon Bolt Kit (2) and tighten them.
    young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(4\)

  2. STEP2
    Place the components assembled in steps 1 above into the Bottom Fixing Bracket (6), align the holes, install 2pcs M10 Long Outer Hexagon Bolt (4) and 2pcs M10 Lock Nut (5), and tighten the bolts.
    young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(4\)

  3. STEP3
    Insert the Support Rod (7) into the Bottom Fixing Bracket (6), align the holes, install the M10 Low Square Neck Bolt (8) and the M10 Lock Nut (5), and tighten them until the support rod does not move.

  4. STEP4
    Insert the adjustable Connecting Block (9) into the Support Rod (7), and properly tighten the knob so that it does not slide down.

  5. STEP5
    Align the holes of the folding tube with the holes on the vehicle’s 2″ hitch receiver, then connect the two parts as shown below. Place an M16 shockproof bolt (10), through the φ16 Spring Washer (11), φ16 Flat Washer (12) and the aligned holes. Screw the bolt in place by Monkey Wrench (Not included) and secure it with the φ3.8 pin (13), making sure to place the pin through the holes on the bolt.

Bike Installation Instructions

Before placing the bicycle, stand up the support rod in the middle, snap the front tire of the ebike into the front wheel holder, place the rear tire in the beam, and then use the ratchet wheel straps to fix the front wheel, rear wheel, and seat tube of the bicycle as shown in the figure below.
It’s generally recommended that using the ratchet wheel strap to fix the crossbar (if applicable) or the middle tube (or seat post). Considering that some electric bikes have thicker downtubes, please do not strap the downtube.

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(6\)

  • Note: Use the ratchet wheel strap to fix and tighten the seat tube, middle tube, or the position of the crossbar near the seat tube/middle tube of the bicycle.
  • Note: Use the ratchet wheel strap to fix and tighten the front wheel of the bicycle.
  • Note: The rear tire fixing seat needs to be placed in front of the rear wheel.

Bike Installation Instructions(tire width<2.5”)

If your tire width is less than 2.5”, please use velcros to fasten the front and rear tires.
Only 2pcs of Velcro(14) are required to fix the tires, the rest are for spare.

  • young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp- \(7\)Note: The velcro fixes the front tire as illustrated
  • Note: The velcro fixes the rear tire as illustrated

How to Adjust the Wheel Cradle

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(8\)

How to Use the Ramp

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(1\)

YOU ARE ALMOST THERE!

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(6\)

Dimension

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(9\)

Technical Specifications

  • Maximum Load: Bicycle under 100LBS
  • Maximum bicycle wheelbase 50”
  • Applicable Types of Hitched Bike: Electric Bike/Regular Bike
  • Not intended for use with mopeds, motorcycles or 3 wheels bikes
  • Applicable for tires width within 5”, extra velcros (included) need to be applied for tires within 2.5
Model Name YOUNG ELECTRIC Sole R
Description 2” Hitch 1-Bike Rack with Ramp
Material Aluminum & Steel
Maximum Weight Capacity 100lbs
Applicable Vehicles Vehicles with 2” receiver
Package Size 55.9×13.9×8.3in
Package Weight 44.1lbs

WARNINGS

  • Do not overload beyond the bike rack’s weight capacity of 100lbs.
  • Do not carry more than 1 bike on the carrier.
  • The bike rack is not intended for transporting humans or animals.
  • If you are planning to load only one bike, it is recommended to place it in the position closest to the vehicle.
  • All bikes must be secured properly before operating the vehicle.
  • Make sure the front of the bike(s), when mounted, is at or above the bottom of the bumper to avoid damage to the bike(s).
  • Do not carry flammable items on the bike rack.
  • If using the bike rack to transport electric bicycles, please remove the batteries from the bicycles prior to transporting them. This will help reduce the weight supported by the carrier.
  • During long trips, frequently check the straps and bike position, especially if traveling on rough terrain.
  • Please do not make alterations to the product, as it can pose potential hazards to your safety.
  • Failure to heed these warnings may result in personal injury and/or property damage.
  • To prevent serious injury or death, inspect the bike rack for any signs of wear, corrosion and fatigue before each use. Do not use the bicycle rack if parts are bent, broken, deformed or missing. If parts are bent, broken, damaged or missing, remove the rack from your vehicle before operating the vehicle.

Young Electric Warranty Policy
Young Electric is committed to providing our customers with a quality shopping experience, for the products we sell, we provide a 2-year warranty from the date of purchase, which includes non-artificial product defects. This warranty does not cover issues caused by normal wear and tear including (but not limited to) weather, scratches, dents, rust, accidents, unlawful vehicle operation, misuse, abuse, neglect, theft, unauthorized modifications, or unauthorized repair.

Please strictly follow the instructions on how to use it, no warranty and responsibility are provided for defects caused by improper fit, improper vehicle installation, installation on an “unsuitable” vehicle, incorrect installation of the bike on the rack, or overloading of the weight limit of the rack. This warranty terminates if the purchaser transfers the product to any other person.
If a product is believed to be defective, the purchaser should directly contact Young Electric Team at 888-933-8899 or through support@youngelectricbikes.com

Disclaimer of Liability: Repair or replacement of a defective product or the issuance of a refund or credit (as determined by Young Electric) is a purchaser’s exclusive remedy under this warranty.
Young Electric shall not be liable for any direct, indirect, consequential, incidental, special, punitive or any other damages in connection with the purchase, use or handling of this product.
Some states do not allow the exclusion or limitation of consequential or incidental damages, and the above limitation may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from state to state.

THANK YOU FOR CHOOSING A
YOUNG ELECTRIC HITCH BIKE RACK!

YOUNG ELECTRIC Bike racks are designed to make your bicycles well hitched with stability & safety. Carefully read this Owner’s Manual before assembly, it will give you all the information necessary for assembly and adjusting.
YOUNG ELECTRIC works hard to guarantee you a bike rack that is properly assembled and correctly adjusted when it leaves our factory. Please contact our Help Center if you still have any questions after reading this manual. Our customer service staff are ready to answer questions regarding assembly, performance, operation, service parts or other general services.
Email: support@youngelectricbikes.com

Keep this Owner’s Manual in a safe place for future reference. All content in this manual is subject to change as we continually work to refine our products.
This manual contains warnings, cautions, and notes, therefore please carefully read all of this information for your safety.Give special attention to any information that has a warning or caution symbol before or next to it. Also, pay attention to any information preceded by NOTICE as this will be important information that may be related to safety.
Always properly maintain and care for your bike rack so original quality and safety are retained.

Get Support

young-BIKE-RACK-Hitch-Single-1-Bike-Rack-with-Ramp-
\(1\)

https://youngelectricbikes.com support@youngelectricbikes.com Toll Free Number: 888-933-8899

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

YOUNG User Manuals

Related Manuals