Empava 36RH09 30 in. 400 CFM Ducted Kitchen Glass Island Range Hood User Manual
- June 6, 2024
- Empava
Table of Contents
RANGE HOOD
Installation and Operation
Manual
READ AND SAVE THESE INSTRUCTIONS MANUAL
Please note that this product is marked with this symbol:
According to the Waste of Electrical and Electronic Equipment (WEEE)
directive, WEEE should be separately collected and treated. If at any time in
the future you need to dispose of this product, Please do NOT dispose of this
product with household waste. Please send this product to WEEE collecting
points where available
Dear consumer,
Thanks for your purchase of our range hood and we hope we can fully satisfy
all of your needs. Please read the entire instructions carefully before
proceeding to obtain the best
results of operation the range hood.
TECHNICAL CHARACTERISTICS
Model number: EMPV-36RH09 EMPV-36RH10
Total power: 208W
Motor power: 200W
LED Lights: 4x2W
Voltage: 120V
Frequency: 60Hz
Filter: Baffle filter
Control: Touch Control
MAIN PARTS NAME
Dimensions
IMPORTANT SAFETY INSTRUCTIONS:
INSTALLATION:
USE ONLY WITH RANGE HOOD CORD CONNECTION KITS THAT HAVE BEEN INVESTIGATED AND
FOUND ACCEPTABLE FOR USE WITH THIS
MODEL RANGE HOOD. A UTILISER SEULEMENT AVEC UNE TROUSSE DE RACCORDEMENT DE
CORDON DE HOTTE VERIFIEE ET APPROUVEE
POUR EMPLOI AVEC CE MODELE DE HOTTE. INSTALLATION REQUIREMENT
- Do not install the range hood where there are many doors ro windows in order to avoid effecting the exhaust efficiency of the hood that is caused by air convection. (fig.1)
- Install the range hood right above the cooking surface. The recommended distance between the cooking surface and the lower edge of the range hood is a minimum of 27.56″ to a maximum of 31.5″. (Fig.2)
- In order to get the best performance, do not extend the vent pipe too long, and try to make the bend of the vent pipeless and straight, make sure the vent pipe connection is firm and airproof. (Fig.3)
- After hanging the range hood on the wall, make sure the hood is level and vertical. (Fig.4)
- The air Outlet is not allowed to connect to chimney flues or combustion gas ducts. The air outlet should under no circumstances be connected to ventilation ducts for a room in which fuel-burning appliances are installed.
INSTALLATION PROCEDURES
SAFETY WARNING
THE HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS
NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.
Step 1:
Fix the position of the range hood in accordance with the recommended height
between 27.56″-31.5″ from the cooking surface and the lower edge of the
hood.
Step 2:
Put vent pipe (set the vent pipe into the outlet of the blower box, screw up
2pcs M4 screws to fix).
Step 3
Match the 8pcs expansion hanger with the hoods assembly.
Step 4:
Use 16pcs M4 screws to fix the hangers.
Step 5:
Put the inner duct cover and outer duct cover on the blower box. The pull out
the exhaust pipe to the level of the inner duct cover. 
Step 6:
As per the screw positions on the upper support frame, drill 4 holes (about
Φ0.31″), then fill the expanding rubber into the holes. Aiming the holes on the
ceiling, fix the ceiling cover with the expanding screws tightly and make sure
it is firm.
Step 7:
Install expansion strip with the ceiling cover (Upper one).
Step 8:
Pull the inner cover to the ceiling, aiming the upper support frame, fix it
with M4*12 screws provided.
Step 9:
Install grease filter. Match the fix pin to the fix hole and button the filter
gently as the direction of arrow A.
OPERATING INSTRUCTION
- Electronic Switch
1.How to use the Touch Control
| Press to turn
on /off the light.
---|---
Press to select the high speed.
Press to select the medium speed.
Press to select the low speed.
Press to select on/off.
2). Touch Control
| Turn on and
turn off the light
---|---
Set time
Speed down, from speed 3 to speed 1
Speed up, from speed 1 to speed 3
To start max speed
To turn on and turn off the power
Time setting: Press for approximately 3 seconds.
Touch **+**(Speed up) to set hour.
Touch **-**(Speed down) to set the minute.
MAINTENANCE
CAUTION : NEVER PUT YOUR HAND INTO THE AREA HOUSING WHILE THE FAN IS
OPERATING.
FOR THE OPTIMAL LEVEL FO OPERATION, CLEAN THE RANGE HOOD SURFACE, AN AND
ALUMINUM FILTER REGULARLY.
-
Use only mild soap or detergent solutions to clean the range hood surface. Dry surfaces using soft cloth.
-
Using a stainless steel cleaner to bring the glow back into a stainless finish.
-
Clean the filter once a week or according to use status. Press the buckle of the filter slightly, take off the filter and put it into warm soapy water using mild detergent, wipe the filter with soft brush. Replace the filter after it’s dry.
-
Clean the motor fan and other inside parts once a half-year or according to use status by QUALIFIED PERSON.
-
DO NOT clean the motor with water or other liquid.
TO REPLACE LIGHT
To replace Led light (Pic.1)
Сaution: LED light can not replace a new bulb, just replace a new LED light
assembly.
Make sure all the control switches are off, and the range hood is unplugged!
Please follow below instructions:
- Take out the filters, and cut off the wire connection of the light.
- Press the spring according to the arrow direction, then you can take off the LED light.
- You can replace a new LED assembly no more than rating.
- Then put the light assembly to the hood in reverse direction. Connect the wire of the lamp.
- Fit on the filters.
WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low or
medium settings.
b) Always turn hood ON when cooking at high heat or when flambeing food
(i.e.Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).
c) Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate for the size of the
surface element.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWING : SMOTHER FLAMES with a close-
fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL
TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN – You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels – a violent steam
explosion will result.
d) Use an extinguisher ONLY if:
- You know you have a Class ABC extinguisher, and you already know how to operate it.
- The fire is small and contained in the area where it started.
- The fire department is being called.
- You can fight the fire with your back to an exit.
WARNING : TO PROVIDE PROTECTION AGAINST ELECTRIC SHOCK, CONNECT TO PROPERLY GROUNDED OUTLETS ONLY.
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This
appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING – Improper grounding can result in a risk of electric shock.
Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance
WARNING – TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
TROUBLESHOOTING
CAUTION : Disconnect the power supply before servicing.
| Status | Cause and Method of Repairing | Tools required |
|---|---|---|
| No power | Check circuit breakers | |
| If the power supply is damaged, please call for a qualified person | Philips |
Screwdriver
The motor does not run| a). The motor is broken, replace the motor.
b). The switch control is broken, replace the switch.
c). The capacitor is broken, replace the capacitor.| Philips Screwdriver
Body vibration| a). The installation is not correct, check it and make sure
the hood is level.
b). The fan is broken, replace motor assembly.
c). The fan motor was not properly installed, check and make sure it is firmly
installed.| Philips Screwdriver
Noise vibration| Something dropped into the blower, check and clean blower.|
Philips Screwdriver
Weak suction| a). The distance from the range hood to the cooking surface is
too far, make sure the distance between the bottom of the hood to the cooking
surface is minimum 24″ to maximum 27″.
b). Windows, doors, and drafts can affect the performance of the range hood.
c). There are other air conditions affecting the vent pipe, make sure the
lower vent pipe’s exit is in a downward direction.
d). The running rate of the motor slows down, replace the motor or capacitor.
If the range hood is near the window,
the best solution is to protect the back of the range hood from the draft
caused by a window or door.| Philips Screwdriver
Light does not work| Replace LED lamp.| Philips Screwdriver
EMPAVA APPLIANCE INC.
Add: 15253 Don Julian Rd, City of Industry, CA 91745
Tel:888-682-8882
www.empava.com