Pulsar SG64WP-BT Port PoE Switch Installation Guide

: June 1, 2024
: Pulsar

Table of Contents

Pulsar SG64WP-BT Port PoE Switch
Features
Technical Description
Installation
Operation indication
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Pulsar SG64WP-BT Port PoE Switch

Pulsar-SG64WP-BT-Port-PoE-Switch-PRODUCT

Features

Switch 6 ports 4 ports PoE 10/100/1000 Mb/s (data transfer and power supply)
2 ports 10/100/1000 Mb/s (UP LINK)
60 W for each PoE port, supports devices complaint with the IEEE802.3af/at/bt standard
Supports auto-learning and auto-aging of MAC addresses (8K size)
LED indication
Additional assembly elements
Warranty – 2 years

Example of use.

$Pulsar-SG64WP-BT-Port-PoE-Switch-FIG-1 $1$$

Technical Description

General description.

SG64WP-BT is a 6-ports PoE switch designed to supply IP devices operating in IEEE 802.3af/at/bt standard, e.g. cameras IP, video intercoms, Access control etc.
Automatic detection of any devices powered in the PoE standard is enabled at the 1 – 4 ports of the switch. The UP LINK ports are used for connection of another network device via RJ45 connector. The LEDs at the front panel indicate the operation status (description in the table below).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a separate power cable for each device. This method allows supplying other network devices, such as IP phones, wireless access points or routers.

Block diagram.

$Pulsar-SG64WP-BT-Port-PoE-Switch-FIG-1 $2$$

Description of components and connectors.

Table 1. (see Fig.2)

Element no. (Fig. 2)	Description
[1]	2 x UP LINK port
[2]	4 x PoE port (1÷4)
[3]	Power Socket of the DC
[4]	Additional mounting elements

$Pulsar-SG64WP-BT-Port-PoE-Switch-FIG-1 $3$$

Technical parameters.

Table 2.

Ports| 6 10/100/1000 Mb/s ports (4 x PoE + 2 x UP LINK) with connection speed auto-negotiation and MDI/MDIX auto-cross
---|---
PoE power supply| IEEE 802.3af/at/bt (1÷4 ports), 52 V DC / 60 W at each port *
Protocols, Standards| IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth| 16,6 Gb/s
Transmission method| Store-and-Forward

Optical indication of operation

| Switch power supply; Link/Act;

PoE Status

Installation

Requirements

Unit should be mounted in confined spaces, in accordance, with normal relative humidity (RH=90% maximum, without condensing) and temperature from -10°C to +40°C. Ensure the free flow of air around the unit.
The device shall work in a vertical position that guarantees sufficient convectional air flow through ventilating holes of the enclosure.
The load balance should be done before the installation of Switcha. The given value of 60 W per port is the maximum value referring to a single output. The total power consumption should not exceed 120 W and depends on the current efficiency of the PSU, taking account of the power intake for the own needs of the device.
The increased demand for power is particularly evident in the case of cameras with heaters or infrared illuminators – when launching these features, the power consumption increases rapidly, which may adversely affect the operation of the switch.
The device is designed for continuous operation and is not equipped with a power switch.
Therefore, appropriate overload protection in the power supply circuit should be provided. The electrical system shall be made by applicable standards and regulations.

Installation procedure

Connect switch to the power supply unit.
Connect the power supply to the 230 V socket.
Connect the camera wires to the RJ45 connectors (PoE connectors).
Check the optical indication of switch operation (see Table 3).

Connection schemes:

$Pulsar-SG64WP-BT-Port-PoE-Switch-FIG-1 $5$$ $Pulsar-SG64WP-BT-Port-PoE-Switch-FIG-1 $6$$

Operation indication

Table 3. Operation indication

$Pulsar-SG64WP-BT-Port-PoE-Switch-FIG-1 $7$$

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment should be disposed of separately from normal household waste.