SEALEY HT105LED.V3 Rechargeable Head Torch Instruction Manual
- June 1, 2024
- SEALEY
Table of Contents
3W SMD LED RECHARGEABLE HEAD TORCH
MODEL NO: HT105LED.V3
HT105LED.V3 Rechargeable Head Torch
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR
THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
SAFETY
Inspect the cable and connector
for wear and damage to ensure items are safe before connecting to the power
supply. If worn or damaged DO NOT use.
Ensure the torch is fully
charged before initial use.
DO NOT charge in damp conditions.
DO NOT turn the torch on when it is being charged.
DO NOT shine directly into your, another person’s or an animal’s eyes.
DO NOT allow children to use the torch.
DO NOT handle or move the torch whilst it is being charged.
DO NOT use the torch if you suspect that the battery or the torch casing is
damaged.
DO NOT leave battery in a discharged state, recharge battery immediately.
Before storage, fully recharge the battery, subsequently recharge the battery
at least once every six months of non-use.
DO NOT attempt to open, disassemble, modify or service the battery pack.
DO NOT crush, puncture, short external contacts or dispose of in fire or
water.
Replace only with the battery
pack designated for this product.
Recycle or dispose of used
battery as stipulated by local regulation.
If the electrolyte in the cells
gets on your skin, thoroughly rinse with water. If it gets in your eyes, rinse
thoroughly with cool water and seek immediate medical attention.
INTRODUCTION
Hands-free SMD LED spotlight with adjustable inclination to direct light as
required. Features three settings – full light, low light or flashing.
Adjustable headband and foam brow for added comfort. Supplied with micro USB
charging lead.
SPECIFICATION
Model No ………………………………………………… HT105LED.V3
Battery: ………………………………………. 3.7V 1.5Ah Lithium-ion
Charging Time: …………………………………………………………4hr
LED Type: ……………………………………………………….3W SMD
Lumen Output: ……………………………………………………. 220lm
Operating Time: ……………………….2.5hr @100%, 8hr @ 30%
OPERATION
4.1. CHARGING (fig.2)
4.1.1. Remove USB socket cover on battery pack.
4.1.2. Connect the USB lead to the port on the rear of the battery pack and a
USB power socket. Turn on the power supply.
4.1.3. The charging LED on the lamp will light RED to show that charging has
commenced.
4.1.4. When the battery has fully charged the LED will turn GREEN.
4.1.5. Switch off power supply, remove charging lead and replace socket cover
on battery pack.
4.2. OPERATION
4.2.1. Adjust the three straps to fit your head size.
4.2.2. To turn on press the red button on the back of the torch unit, once for
100%, twice 30% three times flashing and once more to turn off.
4.2.3. To switch on rear red light, with front light on hold down red button
for 2 seconds, the rear red light will light up. To switch off, switch off
front light, rear light will default to off.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products containing batteries
(as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd’s Batteries Producer
Registration Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
HT105LED.V3 Issue 3 (H,3) 12/05/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>