xiaomi 103748 Motion-Activated Night Light User Manual

xiaomi 103748 Motion-Activated Night Light User Manual

Product Overview

Read this manual carefully before use and retain it for future reference.

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

Installation

Installing the batteries
Turn the front cover counter-clockwise to unscrew it from its hemispherical housing. Open the battery cover and install three AA batteries in the battery compartment.

Connecting with Mi Home / Xiaomi Home App

This product works with the Mi Home/Xiaomi Home app*. Use the Mi Home/Xiaomi

Home app to control your device, and to interact with other smart home devices. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already. Or search “Mi Home/Xiaomi Home” in the app store to download and install it.

Open Mi Home/Xiaomi Home app, tap “+” on the upper right, and then follow prompts to add your device.

Notes:

• Please connect with the app before installing the night light.
• Make sure the Bluetooth is enabled on your phone when connecting with the app.
• If the night light needs to be reconnected with the app, please delete this device from the app and restore its factory settings first, then reconnect it.
• The version of the app might have been updated, please follow the instructions based on the current app version.
• The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on your device should be taken as the default.

Mounting the light

Choose a flat and dry place to install the night light.

Wipe the desired surface clean, then peel off the protective film from the adhesive sticker of the base. Position the base on the surface and press it down firmly to make sure it is properly secured. Then, install the night light onto the magnetic base and adjust the angle as preferred.

Note: For accurate detection, it is recommended to face the light downwards when the base has been mounted over 1.9 m above the floor.

Mounting point is over 1,9 m above the floor  **Facing downwards

**

Mounting point is between 0.5-1.5 m above the floor  **Facing straight forward

**

Mounting point is below 0.5 m above the floor  **Facing upwards

**

Note: For different mounting heights, the angle needs to be adjusted based on the user’s height and the desired usage scenario to achieve the optimal result.

How to use

Night Light Function

The night light will turn on automatically when it detects human body motion in the dark environment and will turn off automatically after a while if no human body motion is around.

The night light function is enabled by default with its lighting up for 15 seconds in 2.5 lumens.

You can enable or disable the night light function on the page of Mi Motion- Activated Night Light 2 (Bluetooth) in the app. The brightness can be adjusted between 2.5 to 25 lumens and the lighting up time between 15 to 60 seconds.

Note: To do the settings or update the firmware in the app, enable the Bluetooth function on your phone first, then move your body around within the induction range of the night light or push the Bluetooth switch to either side.

Sensor Function

The night light has the sensor functions to not only detect the human body motion, but also the ambient light status of bright or dark.

You can access the night light to the devices that support Bluetooth gateway function, such as the Mi Bedside Lamp and the Mi Smart LED Ceiling Light. Tap Bluetooth gateway in the settings of the night light page in the app.

After the night light is successfully accessed, then you can check the logs of the human body motion and the ambient light status. You can also configure to interact this night light with other devices in smart scenes.

Note: You can view the logs only when the night light is accessed to the devices that support the Bluetooth gateway function.

Detection Area

Note: The detection area is a 120″ area directly at the centre in front of the night light. The detection area covers 0-6 min front of the light, and 0-2.5 m to the sides. The detection effect depends on the angle of the light, ambient temperature, body size, and moving speed. The illustrated detection area is based on the direction the logo is facing.

Restoring Factory Settings

Within two seconds, quickly press the Bluetooth switch to either direction three times. Once the night light turns on and then turns off, the factory settings have been restored successfully.

Specifications

• Model: MJYD02YL-A
• Operating Temperature: -10°C to 40°C
• Compatible with: Android 4.4 & iOS 9.0 or above
• Wireless Connectivity: Bluetooth 4.2 BLE
• Rated Voltage: 4.5 V
• Rated Power: 0.35 W
• Item Dimensions: ø 80 × 62 mm
• Net Weight: Approx. 121 g
• Luminous Flux: 2.5–25 lm
• Operating Frequency: 2402–2480 MHz
• Maximum Output Power: ≤8 dBm

Precautions

Do not cover the detection area of the light.

When cleaning the surface of the light, wipe it clean with a soft cotton cloth and do not use any corrosive solvents.

Do not install the light near heat sources such as AC or heating vents, or in direct sunlight. Nor install the light near sources of humidity such as humidifiers or water heaters.

Make sure it is firmly installed with the magnet, so as to avoid the risk of accidental dropping.

Make sure the Mi logo is always upright when installing and using the night light.

When the brightness of the night light is reduced after a period of normal use, the battery level may be insufficient. Please replace the batteries with new ones and dispose of the used batteries in accordance with local rules and regulations, so as to avoid environmental pollution.

The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.

For indoor use only.

Please pay attention to the positive (+) and negative (-) poles when installing the batteries.

After non-rechargeable batteries are depleted, they cannot be charged. Different types of batteries, and old and new batteries should not be mixed.

Remove leaking batteries from the night light and dispose of them in accordance with local rules and regulations, so as to avoid environmental pollution.

The batteries must be removed from the night light when it is not used for a long time, or when the night light is being disposed of.

Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.

The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

• Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
• Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
• Natural wear and aging of consumables or components during use (such as batteries, etc.).
• Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
• If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

EU Declaration of Conformity

This product complies with the legal requirements of the following European Union directives: Directive No. 2014/53/EU

WEE

This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before
first use and keep this user manual for future reference. Pay particular attention to the safety
instructions. If you have any questions or comments about the device, please contact the
customer line.
✉ www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
• Alza | Alza.co.uk
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.cz
• alza.de
• alza.hu
• alza.sk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>