The Pond Guy LEDPro Series High Output Lights Instruction Manual

May 21, 2024
the Pond guy

LEDPro™ Series High Output Lights
Product Manual

For Models:

  • LEDPro™ Mini 1-Watt Light Kit, 3 Pack (Item #120813)
  • LEDPro™ 3-Watt Light Kit, 3 Pack (Item #120810)
  • LEDPro ™ 6-Watt Light Kit, 3 Pack (Item #120817)
  • LEDPro™ 12-Watt Single Light (Item #120828)

IMPORTANT INFORMATION

Please read these instructions thoroughly before use. Failure to follow instructions may result in equipment damage or failure, losses, injury or death.
DANGER:
To avoid possible electric shock:

  • If the power cord, lens, or other components have been damaged, DO NOT operate, LEDPro™ Lights should be replaced.
  • Close supervision is necessary when the unit is used by or near children.

WARNING:
To reduce the risk of electric shock:

  • Connect only to a properly grounded receptacle, which is serviced by a Ground Fault Circuit Interrupter and never remove the ground pin from the plug.
  • Provide a “drip loop” for the power cord. This is a loop in the cord below the level of the receptacle or plug that prevents water from traveling along the cord in the direction of the receptacle.
  • ALWAYS unplug the LEDPro™ Lights from power source when not in use, and before installing, removing or servicing the LEDPro™ Light’s components.
  • If an extension cord is necessary, a cord with a proper rating should be used. A cord may overheat if the cord is rated for less amperes or watts than the unit rating.
  • DO NOT immerse the LEDPro™ Light’s plug, Transformer (A) or Splitter (B) in water. If any components get wet, do not attempt to use.
  • The LEDPro™ Lights are NOT suitable for use in swimming pools, swimming ponds, or other situations where bodily contact is made with the water.

Important – LEDPro™ Lights may be used in or out of water. When used in open air application, unplug the lights and allow to cool before servicing.
**CAUTION:**
To reduce the risk of equipment damage or failure:

  • DO NOT place LEDPro™ Lights near flammable or other dangerous materials or objects.
  • DO NOT use the LEDPro™ Lights in fluids other than water.
  • DO NOT exceed the voltage and wattage indicated on the transformer.
  • DO NOT operate during freezing conditions. Remove LEDPro™ Lights and store in a protected location.

IMPORTANT:
The Pond Guy® is not responsible for equipment damage or failure, losses, injury or death resulting from failure to follow safety precautions, misuse or abuse of equipment.

TECHNICAL SPECS

MODEL # OF LIGHTS WATTAGE ITEM  NUMBER
LEDPro™ Mini 1-Watt 3 3×1 Watts 120813
LEDPro ™ 3-Watt 3 3×3 Watts 120810
LEDPro ™ 6-Watt 3 3×6 Watts 120817
LEDPro ™ 12-Watt 1 1×12 Watts 120828

INSTALLING YOUR LEDPRO™ LIGHTS:

DO NOT TAMPER WITH POWER CORD. Lights may be placed in or out of water.
Step 1
Plug the two-pin connector on the end of each Light(C) cord into the Splitter(B) and tighten plastic retaining nut.
Step 2
Plug the two-pin connector on the end of the Splitter(B) cord into the Transformer(A) and tighten plastic retaining nut. PLEASE NOTE: Splitter (B) cannot be fully submerged. Please ensure the placement is located out of the water.
Step 3
Place Lights(C) in desired locations.
Step 4
Make sure Photocell (E) is located out of the water, in an area exposed to natural light.
Step 5
Plug the Transformer(A) into a standard 110 volt outlet with GFCI.

The Pond Guy LEDPro Series High Output Lights - LIGHTS

MAINTAINING YOUR LEDPRO™ LIGHTS

MAINTENANCE:
WARNING:
Before performing any maintenance, always unplug the LEDPro™ Lights from the power source.
CLEAN lenses regularly to remove algae/debris buildup that will reduce light intensity.
CLEAN with a soft cloth or brush with water, or a descaler if needed. When using a descaler be sure to rinse components well before reinstalling.
TROUBLESHOOTING:
One or more lights fail to illuminate:

  • Check connection from Light(C) to Splitter(B)
  • Inspect Lens(D) for algae/debris accumulation
  • Ensure bulb is properly seated in housing
  • Replace bulb (3-Watt light set only)

All lights fail to illuminate:

  • Make sure Transformer(A) is properly seated in electrical outlet
  • Make sure electrical outlet provides power
  • Check Splitter(B) to Transformer(A) connection
  • Check connections from Lights(C) to Splitter(B)
  • Ensure bulbs are properly seated in housing and check photocell

Lights stay on during the day:

  • Make sure photocell is upright, unobstructed & exposed to sunlight

REPLACEMENT PARTS / ACCESSORIES

DESCRIPTION ITEM NUMBER

LEDPro ™ 3-Watt Replacement Bulbs (Choose from red, blue, yellow, warm white, cool white. Warm white comes standard)| 120812
ThePondGuy® Colored Lens Set for LEDPro™ Mini 1-Watt (Comes with red, blue, yellow & green lenses )| 190135
20’ Extension Cord (Maximum of 1 extension should be added per light)| 110525

PRODUCT WARRANTY

LEDPro™ Series High Output Lights carry a 3-year warranty. The Pond Guy® will repair or replace any units found to be defective. This limited warranty is extended exclusively to the original purchaser and begins from the date of original purchase receipt. Abuse or misuse of this product or power cord alterations void all warranty. Please call for a Return Authorization Number prior to returning product by calling our Customer Care Department at 866-766-3435. Failure to request an RMA number may result in delay or dismissal of your warranty claim.

THANK YOU FOR CHOOSING:
The Pond Guy® Inc.
We Know Ponds™ 15425 Chets Way
Armada, MI 48005
866-POND-HELP (766-3435)
thepondguy.com
View other great products on-line at
www.thepondguy.com
thepondguy.com
866-POND-HELP (766-3435)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals