ELECTRALITE ELA-41712 Bodhi LED Cct Link Light Instruction Manual

ELECTRALITE ELA-41712 Bodhi LED Cct Link Light

Specifications

• Product Name: BODHI LED CCT LINKLIGHTS
• CCT Switch: WW-NW-CW
• Power Switch: ON/OFF
• Connection Options : Direct V2, Cable (2000 mm)
• Available Sizes:
  • ELA 41712
  • ELA 41713
  • ELA 41714
  • ELA 41715
  • ELA 21665 – 8 Type
  • ELA 21666 – 8 Type

Product Usage Instructions

Installation

We strongly recommend that the ceiling lights be installed by a qualified electrician. If you choose to install the lights yourself, please carefully read through the instructions provided and keep them for future reference.

Changes to Building Regulations
Ensure that any electrical work complies with the relevant Building Regulations. For significant electrical work, consider notifying your Local Authority Building Control Department for inspection and testing.

Important Safety Information
Before installation or servicing, always disconnect the electrical supply at the mains. Adhere to all instructions and warnings provided with the product. If unsure, consult a qualified electrician.

General Information
Avoid mounting the light fitting on damp surfaces to prevent discoloration. The fitting is double-insulated and should not be earthed. Ensure a solid mounting point to support the weight of the fitting.

Fixing Instructions
To prevent damage to concealed wiring, confirm the direction of the supply cable before drilling and fixing holes. Do not connect any part of the fitting to an Earth wire or terminal.

Connection options

Available sizes

• Thank you for selecting this product. It has been thoughtfully designed and carefully manufactured to ensure a high level of reliability and performance.
• We strongly recommend that ceilings be installed by a qualified electrician. If, however, you decide to carry out your installation, please read through these instructions carefully before commencing work, and retain them for future reference.

Please note, that the important safeguards and instructions appearing in this letter are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care are factors that cannot be built into any product and must be supplied by the person installing and caring for the thing.

Changes to Building Regulations

As of 1 January 2005, changes to the Building Regulations affect domestic electrical installations in England and Wales. You don’t need to be a qualified electrician to make changes to your home’s electrical system, but the work must be done in accordance with the standards in the Regulations.

You do not need to notify your Local Authority if you do minor electrical work such as:-

• replacing or repairing a socket, light or cable in any room
• adding extra spurs, sockets or lights to an existing circuit (except in a kitchen, bathroom, or outdoors)

However, the work must be done to the standards in the Wiring Regulations and you should consider having the work checked by a competent electrician to make sure it is safe.

Before you start other electrical work such as:-

• adding new circuits to your existing installation
• any work (other than repairs / replacements) in a room where there is water (eg. kitchen, bathroom, etc.)
• any work (other than repairs / replacements) outdoors (eg. installing garden lighting or sockets, etc.)

You must notify your Local Authority Building Control Department, which has responsibility for ensuring the work is inspected and tested.

Where you have any work done by an electrician who is a member of a competent person self-certification scheme, the electrician will be able to certify the work complies with the Regulations and you do not need to notify your Local Authority.
We recommend that you make yourself aware of the Regulations before you undertake any work and if you require any clarification you should contact your Local Authority Building Control Department.

Important Safety Information

• Install under current applicable building and electrical installation regulations.
• Before installation and servicing, disconnect the electrical supply at the mains.
• Carefully observe all instructions or warnings that are labeled on, or supplied with, your product.
• If in any doubt, consult a qualified electrician.

General Information

Do not mount this fitting onto damp surfaces such as newly painted or plastered areas as this may cause discoloration of the finish.

Fixing instructions

This light fitting is double-insulated and must not be earthed. Do not attach any part of it to an Earth wire or terminal. Make sure that there is a joist or other solid mounting at the point of fixing. This is necessary to take the weight of the fitting. To avoid damage to concealed wiring during installation, establish the direction of the supply cable before drilling holes.

Wiring ceiling fittings

For Double Insulated items (Class 2): These are marked with the symbol

Check that…..

• You have correctly identified the house wires.
• The connections are tight.
• No loose strands have been left out of the connection block.

Switch on!
You may now switch the electricity back on at the mains.

Cleaning care
The fitting should be cleaned with a soft, dry cloth only. Do not use polishes or abrasive cloths.

Safety information

For your safety, please remember the following:
Always switch off the supply before removing shades/covers, changing lightbulbs, or cleaning.

This product should be disposed of responsibly at the end of its life. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice (Waste Electrical and Electronic Equipment Directive)

HELPLINE
If you receive this item with parts broken or missing, please telephone: 0333 0050077
Please have ready your name, address, tel. no., product reference, where purchased, and parts required. An answering service is in operation outside office hours and during busy periods. We regret that we are unable to advise on internal house wiring.
Cascade Holdings Ltd, Gorse Mill, Gorse Street, Oldham, OL9 9RJ

EU Authorised Representative: Authorised Rep Compliance
Ground Floor, 71 Lower Baggot Street, Dublin, Ireland, D02 P593

FAQ

• Q: Do I need to be a qualified electrician to make changes to my home’s electrical system?
  • A: While it’s not necessary to be a qualified electrician for minor work like replacing sockets or lights, major installations require compliance with regulations and may need an inspection by a competent electrician.
• Q: Can I mount the light onto newly painted surfaces?
  • A: It is recommended not to mount the fitting onto damp surfaces like newly painted or plastered areas to avoid potential discoloration of the finish.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>