DOMUS CHAM-BT-RF-5C Bluetooth RF 5-1 Universal Controller Instruction Manual
- June 13, 2024
- DOMUS
Table of Contents
CHAM-BT-RF-5C Bluetooth
RF 5-1 Universal Controller
Instruction Manual
CHAM-BT-RF-5C
Variant| Item No.|
---|---|---
20141| CHAM-BT-RF-5C| Thank you for purchasing your new CHAM-BT-RF-5C
Controller, Please take the time to read and understand the instruction sheet
below. Failure to do so may void warranty.
Specifications
Type of controller:| 5ch 4 in 1 universal RF+ Bluetooth controller| Input
voltage (VDC):| 12-24V DC
---|---|---|---
Method of control:| PWM| Output voltage (VDC):| 12-24V DC
Method of dimming:| PWM (Pulse Width Modulation)| Output current (A):| 5x4A
Housing colour:| (L) 145mm x (W) 46.5mm x (H) 16mm| Output wattage (W):| 12V
DC – 48W per channel (x5).
24V DC – 96W per channel (x5).
Housing size (mm):| Black plastic colour housing| Expandable signal:| Ye s *
Requires:| Constant Voltage 12-24V DC LED driver**| |
* Multiple 5CH data repeaters can be used in a single circuit.
** Constant Voltage LED driver required (not included) depending on
requirements of light source (12V or 24V DC).
- 4 in 1 universal RF+Bluetooth LED controller, radio frequency: 2.4GHz
- 4 different device modes DIM, CCT, RGBW and RGB+CCT in 1 controller, and selectable by dial switch
- Enables to control ON/OFF, light intensity, colour temperature, RGB colour of connected LED lights
- Ultra powerful to control Single Colour, CCT, RGBW, RGB+CCT LED strips
- Controlled through both smart App and remote controls, no gateway required for local control
- The controller can be configured as six different light types: RGB+CCT, RGBW, RGB, CCT, DIM, ON/OFF using the smart APP
- Easy & quick pairing to the smart App by simply pushing the Prog. button
- Mesh network, much longer control distance, transmits received signal to neighbor devices
- Up to 30m transmission distance between every two neighbor devices
- Encrypted two-way communication, quick status feedback, safe & reliable data transmission
- Compatible with universal RF+Bluetooth remotes, each LED controller can pair to max. 8 remotes
- Cloud control is available for remote access, works with Amazon Alexa and Google Home
- Waterproof grade: IP20
Safety & Warning
- DO NOT Install with power applied to device.
- DO NOT operate the dial switches for device mode selection with power applied to device.
- DO NOT expose the device to moisture.
Operation Pair/delete the pairing with RF+Bluetooth remote
- Do wiring according to connection diagram.
- Pair LED controller with RF+Bluetooth remote: please refer to the instruction of the remote that you would like to pair with.
- Delete the pairing:
(a). Wire up the LED controller correctly, power on.
(b). Press and hold down the “Prog.” button on the controller for over 3 seconds (or reset power of the device 8 times continuously if the button is not accessible to factory reset the device) until the connected light flashes, which means well deleted.
Note: Note: factory resetting will restore all configured parameters of the device on the APP to factory default setting.
Pair with smart APP
- Do wiring according to connection diagram.
- Download EasyThings APP from IOS APP Store or Android Google Play to your smart phone or tablet by searching “EasyThings”. (As shown in Figure 1)
- Enable Bluetooth on your smart phone or tablet. (As shown in Figure 2).
- Run Easythings APP, tap add button “+ ” on the APP to add device, then choose “Discover devices” to discover device, then short press the “Prog.” button on the LED controller twice (or reset power of the controller twice continuously) to set the device into pairing to APP mode. (As shown in Figure 3 & Figure 4 & Figure 5). Note: multiple LED controllers can be discovered by the APP at the same time.
- Once the device/devices are discovered, tick the device/devices and tap “Save” button, the will be added successfully. (as shown in Figure 6)
Configure Light Type Using smart APP
- Press and hold the device icon to enter into control interface, then tap button “ ” at upper right corner to enter into edit page of this device (As shown in Figure 7 & Figure 8).
- Then tap “Light Type” to enter light type configuration page, for this driver, it can be configured as 6 light types: RGBCCT, RGBW, RGB, CCT, DIM, ON/OFF. Once select a Light Type, tap “ ” at upper right corner to confirm, the connected light will flash to indicate successful configuration. (As shown in Figure 8).
Wiring Diagrams
RGB+CCT Mode Note: please make sure the dial switches are at position for
RGB+CCT mode as shown in above diagram.
RGB Mode Note: please make sure the dial switches are at position for
RGBW mode as shown in above diagram.
CCT Mode Note: please make sure the dial switches are at position for DIM
mode as shown in above diagram.
DIM Mode Note: please make sure the dial switches are at position for DIM
mode as shown in above diagram.
Note:
- The lamp must be installed by professional electrician
- Ensure the power supply is switched off before fitting this product
- Do not touch the lamp when in use
- Keep away from hot steam and corrosive gas
29-31 Richland St. Kingsgrove. Sydney NSW 2208 Australia
Phone: 02 9554 9600
Fax: 02 9554 9433
enquiries@domuslighting.com.au
www.domuslighting.com.au
Date: February 1, 2023 2:16 PM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>